• 공업화학
• /
• 제17권1호
• /
• pp.33-36
• /
• 2006

광경화 접착제로 많이 사용되는 우레탄-아크릴레이트 올리고머의 광경화 거동을 자체촉매화 반응모델식을 통해 중합온도 및 올리고머의 관능성에 따른 영향을 확인하여 보았다. 중합온도가 증가함에 따라 최대중합속도는 감소하여 중합온도가 경화 거동에 대한 영향인자임을 확인할 수 있었으며, 반응속도상수 k는 온도증가에 따라 거의 일정한 값을 보이나 반응차수 m과 n은 증가하는 경향을 보였는데 이는 가교구조에 의한 반응성 기의 확산제한 및 유동성의 제한으로 인한 것으로 판단되어진다. 온도증가에 따른 중합속도의 감소는 주로 반응차수 n의 증가에 의해 진행되었다.

• 수산해양기술연구
• /
• 제28권1호
• /
• pp.45-52
• /
• 1992

In this paper, combustion characteristics and engine performance varying with blending rate of fish oil using five test fuels, e.g.pure diesel oil and four types of sardine-oil-blended diesel oils, their blending rates by weight being 20%, 40%, 60% and 80% respectively, and operating condition of engine, were investigated experimentally both in the constant volume combustion bomb and in the engine. The results are summarized as follows: 1) In the bomb, the influence of temperature on ignition delay of sardine-oil-blended diesel oils was larger than that of pure diesel oil, and it tended to increase as the blending rate of fish oil increase sardine-oil-blended diesel oils. As far as the influence of pressure on ignition delay concerns, there was no significant difference with all the test fuels. 2) In the engine, the ignition delay of fish-oil- blended diesel oils was longer than that of pure diesel oil, and it tended to increase as the blending rate increases. In the bomb, the ignition delay in high temperature showed no significant difference between with pure diesel oil and with fish-oil-blended diesel oils, and it was especially short with 60% fish-oil-blended diesel oil. In low temperature, however, the delay became longer as the blending rate increase. 3) The combustion duration was shorter with fish-oil-blended diesel oils than with pure diesel oil and it became a little shorter as the blending rate increases. 4) The rate of fuel consumption showed no significant difference between with fish-oil-blended diesel oils and with prue diesel oil, although calorific value of fish oil was lower than that of diesel oil. 5) Smoke density in exhaust gas was lower with fish-oil-blended diesel oils than with pure diesel oil and the higher the blending rate was, the lower the smoke density became.

• 동력기계공학회지
• /
• 제9권4호
• /
• pp.11-17
• /
• 2005

This paper reports an experimental study on the performance evaluation of air-to-air heat exchanger with rotary type newly developed in this study. Air flow rate is varied from 10 to 120 m3/h. The range of RPM of the porous rotating discs mounted inside the heat exchanger unit is 0 to 50. The temperature of the return air side is set by adjusting heat supply at heater. The material of the porous rotating discs is cooper and its thickness is 1.0 mm. The heat transfer rate increased with the increase in air flow rate. It was found that the heat transfer rate, as the temperature of the return air side was increased, was improved due to higher temperature difference. The heat exchange performance increased with the increase in the temperature of the return air side at the conditions of the same RPM. The sensible heat exchange efficiency was maximum 68 to 76 percent, and enthalpy exchange efficiency 64 to 74 percent.

• 한국산학기술학회논문지
• /
• 제19권8호
• /
• pp.32-36
• /
• 2018

500kgf 용량의 Instron 시험기를 이용하여 폴리프로필렌 판재의 인장시험 평가를 행하였다. 두께가 0.8 mm인 폴리프로필렌 판재의 변형속도민감도를 평가하기 위하여 변형속도는 $5{\times}10^{-4}/sec{\sim}5{\times}10^{-2}/sec$으로 100배 변화를 주어 상온 및 고온인장시험 하였다. 이를 통하여 변형속도 및 온도 변화에 따른 강도변화를 비교하였다. 실험결과 초기 변형속도가 증가할수록 강도가 증가하였으며 이는 폴리프로필렌은 변형속도민감도가 강한 양의 값을 지닌 재료임을 알 수 있었다. 또한 폴리프로필렌 판재의 고온 인장특성을 평가하기 위하여 온도는 80, 120, $160^{\circ}C$로 변화시켜 시험하였다. 고온인장시험 결과 온도가 증가할수록 강도는 감소하였으며 특히 $160^{\circ}C$에서는 강도가 인장강도가 0으로 강하하였다. 변형속도 증가에 따른 온도 증가의 영향을 살펴보면 상온, $80^{\circ}C$ 및 $120^{\circ}C$까지는 항복강도 및 인장강도의 증가 폭이 비슷한 수준을 나타내었으나 $160^{\circ}C$에서는 응력이 0에 가까워짐에 따라 강도 증가가 거의 없는 것으로 나타났다. 고온 인장시험에서 변형속도 증가에 따라 항복강도 값이 증가하는 양 보다는 인장강도 값이 증가하는 폭이 컸다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.175-180
• /
• 2001

In this study, the minimum heat flux conditions are experimentally investigated for the spray cooling of hot plate. The hot plates are cooled down from the initial temperature of about $900^{\circ}C$, and the local heat flux and surface temperatures are calculated from the measured temperature-time history. The results show that the minimum heat flux point temperatures increase linearly resulting from the propagation of wetting front with the increase of the distance from the stagnation point of spray flow. However, in the wall region, the minimum heat flux point temperature becomes independent of the distance. Also, the experimental results show that the velocity of wetting front increases with the increase of the droplet flow rate.

• 설비공학논문집
• /
• 제13권10호
• /
• pp.974-981
• /
• 2001

In this study, the minimum heat flux conditions are experimentally investigated for the spray cooling of hot plate. The hot plates are cooled down from the initial temperature of about$ 900^{\circ}C$, and the local heat flux and surface temperatures are calculated from the measured temperature-time history. The results show that the minimum heat flux point temperatures increase linearly resulting from the propagation of wetting front with the increase of the distance from the stagnation point of spray flow. However, in the wall region, the minimum heat flux point temperature becomes independent of the distance. Also, the velocity of wetting front increases with the increase of the droplet flow rate.

• 한국환경보건학회지
• /
• 제17권2호
• /
• pp.41-47
• /
• 1991

A study on the effects of volumetric loading rate, surface loading rate and hydraulic. retention time (HRT) for the anaerobic treatment was conducted with the anaerobic fixed-film process using synthetic wastewater at lower temperature than that of conventional anaerobic treatment. The results are as follows 1. Alkalinity and pH value decreased as the hydraulic retention time increased 2. Increase of the volumetric lodaing rate led to increasl of effluent COD concentration and decrease of COD removal efficiency. 3. The removed volumetric loading rate increased linearly according to the increase of the volumrtric loading rate. 4. Similarly, the linear increase of the removed surface loading rate was noticed with an increase of the surface loading rate.

• 한국식품영양과학회지
• /
• 제26권6호
• /
• pp.1021-1027
• /
• 1997

$CO_2$production in fermentation of dongchimi was measured and interrelated with changes in pH and titratable acidity. The effects of salt content and temperature on $CO_2$production rate were analysed. Fermentation of dongchimi showed drastic pH decrease in early stage and subsequent levelling off around 3.9, with linearly increased acidity up to 0.3~0.4% optimum quality. $CO_2$production of dongchimi could be analysed to consist of two consecutive stages of constant rate. The first stage $CO_2$production of higher rate moved to the second stage of lower rate when acidity rose beyond 0.3%. When compared to those of 1 and 2% salt content, dongchimi of 3% salt showed lower $CO_2$production rate in the 1st stage and slower acidity change through the whole fermentation period. However, it resulted in the product of highest $CO_2$accumulation at optimal ripeness because of consistent $CO_2$production of longer 1st stage period and relatively high $CO_2$production rate in 2nd stage. $CO_2$production depended on temperature less compared to acidity change(activation energy: 57.3 and 44.3kJ/mol for $CO_2$production of 1st and 2nd stages, respectively; 79.3kJ/mol for acidity change), which means higher ratio of $CO_2$production rate relative to acidity increase at lower temperature. Slower increase in acidity at low temperature also was shown to extend the period of 1st stage $CO_2$production. Therefore, low temperature fermentation was effective in producing the high $CO_2$content dongchimi at adequate acidity, which is desirable organoleptically.

• Asian-Australasian Journal of Animal Sciences
• /
• 제28권7호
• /
• pp.943-950
• /
• 2015

Heat stress has adverse effects on fertility of dairy animals. Decline in fertility is linearly associated with an increase in combination of both temperature and humidity. The purpose of this study was to investigate the relationship between temperature humidity index (THI) and the pregnancy rate of Murrah buffaloes in a subtropical climate. The effects of genetic and non-genetic factors viz., sire, parity, period of calving and age group at first calving were found non-significant on pregnancy rate. The effect of THI was found significant (p<0.001) on pregnancy rate of Murrah buffaloes calved for first time and overall pregnancy rate. The threshold THI affecting the pregnancy rate was identified as THI 75. The months from October to March showed THI<75 and considered as non heat stress zone (NHSZ), while months from April to September were determined as heat stress zone (HSZ) with $THI{\geq}75$. The lowest overall pregnancy rate (0.25) was obtained in July with THI 80.9, while the highest overall pregnancy rate (0.59) was found in November with THI 66.1. May and June were identified as critical heat stress zone (CHSZ) within the HSZ with maximum decline (-7%) in pregnancy rate with per unit increase in THI. The highest overall pregnancy rate was estimated as 0.45 in NHSZ with THI value 56.7 to 73.2. The pregnancy rate was found to have declined to 0.28 in HSZ with THI 73.5 to 83.7. However, the lowest pregnancy rate was estimated as 0.27 in CHSZ with THI value 80.3 to 81.6.

• 임산에너지
• /
• 제22권1호
• /
• pp.24-29
• /
• 2003

낙엽송 간벌재 톱밥보드로 우드세라믹을 제조한 후 수지함침율 및 소성온도에 따른 우드세라믹의 표면온도 변화를 조사하였다. 히터의 표면온도가 증가함에 따라 우드세라믹의 표면온도도 급속히 증가하였으며 수지함침율 70∼80%, 소성온도 800∼1000℃ 조건으로 제조된 우드세라믹의 표면 온도가 상대적으로 높았다. 히터의 표면온도보다 우드세라믹 표면온도의 하강속도가 느려 우드세라믹이 오랜 시간 열을 유지하고 있음을 알 수 있었다.