• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.4
• /
• pp.257-262
• /
• 2013

The fluorine-containing waste water tends to show a higher removal efficiency through the coagulative precipitation process with calcium. However the tetrafluoroborate produced from the etching process is difficult to remaval due to it's low reactivity with calcium. The objective of this study is improving the efficiency of fluoride ion removal in tetrafluoroborate through decomposing. Research on tetrafluoroborate decomposition depending on reaction pH, temperature, and aluminum dosage were conducted, using a laboratory-scale reactor. The result shows that the reaction of tetrafluoroborate with aluminum is faster with lower pH, higher water temperature, and higher Al/T-F (Aluminum/Total Fluoride) mole ratio. It is found that there was no big change in concentration after over 120 minutes of reaction. This study is to be able to improve the efficiency of tetrafluoroborate and fluoride wastewater treatment by using aluminum.

• Journal of Electrochemical Science and Technology
• /
• v.13 no.2
• /
• pp.254-260
• /
• 2022

Trimethylammonium tetrafluoroborate (TriMA BF₄), consisting of the smallest trialkylammonium ion, was investigated for use in electrochemical double-layer capacitors. Despite the presence of a proton in TriMA⁺, cycle life tests in acetonitrile (AN) and -butyrolactone (GBL) showed a good capacity retention with a 1.8 V cut-off voltage. The rate of electrolysis of TriMA BF₄ in GBL was lower than that in AN because of the lower conductivity in GBL. As a consequence, the cells based on GBL achieved a higher capacitance and longer life than those with AN. TriMA BF₄ had a higher conductivity and lower viscosity than the quaternary salt tetraethylammonium tetrafluoroborate in GBL, as well as higher ionic mobility, these factors resulted in a higher rate capability.

• Journal of the Korean Chemical Society
• /
• v.26 no.5
• /
• pp.326-332
• /
• 1982

The structure of the complex extracted from an aqueous solution containing methylene blue and tetrafluoroborate with 1,2-dichloroethane has been investigated by comparing IR spectrum of the extract with those of pure components and appeared to be an 1 : 1 contact ion-pair between monovalent ions of opposite charge. The extraction constant obtained from the absorbance data measured at 658nm in 1,2-dichlorethane has a value of 1.1${\times}$at$10^4M{-1}$ 25$^{\circ}$C in the range from 1.43${\times}10^{-2}$ to 2.86${\times}10^{-1}$M HF. In the solvent extraction with nitrobenzene, the identical experiments show that extraction constants are increased with HF concentration possibly due to dissociation of the ion-pair in nitrobenzene.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.360-363
• /
• 2005

Biomimetic actuators composed of cellophane with an electrically conducting polyaniline(PANI) film have been fabricated and tested in air ambience conditions doped with two different counter ions such as perchlorate (${ClO_4}^-$) and tetrafluoroborate (${BF_4}^-$). Fabrication of the trilayer CP//CELLOPHANE//CP substantially enhanced the tip displacement (13.2mm) compared to the small displacement (8.3mm) of the bilaye. CP//CELLOPHANE. The ion migration among layers is the main factor behind the expansion of cellophane, while the expansion/contraction of PANI are dependent on the redox reaction of the polymer. The displacement of the composite is dominated by the humidity content. This implies that the actuation principle is possibly due to the assistance of water existing.

• Journal of the Korean Electrochemical Society
• /
• v.14 no.1
• /
• pp.9-15
• /
• 2011

The composite membranes comprising of sulfonated polymers as matrix and ionic liquids as ion-conducting medium in replacement of water are studied to investigate the effect of annealing of the sulfonated polymers. The polymeric membranes are prepared on recast Nafion containing the ionic liquid, 1-ethyl-3-methylimidazolium tetrafluoroborate ($EMIBF_4$). The composite membranes are characterized by thermogravitational analyses, ion conductivity and small-angle X-ray scattering. The composite membranes annealed at $190^{\circ}C$ for 2 h after the fixed drying step showed better ionic conductivity, but no significant increase in thermal stability. The mean Bragg distance between the ionic clusters, which is reflected in the position of the ionomer peak (small-angle scattering maximum), is larger in the annealed composite membranes containing $EMIBF_4$ than the non-annealed ones. It might have been explained to be due to the different level of ion-clustering ability of the hydrophilic parts (i.e., sulfonic acid groups) in the non- and annealed polymer matrix. In addition, the ionic conductivity of the membranes shows higher for the annealed composite membranes containing $EMIBF_4$. It can be concluded that the annealing of the composite membranes containing ionic liquids due to an increase in ion-clustering ability is able to bring about the enhancement of ionic conductivity suitable for potential use in proton exchange membrane fuel cells (PEMFCs) at medium temperatures ($150-200^{\circ}C$) in the absence of external humidification.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.6
• /
• pp.1693-1697
• /
• 2013

This study develops a novel method to remove the free cations created during the synthesis of ionic liquid. The cations are removed from the ionic liquid by size-selective adsorption onto chemically surface-modified Zeolite. The porous crystal nano-structure of Zeolite has several electron-rich Al sites to attract cations. While large cations of an ionic liquid cannot access the Zeolite nano-structure, small cations like $Na^+$ have ready access and are adsorbed. This study confirms that: $Na^+$ can be removed from ionic liquid effectively using Zeolite; and, in contrast to the conventional and extensively applied ion exchange resin method or solvent extraction methods, this can be done without changing the nature of the ionic liquid.

• Journal of the Korean Electrochemical Society
• /
• v.16 no.2
• /
• pp.91-97
• /
• 2013

Solid polymer electrolyte films are prepared by ultraviolet radiation in the mixtures of an ionic liquid salt (1-ethyl-3-methylimidazolium tetrafluoroborate, $EMIBF_4$) and solvent (acetonitrile (ACN) or propylene carbonate(PC)), and an oligomer (poly(ethylene glycol)diacrylate, PEGDA, 45-60 wt.%). Electrochemical properties of activated carbon supercapacitors adopting the solid polymer electrolyte films as a separator are also examined by cyclic voltammetry and impedance measurement techniques. As a result, the supercapacitor adopting the PEGDA as much as 45 wt.% exhibits a superior capacitance of $46Fg^{-1}$ at $20mVs^{-1}$. It seems that this is due to fast kinetics of ion conduction by sufficient film flexibility, which can be allowed by comparatively weak ultraviolet curing of small anount of the PEGDA.

• Journal of the Korean Applied Science and Technology
• /
• v.37 no.2
• /
• pp.260-267
• /
• 2020

In this study, supercapacitor based on the all solid state electrolyte with PVA(polyvinyl alcohol), ionic liquid as a BMIMBF4(1-buthyl-3-methylimidazolium tetrafluoroborate) and activated carbon/Ni-MOF composite was fabricated and characterized its electrochemical properties with function of MOF. In order to analysis and comparison that electrochemical performances [including cyclic voltammetry(CV), electrochemical impedance spectroscopy(EIS) and galvanostatic charge/discharge test] of prepared supercapacitor based on activated carbon/Ni-MOF composite and all solid state electrolyte. As a result, specific capacitance of the supercapacitor without Ni-MOF was 380 F/g which value decreased to 340 F/g after adding Ni-MOF to activated carbon as a electrode material. This result exhibited that decreased electrochemical property of the supercapacitor effected on physical hinderance in the electrode. In further, it needs to optimization of the Ni-MOF amount (wt%) in the electrode composite to maximize its electrochemical performances.

• Analytical Science and Technology
• /
• v.8 no.4
• /
• pp.675-682
• /
• 1995

Thin films of buckminsterfullerene($C_{60}$) formed by solution drop casting on Pt foil electrode surfaces were studied by cyclic voltammetry(CV) in acetonitrile(MeCN) containing quaternary ammonium or alkali-metal salts as supporting electrolyte. The electrochemical behaviors of $C_{60}$ films are found to be strongly dependent on the nature of the supporting electrolytes, especially with tetrabutyl ammonium perchlorate (TBAP, $NBu_4ClO_4$), and tetrabutyl ammonium tetrafluoroborate ($TBABF_4$, $NBu_4BF_4$). Reasonably stable films are formed into which electrons can be injected. The interaction of $C_{60}$ film with the quaternary ammonium cation may produce the fulleride salts $(TBA^+)(C{_{60}}^-)$ and $(TBA^+)_2(C{_{60}}^{2-})$. The bulk electroreduction with a controlled potential to generate the soluble $C{_{60}}^{3-}$ anions(dark red-brown color) is followed by electrooxidative deposition to produce a neutral $C_{60}$ film on the surface. The peak currents($I_{pc}$ and $I_{pa}$) of these thin film were dramatically decreased with repetitive potential scanning. These results could be explained by the adsorption-desorption phenomena and ion pairing interaction of reduced species($C{_{60}}^-$, and $C{_{60}}^{2-}$) onto the electrode surface. The peak current changes and peak potential shifts of the thin $C_{60}$ film in cyclic voltammograms formed from solution were observed by varying scan rates.

• Applied Chemistry for Engineering
• /
• v.17 no.3
• /
• pp.243-249
• /
• 2006

Porous polymer gel electrolytes (PGEs) based on poly(vinylidenefluoride-co-hexafluoropropylene) (P(VdF-co-HFP)) as a polymer matrix and polyvinylpyrolidone (PVP) as a pore-forming agent were prepared and electrochemical properties were investigated for an electric double layer capacitor (EDLC) in order to increase a permeability of an electrolyte into the PGE. Propylene carbonate (PC) and ethylene carbonate (EC) as plasticizers, and tetraethylammonium tetrafluoroborate ($TEABF_4$) as a supporting salt for the PGE were used. EDLC unit cells were assembled with the PGE and electrode comprising BP-20 and MSP-20 as activated carbon powders, Super P as a conducting agent, and P(VdF-co-HFP)/PVP as a mixed binder. Ion conductivity of PGEs increased with an increased PVP content and was the best at 7 wt% PVP, whereas electrochemical characteristics such as AC-ESR of unit cell were better in 3 wt%. And electrochemical characteristics of the unit cell with PGE were the best at a 33 : 33 weight ratio of PC to EC. Specific capacitance of a mixed plasticizer system of PE and EC was higher than that of pure PC. Ion conductivity of PGEs with a film thickness of $20{\mu}m$ was higher, but electrochemical characteristics of unit cells were higher for a $50{\mu}m$ membrane thickness. Also, the unit cell has shown the highest capacitance of 31.41 F/g and more stable electrochemical performance when PGE and electrode were hot pressed. Consequently, the optimum composition ratio of PGE for EDLCs was 23 : 66 : 11 wt% such as P(VdF-co-HFP) : PVP = 20 : 3 wt% and PC : EC = 44 : 22 wt%. In this case, $3.17{\times}10^{-3}S/cm$ of ion conductivity was achieved at the $50{\mu}m$ thickness of PGE for EDLCs. And the electrochemical characteristics of unit cells were $2.69{\Omega}$ of DC-ESR, 28 F/g of specific capacitance, and 100% of coulombic efficiency.