• Proceedings of the KIEE Conference
• /
• 1996.11a
• /
• pp.251-253
• /
• 1996

High temperature superconducting (HTS) target has been irradiated by excimer laser beam. The surface of HTS target has been changed and showed the formation of cones. The laser ablated HTS target surface has been systematically studied using a scanning electron microscope. A KrF excimer laser with a wavelength of 248 nm was used to ablate the HTS YBCO target. The size of laser beam focused on the target showed a rectangular shape of $9.7{\times}2\;mm^2$. The image of SEM shows the difference between the shapes of cones fanned at the boundary and at the center of the ablated area after 1,000 laser pulses.

• 제어로봇시스템학회:학술대회논문집
• /
• 1994.10a
• /
• pp.494-497
• /
• 1994

We propose a novel velocity detection method of moving object based on a speckle pattern on the target surface using a self-mixing laser diode (SMLD). By this measurement, it was confirmed that the speckle signal has its waveform independent of the target velocity, and has its averaged frequency directly proportional to the target velocity. So it will be possible to detect the velocity of the target transversely translating against the laser light beam using a compact measuring system.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2004.10a
• /
• pp.11-14
• /
• 2004

In this paper, we propose a method to target searching method that have unstable limit cycles in a chaos trajectory surface. We assume all targets in the chaos trajectory surface have a Van der Pol equation with an unstable limit cycle When a chaos UAV meet the target in the Arnold equation, Chua's equation trajectory, the target absorptive the UAV

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.345.2-345.2
• /
• 2016

Alumina (Al2O3) doped zinc oxide (ZnO) films (AZO) have been prepared from 2 wt.% Al2O3 doped ZnO target by DC magnetron sputtering at a 2 mTorr (0.27 Pa) chamber pressure in (15 sccm) argon ambient. We obtained films of various opto-electronic properties by variation of target angle from 32.5o to 72.5o. At lower target angle deposited films show higher values in optical gap, mobility of charge carrier, carrier concentration, crystallite grain size, transmission range of wavelength, which are favorable characteristics of AZO as a transparent conducting oxide (TCO). At higher target angle the sheet resistance, work function, surface roughness for the AZO films increases. Measured haze ratio of the films changed lower to higher and size of characteristic surface structure of as deposited film ranges from ~40 nm to ~300 nm. By a combination of low and high target angle we obtained a textured TCO film with high conductivity.

• Journal of the Society of Naval Architects of Korea
• /
• v.42 no.5 s.143
• /
• pp.528-533
• /
• 2005

A mono-static high frequency acoustic target strength analysis scheme was developed for underwater targets, based on the far-field Kirchhoff approximation. Au adaptive triangular beam method and a concept of virtual surface were adopted for considering the effect of hidden surfaces and multiple reflections of an underwater target, respectively. A test of a simple target showed that the suggested hidden surface removal scheme is valid. Then some numerical analyses, for several underwater targets, were carried out; (1) for several simple underwater targets, like sphere, square plate, cylinder, trihedral corner reflector, and (2) for a generic submarine model, The former was exactly coincident with the theoretical results including beam patterns versus azimuth angles, and the latter suggested that multiple reflections have to be considered to estimate more accurate target strength of underwater targets.

• Journal of the Korean institute of surface engineering
• /
• v.38 no.5
• /
• pp.179-182
• /
• 2005

Indium Tin Oxide (ITO) thin films were deposited from various target densities ($98.7\%\~99.6\%$) using RF magnetron sputtering. Effect of the sputtering target densities on the structural, electrical and optical properties of deposited ITO thin films was investigated. The preferable (400) crystalline orientation peak was observed on the films deposited from > $99.0\%$ target density. Higher target density produced films with higher roughness but lower resistivity. All of the deposited films showed optical transmittance more than $85\%$ in the visible wavelength region. It is necessary to use the highest target density for sputtering deposition of ITO thin films.

• Progress in Superconductivity and Cryogenics
• /
• v.14 no.1
• /
• pp.1-3
• /
• 2012

LMO($LaMnO_3$) buffer layer of superconducting coated conductor was deposited on IBAD-MgO template in the plasma atmosphere at $650^{\circ}C$ which is relatively low compared with conventional deposition temperature of more than $800^{\circ}C$. Deposition method of LMO was DC sputtering, and target and deposition chamber were connected to the cathode and anode respectively. When DC voltage was applied between target and chamber, plasma was formed on the surface of target. The tape substrate was located with the distance of 10 cm between target and tape substrate. When anode bias was connected to the tape substrate, electrons were attracted from plasma in target surface to the tape substrate, and only tape substrate was heated by electron bombardment without heating any other zone. The effect of electron bombardment on the surface of substrate was investigated by increasing bias voltage to the substrate. We found out that the sample of electron bombardment had the effect of surface heating and had good texturing at low controlling temperature.

• Journal of the Korean institute of surface engineering
• /
• v.23 no.1
• /
• pp.1-7
• /
• 1990

Ion implantation is a well established superior superior surface modification technique for the improvement of wear resistance, hardenece, hardness, corrosion resistance, biocompaibity, surface friction, as well as for the modification of surface electric conductance. Conventional ion implantaion is a line-of-sight process witch ues the ion beam accelerator techniques. Plasma sheath ion implantation (PSII), as a new technique, is described in this paper. In PSII high voltage pulse is applied to a target material placed directly in a plasma, forming a think ion-matrix sheath around the target. Ions accelerate through the sheath drop and bombard the traget from all sides simultaneosuslyregardless of the target shape. This paper describes the principle of PSII, which has non-line-of sight characteristics, as well as the experimental appratus.

• Journal of KIISE
• /
• v.44 no.4
• /
• pp.411-416
• /
• 2017

The spectral radiance received by an infrared (IR) sensor is mainly influenced by the surface temperature of the target itself. Therefore, the precise temperature prediction is important for generating an IR target image. In this paper, we implement the combined three-dimensional surface temperature prediction module against target attitudes, environments and properties of a material for generating a realistic IR signal. In order to verify the calculated surface temperature, we are using the well-known IR signature analysis software, OKTAL-SE and compare the result with that. In addition, IR signal modeling is performed using the result of the surface temperature through coupling with OKTAL-SE.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.4C
• /
• pp.476-483
• /
• 2009

Tracking and detecting targets by the microwave seeker is affected by the clutter reflecting from the earth's surface. In order to detect retreating targets in look-down scenario, which appear in the sidelobe clutter (SLC) region, in the microwave seeker of high pulse repetition frequency (HPRF) mode, it is necessary to understand statistical characteristics of the surface SLC. Statistical analysis of SLC has been conducted for several kinds of the surface using data obtained by the captive flight test of the microwave seeker in the HPRF mode. The probability density function (PDF) fitting is conducted for several kinds and conditions of the surface. PDFs and PDF parameters, which best describe statistical distribution of the SLC power, are estimated. By using the estimated PDFs and PDF parameters, analyses for setting the target-detection thresholds, which give a desired level of target-detection false alarm probability, are made. These analysis materials for statistical characteristics of SLC power and the target-detection threshold can be used in various fields, such as development of a target-detection method, the constant false alarm rate processing.