• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.319.1-319.1
• /
• 2016

Recently, the Al-doped ZnO (ZnO:Al) films are intensively used in thin film a-Si solar cell applications due to their high transmittance and good conductivity. The textured ZnO:Al films are used to enhance the light trapping in thin film solar cells. The wet etch process is used to texture ZnO:Al films by dipping in diluted acidic solutions like HCl or HF. During that process the glass substrate could be damaged by the acidic solution and it may be difficult to apply it for the inline mass production process since it has to be done outside the chamber. In this paper we report a new technique to control the surface morphology of RF-sputtered ZnO:Al films. The ZnO:Al films are textured with vaporized HF formed by the mixture of HF and H2SiO3 solution. Even though the surface of textured ZnO:Al films by vapor etching process showed smaller and sharper surface structures compared to that of the films textured by wet etching, the haze value was dramatically improved. We achieved the high haze value of 78% at the wavelength of 540 nm by increasing etching time and HF concentration. The haze value of about 58% was achieved at the wavelength of 800 nm when vapor texturing was used. The ZnO:Al film texture by HCl had haze ratio of about 9.5 % at 800 nm and less than 40 % at 540 nm. In addition to low haze ratio, the texturing by HCl was very difficult to control etching and to keep reproducibility due to its very fast etching speed.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2003년도 학술대회 논문집
• /
• pp.68-71
• /
• 2003

We fabricated Ni-substrate for YBCO coated conductors and evaluated the effects of pressing and annealing time on texture. Ni substrate was fabricated by powder metallurgy technique and compacts were prepared by applying uniaxial or isostatic pressure. The texture of substrate made by applying cold isostatic pressure (CIP) was stronger than that by uniaxial pressure. The texture of substrate made by CIP had a strong 4-fold symmetry and [111] ∥ ND texture after annealing temperature of 100$0^{\circ}C$. It is to be noted that the degree of texture was almost independent of annealing time and the full-width at half-maximum (FWHM) of in-plane and out-of-plane was measured to be in the range of 9.55$^{\circ}$-10.53$^{\circ}$ and 8.57$^{\circ}$-9.85$^{\circ}$, respectively. Development of strong cube texture of Ni-substrate made by powder metallurgy technique in our study is considered to be suitable for the application of YBCO coated conductors.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2003년도 추계학술대회 논문집
• /
• pp.55-58
• /
• 2003

We fabricated the textured Ni substrate and evaluated the effects of processing variables on microstructural evolution and texture transformation. Ni-rods as an initial specimen were prepared by two different methods, i.e., powder metallurgy(P/M) and plasma arc melting(PAM) The texture of the substrate was characterized by pole-figure and surface condition was evaluated by atomic force microscopy. It was observed that the texture of substrate made by P/M did not significantly varied with annealing temperature of 800~120$0^{\circ}C$ and the full-width at half-maximums (FWHM) of both in-plane and out-of-plane were 9$^{\circ}$~10$^{\circ}$. On the other hand, the texture of substrate made by PAM was more dependent on the annealing temperature and the FWHMs of in-plane texture was 9$^{\circ}$~13$^{\circ}$ at the temperature range. In addition, twin texture, (221)＜221＞, was formed as the temperature increased further. The grain size of substrate made by P/M was smaller than that made by PAM and this difference was correlated to the microstructure of initial specimens.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1249-1250
• /
• 2006

Cube textured Ni substrate were fabricated for YBCO coated conductors from the initial specimens prepared by powder metallurgy (P/M) and casting and the effects of annealing temperature and reduction ratio on texture formation and microstructural evolution were evaluated. The initial specimens were rolled and then annealed in the temperature at $600^{\circ}C{\sim}1200^{\circ}C$. A strong cube texture formed for P/M substrate, and the degree of texture did not significantly vary with annealing temperature of $600^{\circ}C{\sim}1100^{\circ}C$. On the other hand, the texture of casting substrate was more dependent on the annealing temperature and twin texture and several minor texture components started to form at $1000^{\circ}C$.

• 한국재료학회지
• /
• 제9권11호
• /
• pp.1049-1054
• /
• 1999

근사단결정 다이아몬드막 성장시 입자의 정렬을 개선하기 위한 집합조직성장의 2단계 성장방법을 제안하였다. 메탄조성 4%, 기판온도 $850^{\circ}C$ 조건에서 (100) Si 기판에 - 200V 바이어스를 인가하여 20분동안 전처리 하였다. 처리한 기판을 2%[CH$_4$], 기판온도 $810^{\circ}C$에서 2~35시간동안 <100> 집합조직을 지니도록 1단계로 성장시켰다. 이 시편의 성장표면을 평탄화하기 위하여 (100) 면이 성장하도록 2% [CH$_4$], 기판온도 $850^{\circ}C$ 조건에서 2단계 성장시켰다. 1단계 성장시간에 따른 다이아몬드막의 배열정도를 {111} X-ray pole figure의 반가폭 변화를 통해 관찰하였다. 1단계 성장 후 입자정렬은 막의 두께가 증가할수록 개선되었다. 그러나 <100> 집합조직의 표면조직은 피라미드 형태의 굴곡을 피할 수 없었다. 2단계 성장시 (100) 면의 성장으로 인해 막의 표면은 평탄화되었으며, 이때 입자의 정렬은 1단계 성장시간에 크게 의존하였다.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2001년도 High Temperature Superconductivity Vol.XI
• /
• pp.55-55
• /
• 2001

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2001년도 High Temperature Superconductivity Vol.XI
• /
• pp.69-69
• /
• 2001

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2005년도 High Temperature Superconductivity Vol.XV
• /
• pp.62-62
• /
• 2005

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2005년도 High Temperature Superconductivity Vol.XV
• /
• pp.68-68
• /
• 2005

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.387.2-387.2
• /
• 2016

Glass texturing is a sufficient method for changing the surface morphology to enhance the light trapping. In this study, glass texturing was applied to the perovskite solar cell for improving the current density. Glass substrates (back-side glass of FTO coated glass substrate) were textured by randomly structure assisted wet etching process using diluted HF solution at a constant concentration of etchants (HF:H2O=1:1). Then, the light trapping properties of suitable films were controlled over a wide range by varying the etching time (1, 2, 3, 4 and 5 min.). The surface texturing changed the reflected light in an angle that it can be reflected by substrate glass surface. As a result, Current density and cell efficiency were affected by light trapping layer using glass texturing method in perovskite solar cells.