• Korean Journal of Optics and Photonics
• /
• v.19 no.3
• /
• pp.224-228
• /
• 2008

A highly sensitive integrated photonic temperature sensor was proposed and developed incorporating a polymeric microring resonator. The change in the ambient temperature was estimated by observing the shift in the resonant wavelength of the resonator induced via the thermooptic effect. For the purpose of enhancing its sensitivity, the sensor was built by implementing a polymeric resonator exhibiting a high thermooptic coefficient on a silicon substrate with a small coefficient of thermal expansion. For the range of from $20^{\circ}C$ to $30^{\circ}C$ near the room temperature, the fabricated sensor yielded a sensitivity of as high as 165 ${\pm}/^{\circ}C$ and a resolution of better than $0.1^{\circ}C$. And its performance was found to be hardly affected by the variation in the refractive index of the target analyte, which was applied to the surface of the sensor. It is hence expected that the sensor could be integrated with other refractormetric optical sensors, thereby compensating for the fatal error caused by the change in the ambient temperature.

• Advances in environmental research
• /
• v.3 no.4
• /
• pp.307-319
• /
• 2014

Four chickpea cultivars viz. kabuli (Pusa 1088 and Pusa 1053) and desi (Pusa 1103 and Pusa 547) differing in sensitivity to high temperature conditions were analyzed in earthern pot (30 cm) at different stages of growth and development in the year of 2010 and 2011. Pusa-1053 (kabuli type) showed maximum photosynthetic rate and least by Pusa-547 (desi type), whereas maximum cell membrane thermostability were recorded in Pusa-1103 and minimum in Pusa-1088. Among the treatments, the plants grown under elevated temperature conditions had produced 13.01% more significant data in comparison to plants grown under continuous natural conditions. Stomatal conductance were reduced 44.25% under elevated temperature conditions than natural conditions, whereas 35.56%, when plants grown under initially natural conditions upto 30DAS, then 30-60DAS elevated temperature and finally shifted to natural conditions till harvest. In case of Pusa-1103, stomatal conductance was maximum as compared to rest of 2.7% from Pusa-1053, 8.9% from Pusa-1088, and 10.3% in Pusa-547 throughout the study. Plants grown under continuous elevated temperature conditions had produced 15.30% and 15.32% more significant membrane thermostability index in comparison to continuous natural conditions at vegetative stage and 19.40% and 18.44% at flowering stage, while the better response was recorded at pod formation stage. Pusa-1053 had given 2.8% more membrane thermostability index than Pusa-1088 and Pusa-1103 had given 1.6% more membrane thermostability index than Pusa-547 in the present study. The membrane disruption caused by high temperature may alter water ion and inorganic solutes movement, photosynthesis and respiration. Thus, thermostability of the cell membrane depends on the degree of the electrolyte leakage.

• The Journal of Korean Obstetrics and Gynecology
• /
• v.24 no.3
• /
• pp.195-202
• /
• 2011

Purpose: The purpose of this study is to report the effect of Traditional Korean Medicine(TKM) on cold sensitivity of hands and feet. And we wanted that cold sensitivity of hands and feet was measured objectively and diagnosed definitely using Digital Infrared Thermographic Imaging(DITI). Methods: The patient in this case was a 29-year-old female. The chief complaint was cold sensitivity of hands and feet. We treated her by TKM and evaluated the progress of symptoms by DITI. And then we compared DITI before treatment and after treatment. Results: After TKM treatment, the differences of temperature of hands and feet were decreased on DITI, respectively. Conclusion: TKM treatment is effective on cold sensitivity of hands and feet. And DITI would be valid to measure for treatment's effect of cold sensitivity of hands and feet.

• Atmosphere
• /
• v.20 no.3
• /
• pp.287-306
• /
• 2010

An ensemble Kalman filter (EnKF) with Weather Research and Forecasting (WRF) Model is applied for Typhoon Wukong (200610) to investigate the performance of ensemble forecasts depending on experimental configurations of the EnKF. In addition, the ensemble sensitivity analysis is applied to the forecast and analysis ensembles generated in EnKF, to investigate the possibility of using the ensemble sensitivity analysis as the adaptive observation guidance. Various experimental configurations are tested by changing model error, ensemble size, assimilation time window, covariance relaxation, and covariance localization in EnKF. First of all, experiments using different physical parameterization scheme for each ensemble member show less root mean square error compared to those using single physics for all the forecast ensemble members, which implies that considering the model error is beneficial to get better forecasts. A larger number of ensembles are also beneficial than a smaller number of ensembles. For the assimilation time window, the experiment using less frequent window shows better results than that using more frequent window, which is associated with the availability of observational data in this study. Therefore, incorporating model error, larger ensemble size, and less frequent assimilation window into the EnKF is beneficial to get better prediction of Typhoon Wukong (200610). The covariance relaxation and localization are relatively less beneficial to the forecasts compared to those factors mentioned above. The ensemble sensitivity analysis shows that the sensitive regions for adaptive observations can be determined by the sensitivity of the forecast measure of interest to the initial ensembles. In addition, the sensitivities calculated by the ensemble sensitivity analysis can be explained by dynamical relationships established among wind, temperature, and pressure.

• Journal of Sensor Science and Technology
• /
• v.6 no.1
• /
• pp.43-48
• /
• 1997

$Ca_{10}(PO_{4})_{6}(OH)_{2}$ humidity-sensitive devices were fabricated by a solid reaction method, and their humidity-sensitive characteristics were investigated. The impedance decreases with increasing relative humidity, and the good sensitivity is shown in which impedance changes by about $10^{2}\;{\Omega}$ over the region of $30{\sim}90\;%$. Also, It is shown that the humidity sensitivity is stable in temperature variations and long time exposures to the humidity. The sensitivity of the specimens is not affected by a heat treatment, and the hysteresis in one humidity cycle is negligible.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.413-414
• /
• 2002

An automotive wheel bearing is one of the most important components to guarantee the service life of a passenger car. The endurance life of a bearing is affected by many parameters such as material properties, heat treatment, lubrication conditions temperature loading conditions, bearing geometry, internal clearance and so on. In this paper, we calculate the endurance life of wheel bearing units and analyze the sensitivity of bearing geometric parameters on the life by using Taguchi method.

• Fire Science and Engineering
• /
• v.9 no.1
• /
• pp.20-29
• /
• 1995

The sprinkler head is a component of the sprinkler system intended to discharge water for automatic detection and extinguishment of fires. On this study, thermal characteristic values affecting the sensitivity of the fusible alloy type sprinkler head were obtained and analyzed under heated air stream condition which had constant temperature and velocity. The experiment was carried out under the forced convection condition with both the conductive heat loss considered and neglected. The thermal characteristic values of the sprinkler head were obtained in accordance with the material and shape of the heat responsive element and the conditions of the main body.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.656-661
• /
• 2005

An optimization formulation of unconstrained damping treatment on beams is proposed to minimize vibration responses using a numerical search method. The fractional derivative model is combined with RUK's equivalent stiffness approach in order to represent nonlinearity of complex modulus of damping materials with frequency and temperature. The loss factors of partially covered unconstrained beam are calculated by the modal strain energy method. Vibration responses are calculated by using the modal superposition method, and of which design sensitivity formula with respect to damping layout is derived analytically. Plugging the sensitivity formula into optimization software, we can determine optimally damping treatment region that gives minimum forced response under a given boundary condition. A numerical example shows that the proposed method is very effective in minimizing vibration responses with unconstrained damping layer treatment.

• Journal of Microbiology and Biotechnology
• /
• v.20 no.2
• /
• pp.287-293
• /
• 2010

Reliable discrimination of a single nucleotide mismatch was demonstrated using arrays with peptide nucleic acid (PNA) probes. The newly developed PNA probes immobilization method and hybridization conditions for PNA arrays gave excellent specificity and sensitivity. In addition we compared the specificity, sensitivity, and stability obtained with the PNA and DNA arrays in discriminating single nucleotide mismatches. The PNA arrays had superior perfect match-to-mismatch signal ratios and sensitivities. The relative signal intensities of mismatch PNA probes ranged from 1.6% to 12.1% of the perfect-match PNA probes. These results demonstrated that the PNA arrays were 2.0 to 37.3 times more specific and about 10 times more sensitive than DNA arrays. The PNA array showed the same specificity and sensitivity after 12-month storage at room temperature.

• Fibers and Polymers
• /
• v.2 no.1
• /
• pp.140-143
• /
• 2001

To better understand the formation of necking in drawing processes of fibers, strain distributions during drawing processes have been analyzed. For simplicity, one-dimensional incompressible steady flow at a constant temperature was assumed and quasi-static model was used. To describe mechanical properties of solid polymers, non-linear visco-plastic material properties were assumed using the power law type hardening and rate-sensitive equation. The effects of various parameters on the neck formation were matematically analyzed. As material property parameters, strain-hardening parameter, visco-elastic coefficient and strain-rate sensitivity were considered and, for process parameters, the drawing ratio and the process length were considered. It was found that rate-insensitive materials do not reach a steady flow state and the rate-sensitivity plays a key role to have a steady flow. Also, the neck formation is mainly affected by material properties, especially for the quasi-static model. If the process length changes, the strain distribution was found to be proportionally re-distributed along the process line by the factor of the total length change.