• Carbon letters
• /
• v.12 no.4
• /
• pp.252-255
• /
• 2011

Carbon-based electric double-layer capacitors are being evaluated as potential energy-storage devices in an expanding number of applications. In this study, samples of carbon black (CB) treated at different temperatures ranging from $650^{\circ}C$ to $1100^{\circ}C$ were used as electrodes to improve the efficiency of a capacitor. The surface properties of the heat-treated CB samples were characterized by X-ray photoelectron spectroscopy and X-ray diffraction. The effect of the heat-treatment temperature on the electrochemical behaviors was investigated by cyclic voltammetry and in galvanostatic charge-discharge experiments. The experimental results showed that the crystallinity of the CBs increased as the heat-treatment temperature increased. In addition, the specific capacitance of the CBs was found to increase with the increase in the heat-treatment temperature. The maximum specific capacitance was 165 $F{\cdot}g-1$ for the CB sample treated at $1000^{\circ}C$.

• Journal of the Korean Ceramic Society
• /
• v.30 no.2
• /
• pp.148-156
• /
• 1993

TiN films were deposited onto high speed steel (SKH9) by plasma assisted chemical vapor deposition (PACVD) using a TiCl4/N2/H2/Ar gas mixture at around 50$0^{\circ}C$. The effects of the deposition temperature, R.F. power and TiCl4 concentration on the deposition of TiN and the microhardness of TiN film were investigated. The crystallinity and the microhardness of TiN films were improved with increase of the deposition temperature. Optimum deposition temperature in this study was 50$0^{\circ}C$, because a softening or phase transformation of the substrate occurred over 50$0^{\circ}C$. A large increase of the film growth rate with a strong(200) preferred orientation was obtained by increasing R.F. power. Much chlorine content of about 10at.% was found in the deposited films and resulted in relatively low average microhardness of about 1, 500Kgf/$\textrm{mm}^2$ compared with the theoretical value(~2, 000Kgf/$\textrm{mm}^2$).

• Journal of the Korean Ceramic Society
• /
• v.32 no.1
• /
• pp.1-10
• /
• 1995

Effects of calcination temperature on microstructure and electric-magnetic properties of Mg-ferrite were investigated. As the calcination temperature increase, the green density and the sintered density increase due to the enhancement of densification of calcined powder. The grain size in the sintered ferrite increases with increasing the calcination temperatures from 800 to 100$0^{\circ}C$, but decreases from 1000 to 120$0^{\circ}C$. The resistivity decreases with increasing the calcination temperatures from 800 to 110$0^{\circ}C$, but increases from 1100 to 120$0^{\circ}C$ due to the microstructure which consists of small, uniform grian size and pores at grain boundaries. Magnetization increases slightly due to the increasement of the sintered density while Curie temperature is almost constant regardless of calcination temperatures.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.525-530
• /
• 2003

Recently an automobile industry is concerned about an automobile wiring harness system. It means that development of component modules is on the increase. An importance of the connector in one part of the modules will be enhanced. A connector is made of P.B.T. (Poly Butylene Terephthalate). PBT is resistant to the high temperature. This paper deals with thermal strain of connector. According as temperature increase, effects of the temperature and thermal strains give an analysis of the deformation using ABAQUS. This apparent thermal strain results actually from the variation of temperature. Being based on this analysis, axiomatic design applies to design parameters of the connector. As compared with CAE analysis, a performance improvement makes certain of the truth of the matter.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.39 no.5
• /
• pp.7-11
• /
• 2007

Kraft pulping of Trema orientalis (Nalita) was studied in order to find kinetic data for delignification. Pulping runs were carried out in the temperature range of $160-180\;^{\circ}C$ under constant and well-defined conditions. The delignification was found to be first order with respect to residual lignin and was chemically controlled. The rate of delignification reaction was increased 1.11-1.23 for $10\;^{\circ}C$ temperature increase in the range of $160-180\;^{\circ}C$ range. A mean value of 93% of lignin was removed at the transition between bulk and residual delignification. The influence of cooking temperature on the rate constant was expressed by an Arrhenius-type equation. The obtained activation energy of the delignification reaction was 6,164 cal/mol. The transition point between bulk and residual phase was shifted to lower lignin and carbohydrate yield with the increase of temperature.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.322-327
• /
• 2000

Natural convection heat transfer in an enclosure with an opening in the right vertical wall and a heat source at the bottom surface is investigated using a holographic interferometric technique. The effects of the opening length, divider length attached to the top wall, and heater temperature on the temperature distribution are examined. The openging length as well as the divider length greatly affects the degree of inflow and outflow of air. With a small opening, the opening doesn't affect much the upward warm air flow resulting in the symmetric temperature distribution. On the other hand, with the increase of the opening length, the inward cold flow moves the upward flow to the left direction. With the increase of the divider length, temperature in the lower region of enclosure becomes higher for the small opening and lower for the large opening.

• Textile Coloration and Finishing
• /
• v.20 no.1
• /
• pp.36-43
• /
• 2008

False twist texturing uses the thermoplastic property of synthetic yarn and produces a bulk and a stretch by giving the filament a permanent crimp. This study investigated the effects of false twist texturing parameters, disk/yarn(D/Y) and heater temperature, on the physical properties of nylon textured yarn. D/Y was a primary determinant of twist numbers of filaments and was proportionally increased with the twist numbers of filaments, resulting in an increase of crimp rigidity of the textured yarn. Heater temperature, a determinant of the heat setting of transformed filaments, was proportionally increased with the increase of crimp rigidity. Nylon 6 was partially melted at $190^{\circ}C$. This study consequently suggested the optimal parameters of nylon 6 85d/68f full-dull POY.

• Journal of the Korean Home Economics Association
• /
• v.24 no.3
• /
• pp.59-67
• /
• 1986

The heat of sewing needle is generated through the friction during the needle penetration into and withdrawal from fabrics. Therefore, effects of sewing condition for knitted fabric on the heat generation of needle was examined. The needle size was not the large influence factor of heat generation of needle but the needle point shape significantly affects needle temperature. And the super needle coated with fluoro resin had more effect on reducing the heat of needle. The decrease of sewing speed and the increase of stitch rate had more effect on the reduction in needle temperature. Also the Influence of a sewing thread on the needle temperature was very large compared with bare needle. As expected, an increase in the number of fabric layers result in higher needle temperature.

• Steel and Composite Structures
• /
• v.9 no.2
• /
• pp.89-101
• /
• 2009

This paper presents a simplified model to study post-buckling behaviours of the axially restrained steel column at elevated temperatures in fire. The contribution of axial deformation to the curvature of column section is included in theoretical equations. The possible unloading at the convex side of the column when buckling occurs is considered in the stress-strain relationship of steel at elevated temperatures. Parameters that affect structural behaviours of the axial restrained column in fire are studied. The axial restraint cause an increase in the axial force before the column buckles; the buckling temperature of restrained columns will be lower than non-restrained steel columns. However, the axial force of a restrained column decreases after the column buckles with the elevation of temperatures, so make use of the post-buckling behaviour can increase the critical temperature of restrained columns. Columns with temperature gradient across the section will produce lower axial force at elevated temperatures.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2003.12a
• /
• pp.122-125
• /
• 2003

We investigated the effect of the abrasive and additive concentrations in Nano ceria slurry on the pad surface temperature under varying pressure through chemical mechanical polishing (CMP) test using blanket wafers. The pad surface temperature after CMP increased with the abrasive concentration and decreased with increase of the additive concentration in slurries for the constant down pressure. A possible mechanism is that the additive adsorbed on the film surface during polishing decreases the friction coefficient, hence the pad surface temperature gets lower with increase of the additive concentration. This difference of temperature was more remarkable for the higher concentration of abrasives. In addition, in-situ measurement of spindle motor was carried out during oxide and nitride polishing. The averaged motor current for oxide film was higher than that for nitride film, which means the higher friction coefficient.