• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.63.2-63.2
• /
• 2011

결정질 실리콘 웨이퍼를 이용한 고효율 태양전지를 제작하기 위해서는 반드시 고려해야 할 주요 인자들이 있다. 그 중에서도 Base resistivity, Thickness, Doping concentration, Texture size, Texture angle등의 주요 인자를 PC1D 시뮬레이션 프로그램을 이용하여 최적화 해 보았다. 그 결과, Base resistivity값은 낮을수록 좋으나 지나치게 낮을 경우 재결합으로 인해 효율이 떨어지기 때문에 Base resistivity = $1{\Omega}{\cdot}cm$에서 최대 효율을 얻을 수 있었다. 또한, Thickness는 두꺼울수록 R=${\rho}$(L/A)의 식에 의해 직렬저항이 증가하여 효율이 감소하므로 Thickness = $200{\mu}m$ 정도가 적정 값임을 확인할 수 있었다. Doping concentration의 경우 높을수록 재결합으로 인해 효율이 떨어지며 Doping concentration = $3.69{\times}10^{-20}cm^{-3}$에서 가장 좋은 효율을 보였다. Textrure size와 Textrure angle은 그 값이 클수록 빛의 흡수 정도가 증가해 효율이 증가함을 볼 수 있었고 Textrure size = $2{\sim}4{\mu}m$, Texture angle = $79^{\circ}$에서 높은 효율을 보여주었다. 이와 같은 조건에서 고효율 태양전지를 제작을 위한 시뮬레이션을 한 결과, 16.23%의 변환효율을 얻을 수 있었다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.10
• /
• pp.938-945
• /
• 2003

We fabricated Ni-substrate for YBCO coated conductors and evaluated the effects of pressing and annealing temperature and time on texture. Ni substrate was fabricated by powder metallurgy technique and compacts were prepared by applying uniaxial or isostatic pressure. The texture of substrate made by applying cold isostatic pressure (CIP) was stronger than that by uniaxial pressure which we attribute to the fact that the CIP method provided higher density and more uniform density distribution. It was observed that the substrate annealed at 400 C showed both retained texture and recrystallized texture. On the other hand, the texture of substrate significantly improved at annealing temperature above 500 C, forming strong 4-fold symmetry, [111] II ND texture, and FWHM of 9∼10 . It is to be noted that the degree of texture was almost independent of annealing temperature (500∼1000 C) and annealing time(1∼54 min, at 1000 C). EBSD and AFM analysis indicated that 99% of grain boundaries was low angle grain boundary and RMS was approximately 3 nm, respectively. Development of strong cube texture and high fraction of low angle grain boundary of Ni-substrate made by powder metallurgy technique in our study is considered to be suitable for the application of YBCO coated conductors.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.608-610
• /
• 2003

In the paper, we have investigated the reflective cholesteric display based on the polymer stabilization. The bistability in the polymer stabilized cholesteric texture(PSCT) films was observed and wider viewing angle was achieved due to imperfect planar texture.

• Journal of Information Display
• /
• v.4 no.3
• /
• pp.26-28
• /
• 2003

In the paper, we investigated the Bragg reflective cholesteric display based on polymer stabilization. We studied the bistability in the polymer stabilized cholesteric texture (PSCT) films and baused on which we achieved wider viewing angle though imperfect planar texture.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.17 no.3
• /
• pp.288-296
• /
• 1992

This paper describes an improved 2D QPS(quadrature polar separable) filter design and its applications to texture processing. The filter kernel pair consists of the product of a radial weighting function based on the finite PSS (prolate spheroidal sequences) and an exponential at tenuation function for the orientational angle. It is quadrature and polar separable in the frequency domain. It is near optimal in the energy loss because we let the orientational angle function approximate the radial weighting function. The filter frequency characteristics is easy to control as it depends only upon the design specifications such as the bandwidth, the directional angle, the attenuation constant, and the shift constant of the central frequency. Some applications of the filter in texture processing, such as the generation of the texture image, the estimation of orientation angles, and the segmentations for the synthetic texture image, are considered. The result shows that the filter with the wide bandwidth can be used for the generation of discrimination of the strong orientational textures and the segmentation results are good.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.10a
• /
• pp.194-197
• /
• 1997

The texture of a 0.25mm dia high-carbon(0.73%) steel wire made by drawing the patented and brass coated 1.4mm wire through 22 dies with a die-angle of 12$^{\circ}$has been measured. The ideal fiber texture was obtained in the center layer, while the circular texture and the near fiber texture having {111}<110> and weak {112}<110> components were obtained in the intermediate and surface layers, respectively. The circular texture was approximated by {110}<110> plus {110}<114>. The texture could be predicted by the Taylor-Bishop-Hill theory coupled with FEM for deformation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.136-137
• /
• 2008

Solar cell's efficiency depends on silicon's characteristic itself, or additional process such as texturing, coating, etc. Using PC1D, by adjusting Texturing, Base Resistivity, Emitter Doping, simulate many situation and observe the result. When texture Angle=$80^{\circ}$, Texture Depth=2um, Base Resistivity = 0.2, Emitter Doping = 8*Exp(19) are set, the solar cell's efficiency si 19.89%, and optimized.

• Transactions of Materials Processing
• /
• v.29 no.3
• /
• pp.127-134
• /
• 2020

It is known that the difference of texture of the polycrystalline Al sheet is not a critical parameter for the formation of aligned nanopore arrays in anodic aluminum oxide (AAO). This will be related to the polycrystalline grain in the Al sheet. The texture of each grain in the polycrystalline Al sheet is different. The mixed textures of grains have the mixing effects on the nanopore structure of the AAO. Thus, the effect of Al texture on the nanopore structure of the AAO was investigated using three types of Al single crystals with (111), (200) and (220) textures in this paper. These three types of AAO layers were fabricated by the two-step anodizing method at 40 V and temperature of 0-5℃ in oxalic acid solution. In the nanopores formed on the AAO, the average area of one nanopore and the average roundness of one nanopore were measured were measured based on the SEM images. In the hexagon obtained by connecting nanopores on the AAO, the average standard deviation of one angle deviated from 120° was measured. In the AAO nanopores with texture of (111), (200) and (220) single crystal samples, the average area of one nanopore of (200) single crystal sample was the widest, followed by (111), (220) single crystals. The average circularity of one nanopore of (200) single crystal sample was the best, followed by (111), (220) single crystals. The average standard deviation of an angle from 120° of (220) single crystal sample was the largest, followed by (111) and (200) single crystals.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.75-76
• /
• 2008

In this study, texture development and bending characteristics of strong {0002} textured were observed. AZ31 Mg alloy sheets were prepared along the angle of 0 and 12.5 degrees to the lolling direction or {0002} texture. Prepared samples with different angles to the rolling direction were rolled at room temperature condition and after subsequent heat treatment to investigate texture with x-ray diffractometer, respectively The specimen having along the angles of 0 degree to rolling direction shows the highest load and 12.5 degrees specimen shows the highest displacement among any other specimens in bending test.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.6
• /
• pp.49-56
• /
• 1998

Super precision working technique and machine tool have been continually developed thanks to advanced electronic field. To obtain good result. it is necessary to investigate surface in grinding with $mu extrm{m}$ level. There were quite many researches to satisfy these demands by using non-contact methods through the computer vision. In this study, the texture of working surface was analyzed. co-occurrence matrices was obtained from the surface roughness. Texture parameter was obtained using position operator composed of $ heta$, d according to variation of angle direction and distance. As a result, it was found that surface texture was more affected by direction($\theta$) than distance(d).