• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.2
• /
• pp.137-144
• /
• 2008

In this paper, a novel voltage-controlled oscillator(VCO) using the output matching network based on the harmonic control circuit is presented for improving the phase noise property. The phase noise suppression is achieved through the harmonic control circuit having the short impedances for both second-harmonic and third-harmonic components, which has been connected at the output matching network. Also, we have used the microstrip square open loop multiple split-ring resonator(OLMSRR) having the high-Q property to further reduce the phase noise of VCO. Because the output matching network based on the harmonic control circuit has been used for reducing the phase noise property instead of the High-Q resonator, we can obtain the broad tuning range by the low-Q resonator. The phase noise of the proposed VCO using the output matching network based on the harmonic control circuit and the microstrip square OLMSRR has been $-127.5{\sim}126.33$ dBc/Hz @ 100 kHz in the tuning range, $5.744{\sim}5.839$ GHz. Compared with the reference VCO using the output matching network without the harmonic control circuit and the microstrip line resonator, the phase noise property of the proposed VCO has been improved in 26.66 dB.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.2
• /
• pp.67-74
• /
• 2008

This paper proposes two peak-windowing algorithms for peak-to-average power reduction(PAPR) of orthogonal frequency division multiple access(OFDMA) downlink systems. The Proposed algorithms mitigate the effect of excessive suppression due to successive peaks or relatively high peaks of the signal. First, multi-stage peak windowing algorithm is proposed, which exploits multiple threshold of target PAPR in order to step down the peaks gradually. Secondary, variable-length peak windowing algorithm is proposed, which adapts the window length with respect to the existence of successive peaks within a half of window length. Therefore, the proposed method reduces the distortion of signal amplitude caused by window overlapping. The proposed algorithms outperform the conventional peak windowing with the aid of window-length adaptation or sequential peak power reduction. Simulation results show the efficiency of the proposed algorithms over OFDMA downlink systems, especially WiBro systems.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.4
• /
• pp.31-37
• /
• 2008

Conventional cooperative communications can attain gain of spatial diversity and path loss reduction because destination node independently received same signal from source node and relay node located between source node and destination node. However, these techniques bring about decreased spectral efficiency with relay node and increased complexity of receiver by using maximal ratio combining (MRC). This paper has proposed cooperative ARQ protocol that can improve the above problems and can get the better performance. This method can increase the spectral efficiency than conventional cooperative communication because if the received signal from source node is satisfied by the destination preferentially, the destination transmits ACK message to both relay node and source node and then recovers the received signal. In addition, if ARQ message indicates NACK relay node operates selective retransmission and we can increase reliability of system compared with that of general ARQ protocol in which source node retransmits data. In the proposed protocol, the selective retransmission and ARQ message are to be determined by comparing log-likelihood ratio (LLR) computation of received signal from source node with predetermined threshold values. Therefore, this protocol don't waste redundant bandwidth with CRC code and can reduce complexity of receiver without MRC. We verified spectral efficiency and BER performance for the proposed protocol through Monte-Carlo simulation over Rayleigh fading plus AWGN.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.5 no.4
• /
• pp.83-93
• /
• 1994

1886년 고트리브 다이믈러와 칼 벤즈가 가솔린 자동차를 개발한 이후 100여년이 지난 지금 자동차는 비약적으로 진보, 발전하여 현대 산업사회와 개인의 생활에 있어 산업운송수단과 이동수단으 로서 필요불가결하게 되어 밀접한 관계를 갖고 있다. 우리나라 자동차 공업의 역사는 자동차가 사회적, 경제적 효용에 따라 그 생산과 보유대수가 날이 갈수록 증가 일로에 있으며, 자동차의 생산대수는 전세 계에서 년간 약 50,606천대('94년)로서 중요한 국가 기간 산업으로 자리하고 있다. 한편 전기, 전자공업의 발전에 따른 자동차의 Car Electronics가 많이 채용되게 됨에 따라 현재의 자 동차에는 대부분이 전자제어 System으로 구성되어 있다. 최근에는 Micro Processor를 이용한 전자부품이 많이 사용되어 전자파에 대한 문제가 다양하게 발생 하고 있다. 예를 들면 미국 캘리포니아주에서 전자점화제어장치와 연료분사 장치를 설치한 구미의 자동 차가 주행중 28MHz, 28W의 아마추어 무선을 탑제한 자동차가 통과할 때 엔진이 고르지 못한 보고가 있 었고, 화학섬유로된 옷을 착용한 전자부품이 다른 부품에 영향을 주는 사례가 맣아지고 있다. 따라서 자동차에는 여러가지의 전장품, 전자기기를 탑재하기 때문에 자동차 자체에서 발생하는 것과 외부로 부터 받는 전자장해 EMI(Electromagnetic Interference), EMS(Electromagnetic Susceptibility) 가 문제로 되어 자동차 및 부품 maker에 의한 EMC(Electromagnetic Compatibility) 평가의 중요성이 고조되고 있다. 차제무전기, 차제무전기, Car-Radio는잡음방해를 많이 받기도 하지만, 잡음원이 되기 도 한다. 또한 Engine 제어, 차속제어, Brake 제어등에 이용되는 전자제품은 방해에 의한 오동작 또는 파괴가 발생하여 주행기능, 안전성에 문제가 야기되지 않도록 해야 한다. 이러한 전자기 환경은 모두 RF(Radio Frequence)와 자동차에서의 전자파 장해 문제의 원이 될 수 있다. 자동차 및 그 부품의 전자기 방해에 관한 규격화는 1987년부터 괄목할 만하게 진행되어 이에 따른 규제 움직임이 IEC(International Electrotechnical Commission: 국제전기기술위원회) 산하의 하부기 구인 CISPR(International Special Committeeon Radio Interference: 국제 무선 장해 특별위원회)가 전자기 방해파에 대한 측정법 통일안을 제안 하였고, ISO(International Standardization Organiza- tion: 국제표준화 기구) 가운데 TC 22/SC3가 자동차의 전장품에 대한 장해를 논의히고 있다. 특히, 자동차의 EMC에 관한 국가 규격은 국제 규격에서 저술한 바와 같이 특별히 규정된 것이 없고 VDE(Verband Deutscher Elektrotechniker: 서독전기기술 협회)와 SAE(Society of Automotive Engi- neers: 자동차 기술자 협회)에서 비교적 활발하고 Jaso(Japanese Automobile Standards Organization: 일본 자동차 표준협회)에서 많이 진행중에 있다. 본 고에서는 자동차의 전자제어에 따른 잡음 발생 요인과 전자파 간섭 관련 자동차 규격과 시험평가 방법에 대해 간단히 소개 하였다.

• Journal of the Korean Dietetic Association
• /
• v.11 no.3
• /
• pp.365-374
• /
• 2005

This study was conducted to compare the validity of obese index among body mass index(BMI), waist to hip ratio(WHR), and waist circumference(WC) and to determine which is the best in relation to cardiovascular risk factors of middle aged Korean(40-64yr).Data from the 1998 Korean Health and Nutrition Survey were used(N=3380). Anthropometric indices and cardiovascular risk factors were measured. Chi-square test, analysis of variance following duncan's multiple range test, partial correlation analysis, and Receiver Operator characteristic(ROC) curves were used in the analysis. There was a significant increasing trend in WHR, systolic blood pressure(SBP), high density lipoprotein cholesterol(HDL), and fasting blood sugar(FBS) with age categories of male and in BMI, WC, WHR, diastolic blood pressure(DBP), SBP, total cholesterol(TC), low density lipoprotein cholesterol(LDL), triglycerol(TG), and FBS with those of female. Specially female had the characteristics of upper body fat and systolic blood pressure risk(p<0.05). Proportions of subjects with lifestyle factors related to cardiovascular risk in overweight or upper body fat group were higher than that of normal group. Higher proportions of subjects were practiced exercise in upper body fat group of male than in other groups. Among 7 cardiovascular risk factors in partial correlation analysis, BMI had the highest correlation coefficient in 6 risk factors in male, whereas WC in 4 risk factors in female. Mean of each obese index according to cardiovascular risk groups except smoker was higher than that of normal(p<0.05). These trends were shown in upper body fat group and female. In ROC analysis of 12 risk factors and health conditions, the largest area under curve among obese indices for risk factors were BMI in male and WHR in female. The optimal cutoff values of each index(BMI: WHR: WC) for one or more cardiovascular risk factors were 23.13: 0.89: 85.35 in male and 23.57: 0.84: 78.35 in female. The results showed that cardiovascular risk factors were prevalent in middle aged Koreans within normal limits of obese indices like another Asians. For the identification of cardiovascular risk factors of middle aged Koreans, BMI for men and WHR for women are appropriate indices. But it is recommended that BMI, WHR, and WC, all three indices should be considered, when using these indices.

• Journal of Sasang Constitutional Medicine
• /
• v.11 no.2
• /
• pp.209-226
• /
• 1999

In this study, we compared the effect of the Therapeutic Diet and Constitutional Diet on the subjects whose total number is 65 and has hyperlipidemia by checking the serum lipids 3weeks later, 6weeks later. In the Taeumin, there is a little difference in the two Dietary Therapies. Therapeutic Diet shows significant decrease in the total-cholesterol(6weeks later), triglyceride(6weeks later). (P<0.05) In that point Therapeutic Diet shows better effect than Constitutional Diet. Constitutional Diet shows better effect in the phospholipid by significant decrease in the phospholipid(6weeks later).(P<0.01) In the Soyangin group, Therapeutic Diet shows no difference, but Constitutional Diet shows significant decrease in the total lipid(3weeks, 6weeks later), phospholipid(3weeks later).(P<0.05).

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.7 s.349
• /
• pp.143-149
• /
• 2006

Turbo code, a kind of error correction coding technique, has been used in the field of digital mobile communication system. As the number of iterations increases, it can achieves remarkable BER performance over AWGN channel environment. However, if the number of iterations is increased in the several channel environments, any further iteration results in very little improvement, and requires much delay and computation in proportion to the number of iterations. To solve this problems, it is necessary to device an efficient criterion to stop the iteration process and prevent unnecessary delay and computation. In this paper, it proposes an efficient and simple criterion for stopping the iteration process in turbo decoding. By using sign changed ratio of extrinsic information values in turbo decoder, the proposed algorithm can largely reduce the average number of iterations without BER performance degradation. As a result of simulations, the average number of iterations is reduced by about $12.48%{\sim}22.22%$ compared to CE algorithm and about $20.43%{\sim}54.02%$ compared to SDR algorithm.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.7 s.349
• /
• pp.93-103
• /
• 2006

Network solutions for protecting against worm attacks that complement partial end system patch deployment is a pressing problem. In the content-based worm filtering, the challenges focus on the detection accuracy and its performance enhancement problem. We present a worm filter architecture using the bloom filter for deployment at high-speed transit points on the Internet, including firewalls and gateways. Content-based packet filtering at multi-gigabit line rates, in general, is a challenging problem due to the signature explosion problem that curtails performance. We show that for worm malware, in particular, buffer overflow worms which comprise a large segment of recent outbreaks, scalable -- accurate, cut-through, and extensible -- filtering performance is feasible. We demonstrate the efficacy of the design by implementing it on an Intel IXP network processor platform with gigabit interfaces. We benchmark the worm filter network appliance on a suite of current/past worms, showing multi-gigabit line speed filtering prowess with minimal footprint on end-to-end network performance.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.7 s.349
• /
• pp.72-83
• /
• 2006

It is not a practical solution that the DDoS attacks or worm propagations are protected and responded within a domain itself because it clogs access of legitimate users to share communication lines beyond the boundary a domain. Especially, the DDoS attacks with spoofed source address or with bogus packets that the destination addresses are changed randomly but has the valid source address does not allow us to identify access of legitimate users. We propose a scheme of distributed network security management to protect access of legitimate users from the DDoS attacks exploiting randomly spoofed source IP addresses and sending the bogus packets. We assume that Internet is divided into multiple domains and there exists one or more domain security manager in each domain, which is responsible for identifying hosts within the domain. The domain security manager forwards information regarding identified suspicious attack flows to neighboring managers and then verifies the attack upon receiving return messages from the neighboring managers. Through the experiment on a test-bed, the proposed scheme was verified to be able to maintain high detection accuracy and to enhance the. normal packet survival rate.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.7 s.349
• /
• pp.60-71
• /
• 2006

Group key agreement protocols are designed to allow a group of parties communicating over a public network to securely and efficiently establish a common secret key, Over the years, a number of solutions to the group key agreement protocol have been proposed with varying degrees of complexity, and the research relating to group key agreement to securely communicate among a group of members in integrated wired and wireless networks has been recently proceeded. Both features of wired computing machines with the high-performance and those of wireless devices with the low-power are considered to design a group key agreement protocol suited for integrated wired and wireless networks. Especially, it is important to reduce computational costs of mobile devices which have the limited system resources. In this paper, we present an efficient group key agreement scheme which minimizes the computational costs of mobile devices and is well suited for this network environment and prove its security.