• Journal of Radiation Protection and Research
• /
• 제22권3호
• /
• pp.135-141
• /
• 1997

열처리 특성의 연구는 열형광선량계를 재 사용하는데 있어서 중요하다. 최근 개발된 디스크 형태 (직경 4.5 mm, 두께 약 $90mg/cm^2$)의 LiF:Mg,Cu,Na,Si Teflon TLD의 열처리 조건을 구하기 위하여 조사전열처리, 판독과정 및 판독 후 열처리의 순서로 연구하였다. Teflon TLD의 감마선 조사는 $^{60}Co$ 0.1 Gy로 하였다. LiF:Mg,Cu,Na,Si Teflon TLD의 열처리 특성의 연구는 전기로와 판독장치를 이용하여 열처리 온도와 열처리 시간을 변화시키면서, 측정반복횟수에 따른 열형광강도 변화를 관찰하는 방법으로 수행하였다. LiF:Mg,Cu,Na,Si Teflon TLD의 열처리 조건은 조사전 열처리를 $80^{\circ}C$에서 1 시간 한 후 $280^{\circ}C$까지 판독하고 판독 후 열처리를 $270^{\circ}C$에서 20 초간 하는 것으로 결정되었고, 이 조건에서 10 회 반복측정시 원래의 열형광강도는 5%의 감소를 보였다.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제26권2호
• /
• pp.146-153
• /
• 2000

The purpose of present study is comparing the effect of Teflon Membrane and Nylon Membrane on bone regeneration in rabbit tibia. The 6 defects of $8{\times}8{\times}5mm$ size were drilled with dental handpiece in rabbit tibia, which on left side as an order of Control group(no coverage), Group 1(Nylon $5{\mu}m$ size), Group 3(Nylon $10{\mu}m$ size), and on right side Control group, Group 2($5{\mu}m$ Teflon), Group 4($10{\mu}m$ Teflon). Animals were killed at 7, 10, 14, 42 days to make specimens and observed the difference of healing potentials with light microscopy. The results were as follows ; 1. New bone formation has taken place at 14 days in Guided Bone Regeneration (GBR) group comparing to the Control group of massive inflammatory status. 2. Larger pore membrane allows more favorable healing potentials. Bone formation started earlier in larger membrane pore groups than smaller groups, until 14 days. 3. Bone forming potentials of Teflon membrane group was higher than Nylon membrane groups, Control group has the lowest bone forming potentials. 4. New bone formation was almost ended in 42 days, and there was no difference of bone formation between Nylon and Teflon membrane group of different size. There was no difference of bone formation at final stage(42 days) between Nylon membrane and Teflon membrane of same pore size. So nylon membrane may be clinically usable in guided bone regeneration case with further studies.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제25회 추계학술대회논문집
• /
• pp.495-499
• /
• 2005

인하 로케트 연구회에서는 기존의 복합추진제 모터의 노즐 재료를 기존의 세라믹에서 Teflon으로 대체하여 추력 성능을 개선하였다. Teflon으로 제작된 노즐은 지상시험과 추력 측정을 통해 결과를 확인하였다. Teflon을 이용한 노즐은 기존의 세라믹 노즐과 비교해서 신뢰성을 높이면서 총충격량을 18.3%만큼 증가시킬 수 있었다. 새로운 제작 공정은 노즐 생산 시간도 줄였다.

• 한국의학물리학회지:의학물리
• /
• 제14권2호
• /
• pp.74-80
• /
• 2003

본 연구의 목적은 핵의학 분야에서 생체 내 흡수선량의 직접 측정에 사용될 수 있는, 테프론을 씌운 TLD의 수행성을 알아보고, 흡수선량 측정 시 테프론의 영향에 대하여 분석하고자 한다. 테프론 캡슐에 든 LiF TLD-100의 반응감도를 고체 팬텀 내에서의 깊이를 달리 하며 측정하였다 성인 인체모형 팬텀을 이용하여 테프론을 씌운 TLD로써 생체 내 흡수선량을 측정하였다. 테프론을 씌우지 않은 보통의 TLD를 이용하여 구한 PDD, TMR, 그리고 생체흡수선량과 테프론을 씌운 TLD로 구한 값을 비교하였다. 보통의 TLD를 이용하여 구한 반응값과 테프론을 씌운 TLD로 구한 값의 차이는 build-up이상의 깊이에서는 같은 조건하에서 3％ 이내였다. 그러나 팬텀 표면 부근에서는 테프론 켑슐의 두께에 기인한 build-up 효과로 인해 큰 차이를 보였다. 본 연구에서 테프론 켑슐로 인하여 수 메가볼트의 방사선에 대한 TLD의 흡수선량 측정에 미치는 변화는 미미한 것으로 나타났다. 따라서 치료 환경 하에서 테프론을 씌운 TLD가 생체 내 선량측정에 매우 적합한 것으로 사료된다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.269-271
• /
• 2004

In this report, high-performance organic light-emitting diodes (OLEDs) with polytetrafluoroethylene (Teflon) buffer layer are demonstrated. Compared with conventional buffer layer, copper phthalocaynine (CuPc), Teflon film shows lower absorption in the wavelength from 200nm to 800nm The OLEDs with Teflon and CuPc buffer layer were fabricated under same conditions, and the device performances were compared. The results indicate that when the thickness of Teflon is 1.5nm, the performance of OLEDs is greatly enhanced with an efficiency of 9.0cd/A at the current density of 100mA/$cm^2$, while the device with an optimized 30-nm-thick CuPc buffer layer only shows an efficiency of6.4cd/A at the same current density.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 1999년도 제1회 학술대회논문집(KIASC 1st conference 99)
• /
• pp.173-176
• /
• 1999

Vacuum insulated pipes (VIP) are one of the important equipments for cryogenic fluids' transfer. Flange type of VIP, which can easily be installed at the site, uses a set of male and female bayonet with very small gap between them. In order to prevent leakage of liquid from inner pipe to bayonet. Teflon or Kel-F is located outside both the inner pipe of male and the guide of female. Even though liquid may leak at room temperature, it cannot leak at cryogenic temperature since Teflon shrinks much more than pipes and adheres closely to the inner pipe and guide. Teflon seal method has the advantage of easy fabrication, low cost and effective sealing compared to the conventional method.

• 한국기계가공학회지
• /
• 제6권4호
• /
• pp.81-85
• /
• 2007

A safety valve is used for protecting the pressure vessel and facilities by discharging the operating fluid into the valve from the accident when the pressure is over the designated value. The fluid is sulfurous acid and nitric acid. etc. in the semi-conductor assembly line. Thus the valve elements material must be acid resistance. Teflon, which is used generally as inner parts of a valve, tends to easily sticks to sliding surface by thermal expansion under high temperature. Some studies are performed to change teflon to another material and shape to have a better fluidity under the condition. The analysis of the thermal expansion is conducted by commercial FEM software to improve the problems. Boundary conditions were temperature and load in this study. From the analysis, the thermal expansion of stainless steel is verified to be lower than that of teflon under high temperature. Thus coupled teflon/stainless steel-made valve is applied to assembly line without danger due to thermal expansion.

• 대한화학회지
• /
• 제20권2호
• /
• pp.141-145
• /
• 1976

Scrap teflon으로부터 tetrafluoroethylene을 회수하기 위하여 Teflon을 온도와 압력등을 변화시키면서 열분해를 시도하였다. teflon은 내열성이 강하나 360$^{\circ}C$에서 장시간 유지하면 상압에서도 약간의 열분해가 일어난다. 얻어진 결과에 의하면 일반적으로 감압하에서 온도를 증가시키면 tetrafluoroethylene의 수득률이 상승하는 것을 알 수 있었다. 동분말을 사용하여 teflon의 분해를 시도하였으나, 현저한 변화를 볼 수 없었다.

• 한국안전학회지
• /
• 제18권3호
• /
• pp.60-63
• /
• 2003

For the increase the charge stability of teflon electrets for used at uncomfortable industrial circumstances with high temperature or humidity, We made an investigation into double layer effect of teflon electrets. Teflon AF film was spincoated on FEP film and then the charge storage property of AF/FEP dual film was investigated to be compared with FEP film. It was found that the AF/FEP dual film has higher surface potential than FEP film on the repeated charging and annealing process. It seems that AF/FEP dual film has higher thermal stability than FEP film through TSC measurement. If the investigations of the double layer effect of Teflon film carried out more closely with it's molecular structures and surface conditions, it may be effectively improved the stability of charge storage.

• Structural Engineering and Mechanics
• /
• 제48권6호
• /
• pp.809-822
• /
• 2013

Base isolation is widely used in seismic resisting buildings due to its low construction cost, high reliability, mature theory and convenient usage. However, it is difficult to design the isolation layer in high-rise buildings using the available bearings because high-rise buildings are characterized with long period, low horizontal stiffness, and complex re-distribution of the internal forces under earthquake loads etc. In this paper, a simple and innovative isolation bearing, named Teflon-based lead rubber isolation bearing, is developed to address the mentioned problems. The Teflon-based lead rubber isolation bearing consists of friction material and lead rubber isolation bearing. Hence, it integrates advantages of friction bearings and lead rubber isolation bearings so that improves the stability of base isolation system. An experimental study was conducted to validate the effectiveness of this new bearing. The effects of vertical loading, displacement amplitude and loading frequency on the force-displacement relationship and energy dissipation capacity of the Teflon-based lead rubber isolation bearing were studied. An analytical model was also proposed to predict the force-displacement relationship of the new bearing. Comparison of analytical and experimental results showed that the analytical model can accurately predict the force-displacement relationship and elastic shear deflection of the Teflon-based lead rubber isolation bearings.