• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2007년도 춘계학술논문 발표대회
• /
• pp.33-36
• /
• 2007

In order to select the optimum mix for the required fluidity and strength of mass concrete which is applied to transfer girder and to choose the optimum curing method depending on circumstances through hydration heat analysis of mass concrete, this study examined slump flow, air content and elapsed variation (0, 30, 60, 90) in unhardened concrete properties and reviewed compressive strength characteristics in hardening properties. And hydration heat analysis results through simulation are as follows; 1) Fluidity changes of unhardened concrete showed no significant difference, and those of elapsed variation also showed no difference but a bit of tendency to increase in comparison with the initial properties. 2) The higher the water-binder ratio was, the lower the compressive strength properties were, and the higher the fly ash replacement rate was, the lower the compressive strength development was. 3) In case of $Fc=40N/mm^2$, the optimum mix was fly ash replacement rate of 15% from water-binder ratio of 33.0%. 4) Hydration heat analysis results showed that in case of bundle cast, concrete temperature profile characteristics around transfer girder was unfavorable, and in case of separate cast, constant curing for at least seven days guaranteed thermal cracking index of 1.2.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계 학술발표회 논문집(II)
• /
• pp.413-416
• /
• 2006

In process of the mass concrete structure, the heat of hydration may cause serious thermal cracking. In order to eliminate hydration heat of mass concrete, this paper reports results of hydration heat control of mass concrete using the Oscillating Capillary tube Heat Pipe(OCHP). There were the several RC box molds which shows a difference as compared with each other. One was not equipped with OCHP. The others were equipped with OCHP. All of them were cooled with natural air convection. The OCHP was composed of copper pipe with 11 turns(outer diameter : 4mm, inner diameter : 2.8mm) and heat type was non-looped type. The working fluid was R-22 and its charging ratio was 40% by volume. The core of the concrete temperature was approximately $55^{\circ}C$ in the winter without OCHP. But the concrete temperature with OCHP was reduced its difference in temperature with the outdoor temperature to $12^{\circ}C$. Finally we saw the index figure of the thermal crack of the structures were varied from 0.75 to 1.47.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계 학술발표회 논문집(II)
• /
• pp.437-440
• /
• 2006

In process of the mass concrete structure, the heat of hydration may cause serious thermal cracking. In order to eliminate hydration heat of mass concrete, this paper results of hydration heat control of mass concrete using the Oscillating Capillary tube Heat Pipe(OCHP). There were the several molds which shows a difference as compared with each other. One was not equipped with OCHP. Other were laid with OCHP, and the other were laid in 100cm, and exposed out 50cm. All of them were cooled with natural air convection. The OCHP was composed of copper pipe(outer diameter : 4mm, inner diameter : 2.8mm) and heat type was non-looped type. The working fluid was R-22 and its charging ratio was 40% by volume. The core of the concrete temperature was approximately $53^{\circ}C$ without OCHP. But the concrete temperature with OCHP was reduced its difference in temperature with the outdoor temperature to $12{\sim}15^{\circ}C$. Finally we saw the index figure of the thermal crack of the structures were varied from 0.6 to 1.6.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2007년도 춘계학술논문 발표대회
• /
• pp.1-4
• /
• 2007

This study investigated the applicability of insulation curing method with double layer bubble sheets to the man concrete subjected to cold weather. Temperature history of the mass concrete indicated that the highest temperature of center section was exhibited at $34^{\circ}C$ while the that of surface section was $25^{\circ}C$. Difference between center and surface was shown to be less $10^{\circ}C$ when the temperature of center section was peak section, and thereby associated temperature cracking index was calculated 1.5, and occurrence probability of temperature cracking was 5%, so there was no temperature cracking caused by internal restraint. No temperature crack was observed by naked eye. It was clear that early frost demage and temperature cracking could be restrained due to reducing temperature difference between inner part and outside in the case double bubble sheets applied to insulation curing method in cold weather. The maturity of mass concrete is higher than outside about $72\sim89^{\circ}$ DD, so it was demonstrated to prevent early frost demage and ensure strength excellently. Insulation curing method with double bubble sheets was more economic than heating curing method.

• 한국구조물진단유지관리공학회 논문집
• /
• 제11권1호
• /
• pp.57-67
• /
• 2007

콘크리트 구조물의 사용수명은 콘크리트의 초기에 발생하는 균열에 큰 영향을 받는다. 특히 매스콘크리트 구조물에서는 수화열이 초기 온도균열의 주요한 원인이 된다. 이러한 온도균열은 콘크리트 표준시방서에 제시된 온도균열지수를 통해 분석할 수 있다. 따라서 본 논문은 내부구속이 지배적인 매스콘크리트에서 여러변수(시멘트종류, 타설높이, 양생조건, 타설온도, 단위시멘트량)에 따른 온도균열지수를 해석적으로 분석하였고, 분석결과는 변수의 변화에 따른 온도균열지수의 증감률로 나타내었다. 이러한 결과는 시공이나 설계시 온도균열을 파악하는 데 도움을 주어 경제적이고 안정적인 매스콘크리트 구조물의 설계에 유용하게 활용될 것으로 판단된다.

• 설비공학논문집
• /
• 제19권2호
• /
• pp.169-174
• /
• 2007

In process of reinforced concrete (RC) box structure, the heat of hydration may cause serious thermal cracking. This paper reports results of hydration heat control in mass concrete using the oscillating heat pipe. There were three RC box molds ($1.2m{\times}1.8m{\times}2.4m$) which were different from each other. One was not equipped with pulsating heat pipe. The others were equipped with pulsating heat pipe. All of them were cooled with natural air convection. The pulsating heat pipe was composed of 10 turns of serpentine type copper pipe whose outer and inner diameters were 4 and 2.8 mm respectively. The working fluid was R-22 and charging ratio was 40% by volume. The temperature of the concrete core was approximately $55^{\circ}C$ in the winter without pulsating heat pipe. For a concrete with pulsating heat pipe, however, the temperature difference with the outdoor one reduced up to $12^{\circ}C$. The index figure of crack was varied from 0.75 to 1.38.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2012년도 추계 학술논문 발표대회
• /
• pp.165-166
• /
• 2012

A thermal stresses by heat of hydration was analyzed according to a change of a pour height in reactor containment building. In case of more than 3.6m pouring height a crack index by heat of hydration analysis resulted in less than 1 because there is not a construction joint of vertical direction and for a self-restraint effect of circumferential section shape. Therefore detailed consideration on a mixture proportion of binder type, quantity in concrete and selection of a form in seasonal air temperature is needed for a control of tensile stress by heat of hydration.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2012년도 추계 학술논문 발표대회
• /
• pp.55-57
• /
• 2012

In this study, the field applicability on reducing the heat of hydration of mass concrete by using the hydration heat difference method is analyzed with the following summary. As a result of applying the hydration heat difference method by using low heating combination, the temperature difference between the central part and the surface part of mass material was reduced, and as a result of visual observation, there was no showing of cracks by the hydration heat on the upper surface part. Therefore, the cracking index of the field to apply this method was shown to be approximately 1.57 with very little crack occurrence probability of less than 3%.

• 한국광학회지
• /
• 제11권4호
• /
• pp.255-260
• /
• 2000

유기 금속화합물을 출발물질로 이용하는 졸-겔 방법으로 균열이 없는 유기-무기 복합 실리카 박막을 제작하였으며, 코팅방법, 조성비, prebake, postbake 온도 등의 제작조건에 따른 박막의 두께 및 굴절률의 변화를 체계적으로 조사하여 재현성 있는 제작조건을 확립하였다. 특히 광개시제를 첨가하였을 때 자외선 노광량에 따른 광학적 성질변화를 세 가지 광개시제에 대하여 측정, 비교하였다. 또한 졸-겔 박막으로 다중모드 간섭을 이용한 광 파워 분배기를 제작하여 광소자로의 응용 가능성을 살펴보았다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제21권2호
• /
• pp.103-113
• /
• 2017

고강도 콘크리트를 사용한 기초 부재의 수화열 제어를 위하여 지연형과 표준형 콘크리트 배합설계를 제안하고, 합리적인 타설 높이 구현이 가능하도록 유한요소해석을 실시하였다. 또한, 실물 실험을 통하여 해석결과와 비교하여 온도응력 저감 효과를 평가하였다. $6.5m{\times}6.5m{\times}3.5m$ 크기의 대형 부재에 지연형 및 표준형 콘크리트를 수평분할 타설한 결과, 최고온도 $77^{\circ}C$에서 중심부와 표면부의 온도차를 $25^{\circ}C$ 이내로 관리가 가능한 것으로 나타났다. 또한, 유한요소해석에 의한 온도균열지수가 1.49로 나타나 온도균열에 발생하지 않는 것으로 예측되었다. 지연형 및 표준형 콘크리트의 수평분할 타설이 고강도 매스콘크리트의 수화열에 의한 온도 응력 해소에 효과가 있는 것으로 나타났다.