• Journal of the Korean Society for Nondestructive Testing
• /
• v.34 no.1
• /
• pp.18-22
• /
• 2014

Residual stresses that occur during the welding process, are the main cause of failure and defects in welded structures. This paper, presents the use of an electronic processing laser speckle interferometer to measure the residual stress of a welded pipe for a nuclear power plant. A tensile testing machine was used to evaluate a welded pipe that failed in compression. The inform plane deformation and modulus of elasticity of the base metal and welds were measured using an interferometer. Varying the load on the welded pipe had a larger effect on the deformation of the base metal the other properties of the base metal and welds. The elastic moduli of the base metal and weld of the welded pipe were 202.46 and 212.14 GPa, respectively, the residual stress was measured to be 6.29 MPa.

• Korean Journal of Materials Research
• /
• v.7 no.1
• /
• pp.50-56
• /
• 1997

급냉응고법을 이용하여 고용한도 이상으로 Mn량을 첨가할 때 Mn량에 따른 인장특성의 변화와 시효특성을 조사하였다. 원심분무법으로 AI-4.7%Zn-2.5%Mg-0.2%Zr합금에 Mn량을 각기 달리 첨가한 급냉응고 분말을 제조 하였다. 이 분말을 냉간압축, 진공 탈가스처리를 한 후 15:1로 압출하여 봉상 시편을 만들었다. 분말의 미세조직은 $\alpha$-AI수지상과 수지상간 편석부로 이루어져 있으며 Mn첨가에 따라 조직의 변화는 관찰되지 않았다. 빠른 냉각속도로 인하여 2.0%Mn을 첨가한 경우에도 초정 Mn상을 발견할 수 없었다. 압출재의 미세조직은 아결정립으로 이루어져 있으며 약간의 제2상들이 관찰되었다. 대부분의 Mn 분산상은 압출후 용체화처리 과정에서 형성되었으며 시효경화량은 Mn양에 관계없이 일정하였다. 46$0^{\circ}C$에서 1시간 용체화처리하고 12$0^{\circ}C$에서 24시간 시효처리한 경우 최대의 시효경도값을 나타내었다. 인장강도는 Mn첨가량에 따라 증가 하였는데 이것은 Mn분산상의 밀도증가에 의한 것으로 확인되었다. 2.0%Mn을 첨가한 합금의 시효후 인장강도는 590MPa, 연산율은 4%를 보였다.

• Journal of Powder Materials
• /
• v.20 no.6
• /
• pp.467-473
• /
• 2013

This research presents a preparation method of dental components by metal injection molding process (MIM process) using titanium scrap. About $20{\mu}m$ sized spherical titanium powders for MIM process were successfully prepared by a novel dehydrogenation and spheroidization method using in-situ radio frequency thermal plasma treatment. The effects of MIM process parameters on the mechanical and biological properties of dental components were investigated and the optimum condition was obtained. After sintering at $1250^{\circ}C$ for 1 hour in vacuum, the hardness and the tensile strength of MIMed titanium components were 289 Hv and 584 MPa, respectively. Prepared titanium dental components were not cytotoxic and they showed a good cell proliferation property.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.16 no.3 s.43
• /
• pp.335-344
• /
• 1992

This study was conducted to investigate the influence of addition of cetyl trimethyl ammo­nium bromide (CTAB), and amine [ethylamine (EA) or ethylene diamine (EDA)] to aqueous sodium hydroxide (NaOH) solution on polyester alkaline hydrolysis, The experimental vari­ables such as CTAB concentration, EA or EDA concentration, NaOH concentration, tempera­ture and time were compared, and the changes in physical and chemical properties of alkaline­hydrolyzed PET fabrics depending on their treated conditions were measured, The results are as follows: 1. By adding CTAB and amine in aqueous NaOH solution, increasing effect on weight loss of PET fabrics was obtained in simultaneous addition of CTAB and EDA, but not in CTAB and EA. 2. By adding CTAB & EDA simultaneously, increasing effect on weight loss was obtained regardless of EDA concentration, time and temperature, and it was more effective at lower NaOH concentration. :l. The increase of void space (or irregularly grooved surface), of softness, of wickability, of dyeability on PET fabric, and the decrease of tensile strength, of molecular weight were observed according to the weight loss on the PET fabrics. These changes were equal to all alkaline-hydrolyzed PET fabrics regardless of addition of CTAB and amine. l. There was little changes on crystallinity, thermal behavior when PET fiber was treated with ,aqueous NaOH solution with CTAB and EDA. These results supported that increasing effect on weight loss take place without inducing of fine structural change of PET fibers.

• Applied Chemistry for Engineering
• /
• v.10 no.2
• /
• pp.299-303
• /
• 1999

In this paper, to investigate the deinkability of domestic and Australian old newsprint according to aging time, two types of newsprint printed with commercial offset ink in domestic(K; Korean newsprint, C; Canadian newsprint), Japanase(J) and Australian(A) old newsprint were aged naturally for 10, 30, 90, 180 days, and then yield, brightness, fiber length, and physical properties (tensile index, tear index, burst index) were evaluated according to aging time. As the aging time increased, the yield and brightness of respective samples decreased. The brightness and yield were decreased in the order of A, K, J and C. The brightness and strength of newsprint varied according to the ink formulation and kinds of pulp and wood. The decreasing order of strength is subsequently J, K, C and A.

• Applied Chemistry for Engineering
• /
• v.10 no.8
• /
• pp.1141-1146
• /
• 1999

Melt blend of PA6/PP-g-MA system containing SEBS-g-MA as a compatible impact modifier was prepared to investigate the change of mechanical properties and morphologies. The tensile strength slightly decreased, but the elongation at break increased with increasing content of SEBS-g-MA in the blend. Also the notched izod impact strength increased with increasing the content of PP-g-MA and SEBS-g-MA. It is attributed to improved compatibilization and interfacial adhesion by reaction of the amide of PA6 with maleic anhydride of SEBS-g-MA and PP-g-MA. The result of dynamic mechanical analysis(DMA) showed a typical behavior of the compatibilization in the polymer blends. Finally, in the phase structure observed by the use of SEM, we confirmed improvement of the compatibilization and interfacial adhesion with increasing the content of SEBS-g-MA and PP-g-MA.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.11 no.6
• /
• pp.87-94
• /
• 2007

Reuse of recycled aggregate from demolished concrete structure is beneficial and necessary from the viewpoint of environmental preservation and effective utilization of resources. The most important mechanical properties of recycled aggregate concrete (RAC) are the compressive strength, the tensile and the flexural strengths, the bond strength and the elastic modulus of such concrete. In particular, the stress-strain relation and fracture process of RAC in compression is especially important in theoretical and numerical analysis as well as engineering design of RAC structures. In this paper, to clarify the characteristics of fracture process in RAC, acoustic emission(AE) method is applied to detect micro-cracking in concrete under compression. From AE parameters, it is found that cracking and fracture behaviors in recycled aggregate concrete fairly differ from that of normal and recycled sand concrete.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.8
• /
• pp.5400-5405
• /
• 2014

For the development of a floating photovoltaic system, materials with light weight and high tensile strength must be applied to reduce the burden on buoyancy, and material characteristics with high resistance to corrosion in water environment is required. Accordingly, a new high strength steel material with improved strength, durability, manufacturability, and weldability that are appropriate for floating photovoltaic system structures is needed. This paper reports the results of a mechanical load test and steel corrosion test on general steel (SS400) and high strength steel (POSH 690) for the selection of an appropriate steel material for a floating photovoltaic system. The results of a test on new high strength steel revealed excellent mechanical performance compared to general steel. The new steel material was manufactured for use in an actual site, and the weight was reduced by approximately 30~40% compared to existing general steel.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.26 no.12
• /
• pp.1701-1708
• /
• 2002

본 연구의 목적은 자외선 차단 가공 처리 및 자외선 조사처리에 의해 면직물의 역학적 특성 변화를 조사하고 가공제 처리조건에 따른 차이점을 분석하는 것이다. 시료로는 100% 면직물을, 자외선 흡수제로 2,2'-dihydroxy-4,4'-dimethoxy benzophenone을, 첨가제로 Triton X-100, polyethylene glycol 400, MgCl$_2$.6$H_2O$를 사용하였다. 자외선 흡수제 처리는 Atlas Launder-O-meter로 75$^{\circ}C$에서 60분간 흡진법으로 하였다. 미처리 시료 및 처리시료는 모두 xenon 램프에 80시간 동안 노출되었으며, 자외선 조사 전후 시료의 역학적 특성은 KES-F시스템을 사용하여 측정하였다. 본 연구의 결과는 다음과 같이 요약할 수 있다. 자외선 흡수제 처리는 처리 농도에 상관없이 면직물의 선형인장성(LT), 인장레질리언스(RT), 굽힘강성(B), 굽힘이력(2HB), 전단강성(G), 전단이력(2HG5), 표면마찰계수(MIU)등을 증가시켰으며 표면거칠기(SMD)는 감소시켰다. 압축특성은 처리농도의 영향을 받아서 고농도의 자외선 흡수제 처리는 압축특성을 감소시켰으며, 저농도의 처리는 압축특성을 증가시켰다. 자외 선 흡수제 처리는 처리농도에 상관없이 면직물의 fullness/softness를 유의하게 증가시키는 반면 stiffness, crispness및 anti-drape stiffness를 감소시켜서 가공포의 종합태(THV)는 가공 전에 비하여 저하하였다. 자외선 조사는 가공 전 면직물의 경우 B, 2HB, G, 2HG, 2HG5, LC를 감소시켰다. 자외선 조사는 처리농도와 상관없이 가공포의 WT, 굽힘특성 , 전단특성을 감소시켰으며, 저농도의 흡수제 처리포의 경우 SMD를 증가시켰으며, 고농도의 흡수제 처리포의 경우 SMD를 감소시켰다. 자외선 조사는 처리농도와 상관없이 가공포의fullness/softness, stiffness, anti-drape stiffness를 유의하게 감소시켜서 자외선 조사 전 보다 THV가 37% 저하하였고 미 가공포의 THV를 저하율보다는 저하가 낮았다. 자외선 흡수제 처리에 의해 면직물의 태는 가공 전보다 감소하지만, 자외선 흡수제 처리는 자외선 조사에 의한 태 감소율을 낮추는 데 유의 한 효과가 있다.

• 한국금형공학회:학술대회논문집
• /
• 2008.06a
• /
• pp.23-26
• /
• 2008

In order to examine the deformation characteristics of Al circular pipe underthe biaxial compression, the horizontal biaxial compression die for the experiment was manufactured. From this, in the various compressive strain rate (1 mm/min. ${\sim}$ 400 mm/min.)conditions, the circular pipes, which were made by Al materials, were investigated based on the properties change of cross section area, punch load and deformation behavior. The tensile and compressive strains were evaluated from micro Vickers hardness tester. From these results, the punch load and deformation characteristic of Al circular pipes were highly changed in the compressive strain rate about 200 mm/min. The Al circular pipes had the tendency that the punch load decreased with increasing the compressive strain rate. In addition, following as the change of the shape and position of neutral axis due to the deformation proceeding of the circular pipe, the special point of the internal circular pipe at maximum load showed the maximum deformation strain and the maximum measured hardness value. The CAE (computer aided engineering) simulation using Deform-2D program was performed on the circular pipe in order to know and verify the exact compressive deformation behavior. From these results, the experimentally measured results were reasonably in good agreement with the simulation results.