• Journal of the Korean Society of Industry Convergence
• /
• v.21 no.5
• /
• pp.241-246
• /
• 2018

The engine cooling system is a device that keeps the temperature of the engine room at a proper level by driving the cooling fan when the engine room temperature that occurs during driving is above a certain temperature. Recently, the vehicle cooling system has been changed to electronic system. Therefore, in this paper, we will analyze the clutch operation characteristics for designing a superior electronic fan clutch. For this purpose, an electronic fan clutch was designed and a test bed for performance evaluation was constructed and analyzed.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2009.04a
• /
• pp.688-691
• /
• 2009

항공기에는 각각의 임무에 맞게 설계된 많은 종류의 임무컴퓨터(Mission Computer)가 존재한다. 여러 센서(Sensor)에서 전송되는 신호를 처리하는 기존의 단일코어 기반 임무컴퓨터는 항공기의 성능 향상에 따른 임무 요구도의 증대와 전장 환경의 변화에 따라 기내 데이터의 양이 급격히 증가하여 정보통신의 실시간성에 한계를 보인다. 본 논문에서는 실시간 운영체제인 VxWorks를 통해서 다중채널 ARINC-429 통신모듈을 실시간으로 제어하는 멀티코어 SBC(Single Board Computer) 테스트베드(Test-Bed)를 제시한다.

• Journal of Adhesion and Interface
• /
• v.16 no.2
• /
• pp.69-75
• /
• 2015

Stone board for the rock bed was needed to reduce weight using thin thickness and reinforced materials. In this work, stone/wood board for rock bed was studied. Stone and wood were attached to reduce total weight of stone for rock bed. For reinforcing wood heat treatment method was used to change surface and mechanical properties. Mechanical strength of heat treated wood increased more than neat condition. The optimum heat treatment condition was set on $100^{\circ}C$ under tensile, flexural loads whereas surface energy was also obtained by contact angle measurement. Optimum adhesive condition was to get the maximum adhesion between stone and wood. Lap shear test was performed for stone/wood board with different adhesives such as amine type epoxy, polyurethane, chloro-rubber and vinyl chloride acetate type. Fracture surface of lap shear test was shown at wood fracture part on stone using amine type epoxy adhesive. It was found that for high adhesion between stone and wood the optimum adhesive was epoxy type for the rock bed.

• Bulletin of the Korean Space Science Society
• /
• 2002.10a
• /
• pp.77-77
• /
• 2002

• Bulletin of the Korean Space Science Society
• /
• 2003.05b
• /
• pp.54-54
• /
• 2003

• Bulletin of the Korean Space Science Society
• /
• 2003.05b
• /
• pp.62-62
• /
• 2003

• Bulletin of the Korean Space Science Society
• /
• 2003.05b
• /
• pp.61-61
• /
• 2003

• Water for future
• /
• v.52 no.11
• /
• pp.16-21
• /
• 2019

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.6
• /
• pp.32-38
• /
• 2009

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.4
• /
• pp.1181-1190
• /
• 2014

In this study, the erosional parameters for deposit beds were quantitatively estimated domestically for the first time through the erosion tests using an annular flume. Four erosion tests were carried out for the deposit beds with different consolidation structures, which were obtained by consolidating the kaolinite slurries for a given time durations. Results of erosion tests showed that the bed shear strength ${\tau}_s$ increased with the consolidation time and bed depth. The erosion rate ${\epsilon}$ was also shown to be related well with the excess shear stress ${\tau}_b-{\tau}_s$ which was given by the difference between flow shear stress ${\tau}_b$ and bed shear strength ${\tau}_s$. While the logarithm of the erosion rate was linearly related with the excess shear stress as ${\tau}_b-{\tau}_s{\geq}0.1N/m^2$, however, the erosion rate decreased rapidly with it when ${\tau}_b-{\tau}_s{\leq}0.1N/m^2$. These erosion test results were also shown to be good enough to verify by comparing with the test results from previous studies and a new equation was suggested to describe the erosion rate more well in the region of ${\tau}_b-{\tau}_s{\leq}0.1N/m^2$.