• 한국작물학회:학술대회논문집
• /
• 한국작물학회 1983년도 춘계 학술대회지
• /
• pp.4-5
• /
• 1983

• 대한치과보철학회지
• /
• 제31권4호
• /
• pp.468-481
• /
• 1993

The Purpose of this study was to analyze the stresses and displacements of various post and core. The Finite element models of central incisors were divided into seven types according to the various amount of remaining tooth structures. $10kgf/mm^2$ force was applied respectively as follows : 1) Horizontal on the labial surface 2) $26^{\circ}$ diagonal direction on the lingual surface. Material property, geometry, and load condition of each model were inputted to the two dimensional ANSYS 4.4A finite element program : stresses and displacements were analyzed. Results were follows : 1. In the case of $130^{\circ}$ shoulder post and core, Maximum tensile and shear stresses were observed in the crown margin. 2. Maximum shear stress was about 29% reduced by contrabevel. 3. In the case of 1mm axial tooth structure, Maximum tensile stress observed in the dentin. 4. In the case of but joint of cervix, Maximum stress concentration was observed in the dentin by the inclined and horizontal force. 5. Horizontal force produced the extraordinary high stresses in dentin and supporting structures. 6. The amount of remaining tooth structure affected the level of stress significantly and it determined the location of stress concentration.

• 한국치위생학회지
• /
• 제4권2호
• /
• pp.179-191
• /
• 2004

A series of experiments were conducted on dental denture base resins for their antibiosis. They were also compared in terms of physical and mechanical characteristics, which led to the following results: 1. As for bacterial deposition, the old products showed a wide range of distribution, while those products containing C. S. had restraints. 2. Among the products containing C. S., those ones of 7, 12 and 20% all had restraints of similar size to slop further bacterial growth. In the meanwhile, the old products had only small-size restraints for bacterial growth. 3. The following changes were observed in the aspect physical characteristics: There were no significance between the old products and the C. S. products. Thus, as for compressive force, the average${\pm}$standard deviation of the old products was $27.4083.{\pm}1.7397$, and those C. S. products of 20% showed the similar $27.5600{\pm}.1976$. In addition, there were no significance between the old products and those ones containing C. S. in terms of tensile force. The tensile force of the old products was $114.5600{\pm}.8916$ in average${\pm}$standard deviation, while there was no differences among the C. S. products of 7, 12, and 20% in that matter.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2006년도 춘계 학술발표회 논문집
• /
• pp.1303-1311
• /
• 2006

Most of the piles are designed as group piles. In certain geotechnical environments, the installation of group piles causes heaving of the already installed piles. The unfavorable effects of pile heaving on pile bearing capacity have been well known to field engineers. However not many engineers pay enough attention to this subject. According to our recent researches, not only the bearing capacity but also the pile material could be seriously damaged due to the installation of nearby piles, especially with the cases of precast concrete piles. When the pull-out force due to installation of neighboring piles acting on the already installed precast concrete pile exceeds the shaft friction, pile heaving occurs. At the same time, if the pull-out force exceeds the allowable tensile strength of the precast concrete pile, tensile failure is inevitable, which is critical for the pile integrity. In other cases the pile material was not damaged but serious relaxation occurred as the results of pile heaving. In this paper, the pull-out mechanism due to the installation of group piles is explained.

• Journal of Welding and Joining
• /
• 제22권4호
• /
• pp.43-49
• /
• 2004

Conventional method for electrode force application in resistance spot welding(RSW) processes is to use pneumatic cylinder. However, due to its inherent problems in pneumatic power system such as compressibility of air and poor transient response characteristics, new electrode force system with servo control are recently introduced in RSW machine. This machine is called “servogun”. The purpose of this study is to evaluate performance of servogun in case of spot welding of aluminum alloy. Aluminum alloy(A5052) sheets are spot welded using pneumatic gun and servogun. Both results are compared by means of macro cross-section etching test and tensile shear strength test. Numerous previous research have reported nugget with many voids and cracks are not uncommon defects in spot welds with aluminum alloy. The experimental results show similar defects in case of pneumatic gun. In contrast, use of servogun considerably reduced generation of voids and cracks. In case of step-wise increased forging force at the end of welding cycle with servogun, crack-free and void-free nuggets have been observed. The performance of servogun has been also verified by series of tensile shear test. Higher strength values have been achieved with servogun in comparison to that of pneumatic gun.

• Elastomers and Composites
• /
• 제55권4호
• /
• pp.270-276
• /
• 2020

The long-term durability of an FKM O-ring used as parts of a hydrogen station was investigated by exposing it to high-pressure gaseous hydrogen for 1, 3, and 7 days at room temperature. Changes in its sealing force were subsequently measured at 150℃ using intermittent compression stress relaxation (CSR). No changes in the tensile properties of FKM O-ring were observed, but its initial and overall sealing forces at 150℃ significantly decreased with increasing exposure time to hydrogen gas. Microvoid formation in the FKM O-ring upon exposure to high-pressure hydrogen was minimized over time after the ring was exposed to atmospheric pressure at room temperature, which prevented changes in its tensile properties. However, applying heat accelerated FKM O-ring oxidation, which decreased its sealing force. These results indicated that identifying changes in the sealing force of rubber materials using intermittent CSR is not sufficient for monitoring changes in mechanical properties under high-pressure hydrogen atmospheres; however, it is suitable for evaluating the long-term durability of sealing materials for hydrogen station applications under similar conditions.

• International Journal of Safety
• /
• 제11권1호
• /
• pp.19-21
• /
• 2012

In this thesis, fracture test was performed in order to investigate the fracture strength of SFRC(steel fiber reinforced concrete) structures. The relationship between the compressive force and strain value of SFRC specimens were observed under the compressive strength test. From the fracture test results, the relationship between percentage of fiber by volume, compressive strength, elastic modulus, and tensile strength of SFRC beams were studied, and the measured elastic modulus of SFRC were compared with the calculated elastic modulus by ACI committee 544.

• 농업과학연구
• /
• 제9권2호
• /
• pp.569-575
• /
• 1982

수확기간(收穫期間)에 있어서 벼줄기의 물리적(物理的) 및 기계적(機械的) 특성(特性)을 구명(究明)하고져 일반계(一般系) 품종(品種)인 이리(裡里)348 및 진주(晋州)벼와 통일계(統一系) 품종(品種)인 서광벼 및 태백(太白)벼 4개(個) 품종(品種)을 표준시비구(標準施肥區)에서 선정(選定)하여 압축(壓縮), 인장(引張), 굽힘 시험(試驗)을 실시(實施)하고, 이어서 진주(晋州)벼 및 태백(太白)벼에 대(對)하여 부위별(部位別), 전단각도(剪斷角度) 및 함수율(含水率) 변화(變化)에 따른 전단하중(剪斷荷重)-변형특성(變形特性), 전단력(剪斷力) 및 전단(剪斷) energy등(等) 전단특성(剪斷特性)을 측정(測定) 분석(分析)한 결과(結果)는 다음과 같다. 1. 압축(壓縮), 굽힘, 인장(引張) 및 전단력(剪斷力)은 통일계품종(統一系品種)에 비(比)하여 일반계(一般系) 품종(品種)이 컸다. 2. 전(全) 부위별(部位別)의 전단력(剪斷力) 추세는 진주(晋州)벼에 있어서 하부위(下部位)의 큰 값이 상부위(上部位)로 갈수록 감소(減少)하였고, 태백(太白)벼에 있어서는 하부위(下部位)부터 지상(地上) 21cm까지 비교적 일정(一定)한 큰 값으로 나타냈다. 3. 전단면적(剪斷面積)의 증가(增加)에 따라 전단력(剪斷力) 및 전단(剪斷) energy는 증가(增加)하였고, 그 증가율(增加率)은 전단면적(剪斷面積) $10mm^2$까지는 컸으나 그 이상(以上)에서는 매우 둔화(鈍化)되었다. 4. 예취(刈取) 직후(直後)에 있어서 함수율(含水率)의 감소(減少)에 따른 전단력(剪斷力) 및 전단(剪斷)energy의 감소(減少)는 컸으나 함수율(含水率) 60%(w.b)부터는 큰 변화(變化)가 없었다.

• 한국지반신소재학회논문집
• /
• 제16권4호
• /
• pp.113-118
• /
• 2017

확공형 앵커에 대한 인발시 거동 특성을 분석하기 위해 유한요소해석 프로그램을 이용하여 수치해석을 수행하였다. 확공형 앵커에 대한 수치해석 결과에서 확개각도의 변화에 따른 앵커의 지지력 비율 결과값과 앵커의 강선에 작용하는 축하중 결과값의 비교 분석을 통해 확개각도의 크기가 커질수록 앵커의 지지력 증대효과가 나타나는 것을 알 수 있었다. 확개각도가 $30{\sim}60^{\circ}$인 경우 앵커인장력에 따른 변형 및 응력분포 특성은 유사하게 나타났으나 동일한 앵커인장력이 작용할 경우 확개각도에 따라 상부 변위발생량의 차이로 인하여 마찰저항력 발현정도에 차이가 나타남을 볼 수 있었다. 또한, 본 연구에서 적용된 확공형 비트가 상부를 원뿔형으로 굴착함에 따라 그라우팅부 상부 원뿔위치에서 최대압축력과 인장력이 발생하는 것이 확인되었으며, 상부 그라우팅부의 인장파괴가 발생할 가능성이 있음을 알 수 있었다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제12권4호
• /
• pp.71-78
• /
• 2008

철도교량의 경우, 열차하중에 의한 영향으로 교량 단부에서 상향력이 발생하였으며, 이 상향력은 체결장치에 압축력과 인장력을 유발시켰다. 현재까지 이에 대한 안전성을 검토하기 위해 체결장치를 1방향의 스프링 요소로 모사하여 구조해석을 수행해 왔다. 이러한 경우에 스프링 요소의 강성은 압축력을 재하한 실험적 연구에 의하여 산정되었다. 따라서, 상향력은 체결장치에 압축력뿐만 아니라 인장력도 유발시키기 때문에 합리적이고 정확한 구조해석을 수행하기 위해서는 인장력을 재하한 실험적 연구로부터 산정된 병진방향 강성 그리고 회전방향 강성을 함께 고려해야 한다. 본 연구에서는 6가지 실험체에 대하여 탄성과 비탄성 실험을 수행하여 레일 연직방향 병진강성과 레일 강축에 대한 회전강성을 검토하였고, 체결장치의 구조적인 거동을 분석하였다.