• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.3
• /
• pp.499-503
• /
• 2016

For safety and economy reasons, hazardous waste including radioactive waste is desired to be converted into stable waste forms with a maximum volume reduction. High temperature melting technology using a plasma torch system can effectively treat even the non-flammable waste as desired. By far, one of the most difficult process for melting the non-flammable waste is a tapping of melts because the melting point of a residual slag in the tapping hole is high and because the viscosity of the melt increases sharply when tapping out. In case of a stationary furnace with a slant tapping port on the side of furnace, a certain amount of melts is left in the tapping hole after tapping out. Because of this, at every end of a melting cycle, the tapping hole needs to be opened by tapping device. The developed tapping device of melts based on both a guide electrode and auxiliary electrode is adequate for the application to discharge of melts except that the consumption of the guide electrode is somewhat faster than expected. Melt is collected in the water cooled vessel.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.1
• /
• pp.80-86
• /
• 2011

This study compared and analyzed manual tapping and automatic tapping regarding tapping process characteristics of titanium hard-to-cut-material. Tapping process characteristics of titanium hard-to-cut-material are evaluated as the quality of a screw, wear of a tap, economic analysis, and cycle time etc. The type of screw threads after manual tapping is formed as an irregular type of screw threads, and perfect screw threads are created after automatic tapping. In addition, the chip type after manual tapping process is formed as the discontinuous chip due to work hardening, and the powder type of chip after automatic tapping process is created. In terms of cycle time, an automatic tapping process is shortened by 70% compared to manual tapping process. Insert tip wear of an automatic tapping shown in the process of 5-hole tapping is not found, but hand tap wear for finish cutting is most severe.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.11
• /
• pp.55-62
• /
• 2000

The poor machinability material such as austenite stainless steel(STS304) is emphasized on the wide use of HSSE for the tapping operation. The difficulty can be entirely to tapping torque due to chip formation through the hole of tap. The object of this study is to investigate tap geometry affecting the tapping torque from a practical point of view. The study shows that the optima tapping torque is affected by the tap geometry and cutting condition for STS304.

• Journal of the Korean Wood Science and Technology
• /
• v.49 no.2
• /
• pp.181-190
• /
• 2021

Screw-type fasteners are widely used to make connections between wood members or between wood and steel connectors because they can tolerate the applied loads by withdrawal or shearing. In this study, we evaluated the withdrawal resistances of the screw-type fasteners and analyzed the effects of the lead-hole size, relative grain direction (tangential, radial, and cross-sections) of the wood member, screw diameter, screw type, and species. Two wood species, including domestic larch and imported spruce, and three screw-type fasteners, including domestic lag screws (diameters of 9.46, 7.79, and 6.27 mm), domestic tapping screw (diameter, 6.3 mm), and imported Sherpa screw (diameter, 8.0 mm) were used. To assess the effect of lead-hole size, the lead holes with diameters corresponding to 68.7%, 70.8%, and 74.0% of the shank diameter of the lag screw were predrilled. The lead hole corresponding to 74% of the shank diameter was selected for this study because the smaller lead holes required higher rotational force for installation, which may cause damage in the screw neck, although there was no significant difference in the withdrawal resistance depending on the lead-hole sizes applied in this study. The lag screws installed on the tangential and radial surfaces showed similar withdrawal resistances to each other, which were greater than those installed on the cross-sectional surface. As the lag screw diameter increased from 6.27 mm to 9.46 mm, the withdrawal resistance also increased proportionally. The withdrawal resistance of the tapping screw having a diameter of 6.3 mm was almost 1.6 times higher than that of the lag screw having a similar diameter of 6.27 mm, while that of Sherpa screw having a diameter of 8.0 mm was around 1.4 times higher than that of the lag screw having a similar diameter of 7.79 mm.

• Journal of the Korean Society of Safety
• /
• v.25 no.2
• /
• pp.1-6
• /
• 2010

Flow characteristics of differential pressure flow meters which have a shape of triangular separate bar (TSB) was investigated according to the machining conditions in pressure tapping holes. Diameter of the pressure taping holes is either 1.0 mm or 1.5 mm. Also, number of the pressure tapping holes are drilled either 9 or 17. The mass flow rate of the TSB flow meters are calibrated with a laminar flow meter by connecting them in line. The mass flow rate in the TSB flow meters are plotted with a non-dimensional parameter H which includes the gas temperature, exhaust gas pressure and differential pressure at the flow meters. An empirical correlation between the mass flow rate at the TSB flow meter and the non-dimensional parameter H was obtained. The empirical correlation showed highly linear relationship between the mass flow rate and the non-dimensional parameter H. The hole size of the pressure tapping holes has a bigger effect on the flow rate than the number of the tapping holes.

• Journal of the Korean Wood Science and Technology
• /
• v.20 no.4
• /
• pp.15-20
• /
• 1992

This study was carried out to improve the method of tapping sap from Betula platyphylla Sukatschev, Betula costata Trautv., Betula schmidtii Regel, Betula davurica Pallas, Betula ermanii Cham, Acer mono Maxim and Acer pseudo-sieboldianum Kom and to use it to natural drinks. The mal or results are as follows: 1. It is no difference of the amount of sap by tapping methods and species of trees. The larger D.B.H. is, the more amount of sap can be gotten. So we thought that the best tapping method is hole-drilling to prevent trees from damage. 2. Sap contains sugars and mineral materials. Birches have glucose and fructose, much more mineral materials than maples. Sugar of maples is mainly sucrose. 3. We assume that mineral materials of birches are effective to urination, to make a stong dody and sucrose of maples is effective to recover from one's fatigue by controlling the blood sugar. 4. In vacuum packing after sterilizing the sap in low temperature, it could be stored more 1 year. So, it is possible that sap will be commercialized.

• Journal of Korean Neurosurgical Society
• /
• v.45 no.5
• /
• pp.318-321
• /
• 2009

Tension pneumocephalus may follow a cerebrospinal fluid(CSF) leak communicating with extensive extradural air. However, it rarely occurs after diagnostic lumbar puncture, and its treatment and pathophysiology are uncertain. Tension pneumocephalus can develop even after diagnostic lumbar puncture in a special condition. This extremely rare condition and underlying pathophysiology will be presented and discussed. The authors report the case of a 44-year-old man with a basal skull fracture accompanied by pneumothorax necessitating chest tube suction drainage, who underwent an uneventful lumbar tapping that was complicated by postprocedural tension pneumocephalus resulting in an altered mental status. The patient was managed by burr hole trephination and saline infusion following chest tube disengagement. He recovered well with no neurologic deficits after the operation, and a follow-up computed tomography (CT) scan demonstrated that the pneumocephalus had completely resolved. Tension pneumocephalus is a rare but serious complication of lumbar puncture in patients with basal skull fractures accompanied by pneumothorax, which requires continuous chest tube drainage. Thus, when there is a need for lumbar tapping in these patients, it should be performed after the negative pressure is disengaged.

• Journal of the Korean Wood Science and Technology
• /
• v.26 no.3
• /
• pp.93-99
• /
• 1998

Lately public interest in tree saps of maple and birch trees stimulated to increase demands for sap drink as a natural medical beverage. In order to understand factors affecting tree sap flows, birch species, particularly Betula platyphylla in Mt.Sobaek area, were monitored for daily sap flows according to factors, such as DBH, tapping hole sizes and direction of hole drilling on the trunks. The chemical constituents of saps were also analyzed. The sap flow initiated from the end of March and finished at the end of April. The flow maxima appeared from April 14th to April 26th. Total amounts of the sap flow obtained from birch tree were over 1,800 ml per day per one tree. Sap flows were increased with increasing DBH and tree age. Six milimeter drilled hole resulted in the highest sap flows. Sap flows increased with increases of diameter and height of the trees. Hole drilling to downward side(south-facing) of tree produced almost doubled sap flows than that of upward one(north-facing), while rightside drilling produced same amounts of saps to that of leftside one. Six mm drilling gave the best results not only in maximum flows but also effective hole occluding rates. The saps have in the range of 4.5 to 5.6 pH and l.0 - 2.0% of saccharinity. Sucrose, glucose, fructose and high mineral contents were found in the saps of birch tree. The tree saps could be utilized not only medicinal drink, but also one of the healthy beverages.

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.1680-1686
• /
• 2009

Flow characteristics of a differential pressure flow meters which have a shape of triangular separate bar (TSB) was investigated according to machining conditions in pressure tapping holes. Size of pressure tapping holes is machined with either 1.0 mm or 1.5 mm in diameter. Also, number of pressure tapping holes are drilled either 9 or 17. The mass flow rate of the TSB flow meters are calibrated with a laminar flow meter by connecting them in line. The mass flow rate in the TSB flow meters are plotted with a non-dimensional parameter H which includes the gas temperature, exhaust gas pressure and differential pressure at the flow meters, and atmospheric pressure. An empirical correlation between the mass flow rate at the TSB flow meter and the non-dimensional parameter H was obtained. The empirical correlation showed highly linear relationship between the mass flow rate and the non-dimensional parameter H. The hole size of the pressure tapping holes has a bigger effect on the flow rate than the number of the tapping holes.

• Journal of Korean Society of Forest Science
• /
• v.95 no.1
• /
• pp.1-4
• /
• 2006

Closing processes of taping holes and diameter growth of taped trees of Acer mono were investigated to understand the effects of sap taping and number of tapping holes on tree growth and closing speed of holes. Closing processes of tapping holes were faster at trees taped of ten holes than trees tapped of one, three, five holes during the study period, and tapped holes were completely filed up within 15 months. Diameter growth by number of tapped hole were 0.54 mm for control trees, 0.60 mm for trees taped of one hole, 0.64 mm for trees taped of three holes, 0.33 mm for tapped of five holes and 0.31 mm for trees taped of ten holes, respectively. Closing processes of tapping holes by fusion materials was fast in the order of DB ointment, stirofoam, control and bamboo vinegar. Especially, tapped holes in the case of DB ointment was completely healed within 4 months. Therefore, DB ointment should be used to minimize damage on tree growth and secure resources for sap collection of A. mono.