• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.14 no.6
• /
• pp.83-87
• /
• 2005

Hardening Constant Velocity joint increases hardness near the surface and the surface improves fatigue life. Although case depth and chemical composition are same, the prior structure of induction hardened Constant Velocity Joint affects the fatigue strength and life during hardening. Therefore torsional fatigue tests of specimens from vaere conducted on induction hardened automotive Constant Velocity joint with various case depths and lrious prior structures, which are obtained by nomalizing, spheriodized annealing and tempering after quenching, woads applied in order to evaluate the relation between prior structure and fatigue strength.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.280-281
• /
• 2006

Powder grades pre-alloyed with 1.5-3 wt% chromium can be successfully sintered at the conventional temperature $1120^{\circ}C$ although well-monitored sintering atmospheres are required to avoid oxidation. Mechanical properties of the Cr-alloyed PM grades are enhanced by a higher sintering temperature in the range $1120-1250^{\circ}C$, due to positive effects from pore rounding, increased density and more effective oxide reduction. Astaloy CrM (Fe-3 wt% Cr-0.5 wt% Mo) with 0.6 wt% graphite added obtains an ultimate tensile strength of 1470 MPa and an impact strength of 31 J at density $7.1\;g/cm^3$, after sintering at $1250^{\circ}C$ followed by cooling at $2.5^{\circ}C/s$ and tempering.

• Proceedings of the KSR Conference
• /
• 1998.11a
• /
• pp.497-504
• /
• 1998

The manufacturing processes of the head hardened rails and the principles of the heat treatment for carbon steels are introduced in this paper, To get the good wear resistance of the rail, many kinds of microstructure had been developed for the rail head hardening. One of these is the tempered martensitic structure, which is very hard but brittle because of Quenching-Tempering Process. Another is the fine pearlitic structure by Slack Quenching. Now Banitic structure steels are emerging as a potential new material to replace eutectoid pearlitic steels for rail. The main reason of this change is due to the limitaion of pearlitic microstructure with regard to mechanical properties and wear resistances of railway rails.

• Journal of Conservation Science
• /
• v.34 no.3
• /
• pp.179-193
• /
• 2018

This study is aimed to investigate the provenance of raw materials and firing temperature of jar coffins excavated from the Oryang-dong kiln site and Jeonchon tomb site, Naju, Korea. Most of jar coffin samples shows same range of magnetic susceptibility and have gray color, while 404 and 405 of Jeongchon site are reddish yellow. In some samples fired at high temperature, the water absorption at the mouth rim and body part of same jar coffin were 3.50% and 7.56% respectively. It means that heat transfer and equilibrium in the kiln was not properly continued and the heat energy transferred to the mouth rim and the body part was different. In the petrographic analysis, As a tempering materials, biotite, weathered quartz and feldspar were added in the jar coffins of Oryang-dong site, and biotite, polycrystalline quartz and feldspar in it of Jeongchon site. Tempering materials were found more in the body than in the mouth rim of same jar coffin of Oryang-dong site. It seemed that some samples were fired at over 1,000 to $1,100^{\circ}C$, which showed vitrified texture in the scanning electron images and the rest of samples were fired at below $900^{\circ}C$. Due to similarity of chemical compositions, it is estimated that jar coffins of Jeongchon tomb were produced and supplied from Oryang-dong kiln site. However, the slight difference of some trace elements distribution of samples is attributed to the selection of clay depending on the location.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.5
• /
• pp.252-261
• /
• 2017

This study examined the effect of heat treatment on the microstructure and mechanical properties of J55 line pipe steel. The experiments were carried out at under the following various conditions: austenization temperature($880^{\circ}C$, $910^{\circ}C$, $940^{\circ}C$), cooling methods(water quenching, oil quenching) and tempering temperature(none, $550^{\circ}C$, $650^{\circ}C$). The phase diagram and CCT curve were simulated based on the chemical composition of J55 steel to predict the microstructures. In the results, A1, A3 temperature decreased. As the austenization temperature increased, existing austenite grains grew exponentially which seriously degraded their mechanical properties. Various microstructures, including martensite, bainite, ferrite, and pearlite, developed in accordance with the heat treatments and were closely correlated with hardness, tensile strength and toughness. Martensite was formed after water quenching, but bainite and ferrite appeared after oil quenching. FeC precipitation formed and coarsened during tempering, which improved their toughness.

• Korean Journal of Materials Research
• /
• v.10 no.6
• /
• pp.409-414
• /
• 2000

Three different white cast irons alloyed with Cr, V, Mo and W were prepared in order to study their transformation behavior of matrix structures in heat-treated conditions. The specimens were produced using a 15kg-capacity high frequency induction furnace. Melts were super-heated to $1600^{\circ}C$, and poured at $1550^{\circ}C$ into Y-block pepset molds. Three combinations of the alloying elements were selected so as to obtain the different types of carbides and matrix structures : 3%C-10%Cr-5%Mo-5%W(alloy No. 1), 3%C-10%V-5%Mo-5%W(alloy No. 2) and 3%C-17%Cr-3%V(alloy No. 3). The heat-treatments were conducted as follows: frist of all, as-cast specimens were homogenized at $950^{\circ}C$ for 5h under the vacuum atmosphere. Then, they were austenitized at $1050^{\circ}C$ for 2h and followed by air-hardening in air. The air-hardened specimens were tempered at $300^{\circ}C$ for 3h. The observation of morphology of the matrix structures was carried out in the states of as-cast(AS), air-hardened(AHF) and tempered(AHFT). The matrix structures of each alloy were almost fully pearlitic in the as-cast state but it was transformed to martensite, tempered martensite and retained austenite by the heat-treatments such as air-hardening and tempering.

• Korean Journal of Materials Research
• /
• v.10 no.11
• /
• pp.760-769
• /
• 2000

Mechanical properties of HSLA cast steels alloyed with 0.15% Nb, Ti or V were tested as variations of austenizing temperatures and tempering times. The test results are as follows. The hardness of HSLA cast steels austenized for 2hrs at 115$0^{\circ}C$ was shown the highest value regardless of alloying elements and then decreased as the temperature decreased below 110$0^{\circ}C$. The hardness of HSLA cast steels with 0.15% Ti austenized for 2 hrs at $1150^{\circ}C$ was higher than that of any other HSLA cast steels, and chich was mainly attributed to the relatively high amount of bainite, and solid solution hardening. Charpy impact energy of HSLA cast steels was comparable to the C-Mn cast steel except HSLA cast steels with 0.15% Ti austenized at 115$0^{\circ}C$. The hardness of HSLA cast steels austenized for 2 hrs at $1150^{\circ}C$ increased at a ten-minute tempering, and after that, the hardness kept almost sililar level except HSLA cast steels with 0.15% V.

• Composites Research
• /
• v.34 no.5
• /
• pp.311-316
• /
• 2021

In this study, TiC/steel metal matrix composites were fabricated by powder metallurgy process using Fealloy powders with 3 wt.% Cr and 10 wt.% Cr, respectively, as matrix material. Subsequently, the composite samples were heat treated by the annealing and quenching-tempering(Q-T), respectively, to understand the effect of heat treatment on the mechanical properties of the composites. The correlation between microstructure and structural strength depending on the chromium content and the heat treatment conditions was studied through tensile, compressive, and transverse rupture test and microstructural analysis. In the case of TiC/steel composite containing 10 wt.% Cr, the tensile strength and transverse rupture strength at room temperature were significantly lowered by the influence of coarse chromium carbide formed at the TiC/steel interface. On the other hand, both TiC/steel composites containing 3 wt.% Cr and 10 wt.% Cr showed much higher compressive strength of about 4 GP after quenching-tempering compared to the annealed specimens regardless of the presence of the chromium carbide.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2022.10a
• /
• pp.298-298
• /
• 2022

Milling is an important process that determines the quality of flour and is affected by milling machine type, scale, and tempering conditions. In addition, seed hardness is an important factor in determining the amount of tempering water and has been reported to affects flour yield and flour quality. There are reports that vitreousity is used as a measure to distinguish between soft and hard seeds, and the higher the vitreousity, the higher the protein contents. However, there is no established system for measuring viterousity of seeds and studies on the vitreousity and quality characteristics of flour are insufficient. Therefore, in this study, vitreousity, hardness, and milling characteristics were evaluated for 46 major domestic varieties, and their relationship was confirmed. After cutting the seeds using a seed cutter, vitreousity was measured, and seed hardness and flour particle size was measured using SKCS and PSI, respectively. As for the seed hardness index, 'Joa' was the lowest with 11.6, 'Yeonbaek' was the highest with 78.7. As for the milling yield, 'Saeol' had the lowest at 58.1%, and 'Hcjoong' had the highest at 88.6%. Seed hardness index and wheat flour production showed a high positively correlation, showing a similar to that of previous studies. Also, in flour particle size, 'Gobun' was the largest at 75.5 pm, and 'Joa' was the smallest at 43.1 um. Flour yield and flour particle size showed a high positively correlation. As a result of vitreousity, 'Hwangeumal' (55.2%), 'Saekeumkang' (59.1%), 'Baekkang' (52.3%), 'Goso' (44.6%), and 'Joa' (19.2%) were showed. Seed hardness and vitreousity showed a high positively correlation. Also as the vitreousity increased, the flour yield also showed a tendency to increase. In addition, as the seed hardness increased, particle size of the flour yield also showed a tendency to increase. It is thought that this result can be used as a measure to determine the quality of flour with vitreousity. However, further analysis of wheat varieties and methods of analyzing vitreousity are needed.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.431-434
• /
• 2008

In the present study, direct quenching of alloyed steel after hot forging was simulated using commercial finite element program, $FORGE^{TM}$. A typical heat treatment of alloyed steels consists of quenching for hard martensite and subsequent tempering for toughness. In the practice, forgings which cool down to room temperature are heated to temperature of austenite regime. As investigated in the present study, direct quenching of hot forged stock would be beneficial in terms of energy saving. This process has already been propose and termed as ausforging or forged hardening. However, it is well known that quenching temperature would be the most critical factor to control heat treated forging properties. And it is very difficult to control quenching temperature when forged stock gets directly quenched after forging. In this study, we have calculated final forging temperature of stock. Also, quenching simulation was conducted using a series of material parameter which were also calculated using JMATpro, a commercial program for physical properties of materials.