• Korean Journal of Materials Research
• /
• v.2 no.5
• /
• pp.366-374
• /
• 1992

Mechanical and impact properties of stitched S2 glass fiber reinforced polyester woven laminates composites have been studied. Laminates were stitched using Kevlar 49 thread with 1/2, 1, and 2 inch stitch spacing. Tensile and 3-point bending tests haute been performed to evaluate the mechanical properties of stitched and unstitched laminates. Impact tests at applied energy of 234.7J were performed to examine the impact behavior and toughness changes of the specimen. The same specimens were also tested repeatedly at low impact energy level of 110.2J for 3 times to evaluate damage tolerance properties. The tensile and 3-point bending test results showed that one inch spacing specimen had the highest tensile and flexural strength. It also showed the highest energy absorption capability and the best damage tolerance property at the repeated impact test. The half inch spacing specimen showed the lowest tensile strength and energy absorption property at the impact energy level of 234.7J, even though it had the highest frequency of stitching thread.

• Polymer(Korea)
• /
• v.36 no.2
• /
• pp.229-234
• /
• 2012

This paper studied the effects of the content and the orientation of the disk shape fillers on the modulus of PP composites. The experimental results were compared with the theoretical calculations which included the three dimensional ellipsoids and analyzed by two aspect ratios, ${\rho}_{\alpha}=a_1/a_3$and ${\rho}_{\beta}=a_1/a_2$proposed by Lee and his researchers. Mica and talc were used as disk shape fillers in the composites. The shapes of mica and talc were observed by SEM and aspect ratios were statistically calculated. For the case of mica, the average aspect ratios were ${\rho}_{\alpha}=13.5$ and ${\rho}_{\beta}=1.8$, and for the case of talc, they were ${\rho}_{\alpha}=3.8$ and ${\rho}_{\beta}=1.4$. Also, the effects of two aspect ratios and the content of filler on the mechanical properties were studied: For 30 wt% of mica, $E_{11}$ increased up to about 2.7 times, and for the other case of talc, $E_{11}$ increased up to about 2.3 times, respectively.

• Textile Coloration and Finishing
• /
• v.28 no.2
• /
• pp.101-108
• /
• 2016

Polypropylene(PP)/multiwalled carbon nanotubes(MWCNT) nanocomposites films and PP/poly(vinyl alcohol)/CNT nanocomposites films were prepared through melt mixing method by the extruder. The PP/CNT nanocomposites films, which contain CNT of a variable content, were prepared for the first time and research on a appropriate content of the CNT on the PP/CNT nanocomposites films was conducted. The effects of take-up speed of the extruder on the mechanical and chemical properties of the PP/CNT and PP/PVA/CNT nanocomposites film were studied. Field emission scanning electron microscope(FE-SEM) was used to examine the surface morphology and the DSC measurement and tensile test were conducted. It was found that the properties decreased when take-up speed was increased.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.1
• /
• pp.217-222
• /
• 2015

As a Creative Director one is always looking forward to formative elements of new design. The fractal image that is generated by a computer program instead of by hand suggests a geometric pattern that can grafted into a new design for each field. In this paper we look for information about the creation of a Mandelbrot fractal image that is being utilized in the design of various sectors like textile design, architectural design, exhibition design from pure painting by convergence of both technology and art composites. And it analyses about forms based on the formative principle of creation images.

• Textile Coloration and Finishing
• /
• v.21 no.4
• /
• pp.1-10
• /
• 2009

This paper surveys the physical properties of sheath/core nylon/PET high hollow composites filaments and its fabrics according to the various elution conditions such as concentration of elution, eluted time and eluted temperature. For this purpose, sheath/core nylon/PET filament was texturized and four kinds of fabric specimens were woven with different warp and weft densities. These grey fabrics were eluted with two kinds of concentrations of NaOH (30g/l, 40g/l), three kinds of eluted temperatures $50^{\circ}C,\;60^{\circ}C,\;85^{\circ}C$) and two kinds of eluted times (60min, l20min). The elution characteristics of these specimens were investigated and discussed with different elution conditions. In addition, the mechanical properties such as extensibility, bending rigidity, shear modulus and compressional work of these specimens aceording to the elution conditions were analysed and summarized with cross-sectional shapes of eluted filaments measured by SEM.

• Elastomers and Composites
• /
• v.35 no.2
• /
• pp.132-137
• /
• 2000

The cure and physical properties of EPDM foam containing ground rubber and carbon black as filler were studied. The cure time reduced with the addition of filler. This result means reducing the operation time. In case of ground rubber was used, blowing ratio, tensile strength, and elongation were decreased rapidly at above 30 phr. On the other hand, in case of carbon black, they showed similar physical properties until 70 phr was used limited to 30 phr to make a good foam, which should be due to low interfacial interaction between EPDM and ground rubber. All the EPDM foams showed excellent thermal stability.

• Fibers and Polymers
• /
• v.4 no.3
• /
• pp.135-144
• /
• 2003

Permeability of the preform is one of key factors in design of RTM (Resin Transfer Molding) mold, determination of processing conditions, and modeling of flow in the mold. According to previous studies, permeability measured in the unsaturated fiber mats are higher than that in the saturated fiber mats by about 20% because of the capillary pressure. In this study, permeabilities of several fiber preforms are measured for both saturated and unsaturated flows. A saturated experiment of radial flow has been adopted to measure the permeability of anisotropic fiber preforms with high fiber content, i.e., circular braided preforms. In this method, four pressure transducers are used to measure the pressure distribution. Permeabilities in different directions are determined and the experimental results show a good agreement with the theory. Since permeability is affected by the capillary effect, permeability should be measured in the unsaturated condition for the textile composites to be manufactured under lower pressure as in the Vacuum Assisted Resin Transfer Molding (VARTM).

• Composites Research
• /
• v.29 no.1
• /
• pp.33-39
• /
• 2016

In this study, geometric modeling and finite element analysis of 3-dimensional plain weave composite unit cell consisting of 3 interlaced fiber tows and resin pocket were performed to predict effective properties. First, tow properties were obtained from micro-mechanics finite element unit cell analysis, which were then used in the meso-mechanics analysis. The effective properties were obtained from a series of unit cell analyses simulating uniaxial tensile and shear tests. Analysis results were compared to the analysis and experimental results in the literature. Various crimp angles were considered and the effect on the effective properties was investigated. Initial failure strengths and failure sequence were also examined.

• Steel and Composite Structures
• /
• v.22 no.6
• /
• pp.1337-1358
• /
• 2016

The current study focuses on the assessment and interface response of reinforced concrete elements with composite materials (carbon fiber reinforced polymers-CFRPs, glass fiber reinforced polymers-GFRPs, textile reinforced mortars-TRM's, near surface mounted bars-NSMs). A description of the transfer mechanisms from concrete elements to the strengthening materials is conducted through analytical models based on failure modes: plate end interfacial debonding and intermediate flexural crack induced interfacial debonding. A database of 55 in total reinforced concrete columns (scale 1:1) is assembled containing elements rehabilitated with various techniques (29 wrapped with CFRP's, 5 wrapped with GFRP's, 4 containing NSM and 4 strengthened with TRM). The failure modes are discussed together with the performance level of each technique as well as the efficiency level in terms of ductility and bearing/ bending capacity. The analytical models' results are in acceptable agreement with the experimental data and can predict the failure modes. Despite the heterogeneity of the elements contained in the aforementioned database the results are of high interest and point out the need to incorporate the analytical expressions in design codes in order to predict the failure mechanisms and the limit states of bearing capacities of each technique.

• Elastomers and Composites
• /
• v.33 no.4
• /
• pp.290-296
• /
• 1998

Recycling of waste tire has been limited and very simple, few applications have been observed. This study introduces a new elastic and permeable pavement made of scrap tire. Experimental results showed that key factors affecting the compressive strength were the size of scrap tire, size of aggregate, amounts and property of binder. Also, the water permeability depended on the size of aggregate and scrap tire. The compressive strength and water permeability of the samples were 1.4 and 116 times higher than those of the conventional porous cement concrete, respectively.