• Design & Manufacturing
• /
• v.16 no.2
• /
• pp.53-59
• /
• 2022

Unlike other press forming processes, ISF (Incremental sheet forming) doesn't require a punch and die set. However, during the ISF processes unwanted bending deformation occurred around the target geometry. This paper is aimed to analyze the effect of the die structure, which is supported by bolts, on the geometric accuracy of the ISF processes. In this research, the ISF processes with Al5052 sheet of 0.5 mm, the tool diameter of 6 mm and the stepdown of 0.4 mm was employed. L-shaped, step-shaped, relief-shaped geometry were employed in experiments. Sectional view and the plastic strain were compared. From this research we find out that the bolt supported ISF processes increases the geometric accuracy of products very effectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.345.2-345.2
• /
• 2016

Alumina (Al2O3) doped zinc oxide (ZnO) films (AZO) have been prepared from 2 wt.% Al2O3 doped ZnO target by DC magnetron sputtering at a 2 mTorr (0.27 Pa) chamber pressure in (15 sccm) argon ambient. We obtained films of various opto-electronic properties by variation of target angle from 32.5o to 72.5o. At lower target angle deposited films show higher values in optical gap, mobility of charge carrier, carrier concentration, crystallite grain size, transmission range of wavelength, which are favorable characteristics of AZO as a transparent conducting oxide (TCO). At higher target angle the sheet resistance, work function, surface roughness for the AZO films increases. Measured haze ratio of the films changed lower to higher and size of characteristic surface structure of as deposited film ranges from ~40 nm to ~300 nm. By a combination of low and high target angle we obtained a textured TCO film with high conductivity.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.611-614
• /
• 2005

In this paper, investigated is the relationship between the formation temperature and the thermal stability of Ni silicide formed with Ni-V (Nickel Vanadium) alloy target. The sheet resistance after the formation of Ni silicide with the Ni-V showed stable characteristic up to RTP temperature of $700\;^{\circ}C$ while degradation of sheet resistance started at that temperature in case of pure-Ni. Moreover, the Ni silicide with Ni-V indicated more thermally stable characteristic after the post-silicidation annealing. It is further found that the thermal robustness of Ni silicide with Ni-V was highly dependent on the formation temperature. With the increased silicidation temperature (around $700\;^{\circ}C$), the more thermally stable Ni silicide was formed than that of low temperature case using the Ni-V.

• Proceedings of the Korean Biophysical Society Conference
• /
• 2003.06a
• /
• pp.63-63
• /
• 2003

$\alpha$$_1$-Antityrpsin is a member of the serine protease inhibitor (SERPIN) family that shares a common tertiary structure. The reactive site loop (RSL) of serpins is exposed at one end of the molecule for protease binding. Upon cleavage by a target protease, the RSL is inserted into the major $\beta$-sheet A, which is a necessary process for formation of a tight inhibitory complex. Various biochemical and structural studies suggest that the rate of the RSL insertion upon binding a target protease is critical for inhibitory activity, and it is thought that helix F region (thFs3A and helix F) located in front of $\beta$-sheet A, should be lifted for the loop insertion during complex formation.

• Laser Solutions
• /
• v.3 no.3
• /
• pp.13-19
• /
• 2000

The stencil is a thin stainless sheet in which a pattern is formed, which is placed on a surface of plate to reproduce the pattern of electric circuit. Conventionally the stencil has been produced by etching process. This process has many anti-environmental factors. In this study, Nd : YAG laser cutting process has been applied for stencil manufacturing. The study is focused on estimating kerf width of laser cut stencil by E.B.P.(Error Back-Propagation). This algorithm is good for estimating target value from input value. In this paper, target value was kerf width, and input values were frequency, pulse width, cutting speed and laser power. E.B.P. after teaming input and target could estimate kerf width from some variables precisely.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1428-1429
• /
• 2009

Compared to the indium zinc oxide (IZO) film fabricated by micro-powder target, the IZO film with nano-powder target exhibited improved optoelectronic properties of wide bandgap, high transmittance, surface uniformity, and low sheet resistance due to the high film density.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.379-380
• /
• 2007

The characteristics of a co-sputtered indium zinc tin oxide (IZTO) films prepared by dual target dc magnetron sputtering from IZO and ITO targets at a room temperature are investigated. Film properties, such as sheet resistance, optical transmittance, surface work function and surface roughness were examined as a function of ITO dc power at constant IZO dc power of 100 W. It was shown that the increase of the ITO dc power during co-sputtering of ITO and IZO target resulted in an increase of sheet resistance of the IZTO films. This can be attributed to high resistivity of ITO film prepared at room temperature. Surface smoothness and roughness were investigated by Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM). The synchrotron x-ray scattering results obtained from IZTO film with different ITO contents showed that introduction of ITO atoms into amorphous IZO film resulted in a crystallization of IZTO film with (222) preferred orientation due to low alc transition temperature of ITO film. However, the transmittance of the IZTO films with thickness of 150 nm is between 80 and 85 % at wavelength of 550 nm regardless of ITO content. Possible mechanism to explain the ITO and IZO co-sputtering effect on properties of IZTO is suggested.

• Journal of Radiation Protection and Research
• /
• v.42 no.3
• /
• pp.141-145
• /
• 2017

Background: The concrete walls inside the vaults of cyclotron facilities are activated by neutrons emitted by the targets during radioisotope production. Reducing the amount of radioactive waste created in such facilities is very important in case they are decommissioned. Thus, we proposed a strategy of reducing the neutron activation of the concrete walls in cyclotrons during operation. Materials and Methods: A polyethylene plate and B-doped Al sheet (30 wt% of B and 2.5 mm in thickness) were placed in front of the wall in the cyclotron room of a radioisotope production facility for pharmaceutical use. The target was Xe gas, and a Cu block was utilized for proton dumping. The irradiation time, proton energy, and beam current were 8 hours, 30 MeV, and $125{\mu}A$, respectively. To determine a suitable thickness for the polyethylene plate set in front of the B-doped Al sheet, the neutron-reducing effects achieved by inserting such sheets at several depths within polyethylene plate stacks were evaluated. The neutron fluence was monitored using an activation detector and 20-g on de Au foil samples with and without 0.5-mm-thick Cd foil. Each Au foil sample was pasted onto the center of a polyethylene plate and B-doped Al sheet, and the absolute activity of one Au foil sample was measured as a standard using a Ge detector. The resulting relative activities were obtained by calculating the ratio of the photostimulated luminescence of each foil sample to that of the standard Au foil. Results and Discussion: When the combination of a 4-cm-thick polyethylene plate and B-doped Al sheet was employed, the thermal neutron rate was reduced by 78%. Conclusion: The combination of a 4-cm-thick polyethylene plate and B-doped Al sheet effectively reduced the neutron activation of the investigated concrete wall.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.23 no.6
• /
• pp.43-55
• /
• 2020

The study was performed in order to derive the management methods of revegetation space on embankment upper in the shoulder of expressway. The pilot study was conducted in 2013 on the test road section of the Jungbu Inland Expressway (Smart Highway) and continues to be monitored until 2020. In the test, three commonly used methods for weed control were applied. In the early two to three years, most of the methods were effective in controlling weeds. However, at the end of six years, weed suppression effects were different for each treatment. Vegetation coverage was 90% in the untreated control, 70-80% wood chip mulching method, 50-60% solidification method, and 20% sheet mulching method. The sheet method was found to be the most effective given the low vegetation coverage was effective in controlling weeds. The wood chip mulching method is promoting weed growth over time, and weeds are invading as the effect of soil hardening is reduced in the place where the soil hardener is treated. Among the methods applied in the test, mulching the sheet is the most effective, but it is important to use a durable sheet. In the future, it is necessary to find ways to control weeds on road shoulders, considering both economic and environmental aspects. For the proper management in the shoulder of expressway set target zone is needed. Clear standards for weed control on expressway should be established. And the technology to be applied must be durable for 3 years or more and must be able to suppress the amount of weeds to a level of 20% or less.

• Journal of the Korea Institute of Building Construction
• /
• v.7 no.1 s.23
• /
• pp.107-113
• /
• 2007

This study investigates the filed application in Daebul Free Trade Zone applying both a flowing method using drying shrinkage-reducing superplasticizer(SRS) and an insulating curing method using double layer bubble sheet. Test results showed that fresh concrete satisfied target slump and air content. A structure adding SRS significantly decreased the total bleeding capacity and accelerated the setting time. As for the crack occurrence, the structure applying the flowing method and double bubble sheets simultaneously exhibited the most favorable crack endurance, while conventional concrete showed more than 1mm size of crack in overall. In addition, a structure applying the flowing concrete method partially presented the micro crack. For the area proportion of crack occurrence, the structure using the double bubble sheets indicated 9.8%, while others applying flowing concrete method was 28%, compared with that of conventional one. For the compressive strength of specimens, standard curing specimens indicated $3{\sim}33%$ higher value than that of specimens cured besides the field construction. The specimens containing SRS improved the strength of $2{\sim}6MPa$, which is $10{\sim}22%$ higher than that of conventional concrete.