• Transactions of the Korean Society of Mechanical Engineers
• /
• 제16권11호
• /
• pp.2049-2058
• /
• 1992

In this work, a 6 degree of freedom lumped mass model is constructed for an OHC-type cam valve train analysis, and the model is verified experimentally. Using the verified model, an optimum cam profile is designed to minimize the maximum contact force between cam and follower under the constraints such as cam lift and cam event angle. The designed cam was carefully machined and tested experimentally. As operating the designed cam shaft on the test rig, the valve motion was precisely measured with laser displacement meter and the contact force was indirectly monitored by measuring strain at a certain point of the finger follower. Judging from the model simulation and experiment results, the maximum contact force can be reduced as much as more than 16.7 percent under maintaining the original valve flow area by adopting the optimum cam profile.

• Journal of the Korean Society for Precision Engineering
• /
• 제32권5호
• /
• pp.455-461
• /
• 2015

This paper deals with an experimental verification of a temperature-dependent power loss model of a DC/DC converter in severe temperature conditions. The power loss of a DC/DC converter is obtained by summing the losses by the components constituting the converter including switching elements, diodes, inductors, and capacitors. MIL-STD-810F stipulates that any electronic devices must be operable in the temperature ranging from $-50^{\circ}C$ to $70^{\circ}C$. We summarized the temperature-dependent loss models for the converter components. A SEPIC-type converter is designed and built as a target. Using a constant-temperature chamber, a test rig is set up to measure the power loss of the converter. The experimental results confirm the validity of the loss model within 4.5% error. The model can be useful to predict the efficiency of the converter at the operating temperature, and to provide guidelines in order to improve the efficiency.

• Journal of the Korean Society for Precision Engineering
• /
• 제32권5호
• /
• pp.415-422
• /
• 2015

Ballscrews are important motion transfer and positioning units of industrial machinery and precision machines. Positioning accuracy of the feed drive system depends upon axial stiffness of ballscrew systems. As the nut stiffness depends upon preload and operating conditions, analytical modeling of the stiffness is performed through the contact and body deformation analysis. For accurate contact analysis, the contact angle variation between balls and grooves is incorporated in the developed model. To verify the developed mathematical stiffness model, experiments are conducted on the test-rig. Through the uncertainty analysis according to GUM (Guide to the expression of Uncertainty in Measurement), it is confirmed that the formulated stiffness model has over 85% estimation accuracy. After constructing the ballscrew DB, a quick turnaround system for the nut stiffness estimation has been developed in this research.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• 제15권1호
• /
• pp.19-24
• /
• 2003

The objectives of this paper are to develop a new method of wettability mea-surement and to study the effect of surface roughness on the wettability in a $H_2O$/LiBr falling film absorber. Two absorber tubes with micro-scale roughness and a bare tube are tested in a falling film absorber installed in a test rig. Inlet solution temperature, concentration and mass flow rate are considered as key parameters. A new method is proposed to estimate the wettability of a tube by measuring a minimum mass flow rate to wet the tube completely. The wettability for the structured surfaces was higher than that for the bare tube. The wettability decreased linearly along the vertical location. The wettability increased with increasing the solution temperature and the solution mass flow rate. The experimental correlations of the wettability for the bare and the micro-hatched tubes were developed with error bands of$\pm20%\;and\;\pm10%$, respectively. This work can be used in the design of absorbers with micro-scale roughness.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• 제23권3호
• /
• pp.234-239
• /
• 2013

There are many types of speed reducer for industrial uses. However the cycloid speed reducer is widely used in manipulators based on excellent performance of low backlash, high reduction ratio and compact size. It is essential to use precision speed reducer for accuracy of position controls on robot systems and electric vehicles. The cycloid speed reducer has a eccentric rotating motion and offset to avoid some problem of assembly, so it has a disadvantage for vibration. In this paper, a multi-body dynamic model is developed for a cycloid speed reducer and the dynamic behaviors of the reducer are investigated. The cycloid speed reducer consists of cycloidal plate gears, housing gear, input shaft, output pin and shaft, and eccentric bearings. Using a CAD program, each component of cycloid reducer is modeled based on the offset and eccentric. Multi-body simulations using Recurdyn and test using a rig tester are performed. As a result, the pin reaction force and the amplitude of housing displacement are increased by the larger offset and smaller eccentric value of cycloid reducer.

• Tribology and Lubricants
• /
• 제10권3호
• /
• pp.29-38
• /
• 1994

The friction and wear of mild steel at dry sliding surfaces under different vacuum conditions have been investigated to understand the wear mechanisms. For the test, a ball-ondisk typed wear-rig has been built and implemented, allowing control of sliding speed, load and vacuum. Results show that, at a high sliding velocity, friction of low carbon steel (SS41) under a high vacuum is much higher than that of ambient condition and wear is much severer. It is due to lack of effective oxidation film formation on which steel surfaces could protect themselves against the severe wear. It has been shown, however, that there is a critical regime with contact conditions (at a low sliding velocity, a low load, and under a medium vacuum) at which effective, protective films of low carbon steel have been built on the surfaces in a friction process with a self-regulating way, resulting in both very low coefficients of friction (about 0.3) and mild wear. In order to investigate the protective films on steel surfaces, the worn surfaces and the wear debris have been experimentally analyzed with SEM, AES/SAM and XRD. A theoretical analysis of frictional heating at sliding surfaces, and an experimental analysis of the influence of oxidation wear under various vacuum conditions are described. The important variables on which self-formations of protective films at dry sliding surfaces depend, and the wear mechanisms are also investigated.

• Journal of Ocean Engineering and Technology
• /
• 제24권2호
• /
• pp.1-9
• /
• 2010

Oscillating Water Column is one of the most widely used converting systems all over the world. The operating performance is influenced by the efficiencies of the two converting stages in the OWC chamber-turbine integrated system. In order to study the effects of the pressure drop induced by the air turbine, the experiments using the impulse turbine and the orifice device are carried out in the wave simulator test rig. The numerical simulation utilizing the orifice and porous media modules is calculated and validated by the corresponding experimental data. The numerical wave tank based on the two-phase VOF model embedded with the above modules is employed to investigate the wave elevation, pressure variation inside the chamber and the air flow velocity in the duct. The effects of the air turbine on the integrated system and interaction among the wave elevation, pressure and air flow velocities variations are investigated, which demonstrates that the present numerical model are more accurate to be employed.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• 제24권9호
• /
• pp.2387-2396
• /
• 2000

Wear and operation characteristics of Nylon and Acetal pinion against steel gear were studied to gain a better understanding of their tribological and mechanical behavior. Tests were conducted with power circulating gear test rig under unlubricated conditions. Specific wear rates were measured as a function of applied load and total revolution. The worn tooth surfaces were examined with a profile projector and camera. Nylon pinion showed lower specific wear rates than Acetal pinion, but it revealed breakage at high load. Principal wear depths were developed at tooth tip and below the pitch line of pinion. Life estimation for the Nylon pinion was made by taking into account steel gear equivalent Hertz stress and average sliding velocity. The dominant wear mechanisms were adhesion and abrasion.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• 제24권3호
• /
• pp.320-326
• /
• 2015

Despite the wide industrial applications of planetary gear trains, the relationship between the design parameters (tooth profile, carrier mass, etc.) and performance (strength, vibration, noise, etc.) remains poorly understood. A significant amount of research has focused on transmission errors, which are measurable performance indicators directly related to the design parameters. Herein, an experimental test rig for a single-stage planetary gear set built using digital angular encoders and gap sensors is described. To study the static and dynamic characteristics of this planetary gear train, the transmission errors and sun gear orbit are analyzed from the data measured under various levels of torque and speed. The transmission errors of the gear train decrease 40% when the speed increases from 30 to 600 rpm with an output torque of 39.2 Nm, and increase 22% when the output torque increases from 19.6 to 39.2 Nm with an input speed of 30 rpm.

• Journal of ILASS-Korea
• /
• 제11권3호
• /
• pp.176-189
• /
• 2006

In the present study, capability of improving the liquid atomization of a high-speed liquid jet by using wall impingement is explored, and its application to a jet engine atomize. is demonstrated. Water is injected from a thin nozzle. The liquid jet impinges on a wall positioned close to the nozzle exit, forming a liquid film. The liquid film velocity and the SMD were measured with PDA and LDSA, respectively. It was shown that the SMD of the droplets was determined by the liquid film velocity and impingement angle, regardless of the injection pressure or impingement wall diameter. When the liquid film velocity was smaller than 300m/s, a smaller SMD was obtained, compared with a simple free jet. This wall impingement technique was applied to a conventional air-blasting nozzle for jet engines. A real-size air-blasting burner was installed in a test rig in which three thin holes were made to accommodate liquid injection toward the intermediate ring, as an impingement wall. The air velocity was varied from 41 to 92m/s, and the liquid injection pressure was varied from 0.5 to 7.5 MPa. Combining wall impinging pressure atomization with gas-blasting produces remarkable improvement in atomization, which is contributed by the droplets produced in the pressure atomization mode. Comparison with the previous formulation for conventional gas-blasting atomization is also made, and the effectiveness of utilizing pressure atomization with wall impingement is shown.