• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.04b
• /
• pp.60-63
• /
• 2000

The $0.94MgTiO_3-0.06SrTiO_3$ ceramics were prepared by the conventional mixed oxide method. The structural properties were investigated with sintering temperature and composition ratio by XRD, SEM and DT-TGA. According to the X-ray diffraction patterns of the $0.94MgTiO_3-0.06SrTiO_3$ ceramics, the cubic $SrTiO_3$ and hexagonal $MgTiO_3$ structures were coexisted. Increasing the sintering temperature from $1325^{\circ}C$ to $1400^{\circ}C$, average grain size was increased from $5.026{\mu}m$ to $8.377{\mu}m$. In the case of the $0.94MgTiO_3-0.06SrTiO_3$ ceramics sintered at $1325^{\circ}C$, dielectric constant, quality factor and temperature coefficient of resonant frequency were 21.66, 2,522(at 7.34GHz), $+71ppm/^{\circ}C$, respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.68-68
• /
• 2000

펄스레이저 증착법(이하 PLD)을 이용하여 마이크로파 유전체 소자 및 절연 산화막으로의 응용을 위한 MgTiO3 박막을 다양한 기판상에서 증착하였다. 사파이어 기판에 (a,c-plane Al2O3) 성장된 MgTiO3 박막은 에피텍셜 성장(epitaxial growth)이 되었으며, SiO2/Si 및 Pt/Ti/Si 기판위세 성장된 MgTiO3 박막의 경우 003방향으로 배향(oriented) 되었다. MgTiO3 박막은 450~75$0^{\circ}C$까지 기판온도를 변화시키면서 증착시켰으며, 증착시 산소분압은 50~200 mTorr로 변화시켰다. PLD 증착시 타켓에 조사된 레이저 에너지 밀도는 약 2J/cm2였으며, MgTiO3 박막 증착후 200Torr O2 분위기에서 상온까지 1$0^{\circ}C$/min 의 속도로 냉각시켰다. 사파이어 c-plane 상에서 일머나잇(ilminite) MgTiO3 구조가 55$0^{\circ}C$ 에피텍셜 성장하는 것을 관찰할 수 있었으며, 사파이어 a-plane 상에서는 MgTiO3 구조가 $650^{\circ}C$ 이상부터 110방향으로 배향되며 성장하였다. $600^{\circ}C$ 이상에서 c-축으로 배향된 구조를 갖고 있었다. 증착된 MgTiO3 박막의 조성분석(stoichio metric analysis)을 위해 RBS 분석을 수행하여, 증착에 이용된 타켓과 동일한 조성을 갖는 MgTiO3 박막이 성장된 것을 확인할 수 있었다. 사파이어 기판상에 증착된 MgTiO3 박막은 가시영역에서 투명하였으며, 약 270nm 파장을 갖는 영역에서 급격한 흡수단을 보였다. 이때의 MgTiO3 박막은 AFM 분석을 통해 약 0.87mn rms roughness 값을 갖는 매우 평탄한 표면구조를 갖고 있는 것을 확인하였다. MIM(Pt/MgTiO3/Pt) 구조의 캐패시터를 형성시켜 MgTiO3 박막의 유전특성(dielectric properties)을 관찰하였다. PLD로 성장된 MgTiO3 박막의 유전율(relative dielectric constant)은 약 22였으며, 1MHz에서 약 1.5%의 유전손실(dielectirc loss) 값을 보였다. 또한 이때 MgTiO3 박막은 낮은 유전분산값을 보였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.236-237
• /
• 2005

The structural properties of $(Bi,Ce)_4Ti_3O_{12}(BCT)$ thin films with post-annealing temperature were investigated. $(Bi,Ce)_4Ti_3O_{12}(BCT)$ thin films were deposited by RF sputtering method on Pt/Ti/$SiO_2$/Si substrates with optimum deposition condition. The $(Bi,Ce)_4Ti_3O_{12}(BCT)$ thin films was post-annealed at 600$^{\circ}C$, 650$^{\circ}C$, 700$^{\circ}C$, 750$^{\circ}C$, 800$^{\circ}C$ in furnace,respectively. Increasing the post-annealing temperature, the grain size, density and peak intensity of (117) and c-axis orientation were increased. The $(Bi,Ce)_4Ti_3O_{12}(BCT)$ thin films that annealed at 750$^{\circ}C$ exhibited well crystallized phase and had no vacancy and grain was uniform. but there are some secondary phases observed. At this time, the average thickness of $(Bi,Ce)_4Ti_3O_{12}(BCT)$ thin films was 2000 ${\AA}$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.208-211
• /
• 2000

We prepared Co-Cr-Ta and Co-Cr-Ta/Ti thin film for perpendicular magnetic recording media by facing targets sputtering system (FTS system). Ti underlayer effects on crystallographic and magnetic characteristics of Co-Cr-Ta perpendicular magnetic recording media have been investigated. Crystallgraphic and magnetic characteristic of prepared thin films were evaluated by x-ray diffractometry(XRD), vibrating sample magnetometer(VSM) and kerr hysteresis loop measurement. The coercivity and anisotropy field increase by introduced Ti underlayer when substrate temperature is higher than 150$^{\circ}C$. The c-axis dispersion angle and grain size of Co-Cr-Ta/Ti thin film is decrease than Co-Cr-Ta when substrate temperature is higher than 100$^{\circ}C$. Consequently, the use of a Ti underlayer highly orientated can be improved crystallographic and magnetic characteristics of Co-Cr -Ta perpendicular media layer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.71-74
• /
• 2000

Pt/Pb$TiO_3$/$SrTiO_3$/p-Si films were prepared by metallo-organic solution deposition(M0SD) method and investigated its structure and ferroelectric properties. Crystallinity of specimen as a funtions of post annealing temperature and the thickness of $SrTiO_3$(STO) buffer layer was studied using XRD and AFM. Based on C-V and P-E curve, $PbTiO_3$(PTO) capacitors showed good ferroelectric hysteresis arising from the polarization switching properties. When the thickness of ST0 buffer layer between PTO and Si substrate was 260 nrn and the post annealing temperature was $650^{\circ}C$, it was showed that production of the pyrochlore phase due to interdiffusion of Si into FTO was prevented. The dielectric constant of FTO thin films calculated from a maximum Cma in the accumulation region was 180 and the dielectric loss was 0.30 at 100 kHz frequency. The memory window in the C-V curve is 1.6V at a gate voltage of 5V.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2000.11a
• /
• pp.27-27
• /
• 2000

TDEAT precursor를 이용하여 DC-Pulse Plasma MOCVD 방법과 Thermal MOCVD 방법으로 각각 TiN 박막을 증착하였다. 본 논문에서는 DC-Pulse Plasma MOCVD 방 법으로 증착된 TiN 박막과 Therrnal MOCVD 방법으로 증착된 TiN 박막의 전기적 특성에 관하여 비교 분석하였다. 동일한 조건 하에서 각각의 방법으로 증착된 박막은 4-point probe를 이용하여 면저항을 측정하였고, XRD를 이용하여 박막의 성장방향을 관찰하였으며, FE-SEM을 이용하여 박막의 두께와 단면 사진, 표면형상을 관찰하였으며, AES depth profile을 통해 두께에 따른 Ti, N, 잔류 C와 0의 함량을 분석하였으며, XPS를 통해 C의 결합형태를 파악하고자 하였다. 분석결과 DC-Pulse Plasma MOCVD 방법으로 증착된 TiN 박막이 Thermal MOCVD 방법으로 증착된 TiN 박막에 비해 전기적 특성은 매우 우수하였으며, 치밀한 구조의 박막을 가지는 것으로 나타났다. 또한, 잔류 C, O의 함량이 낮은 것으로 나타났다.

• Journal of Welding and Joining
• /
• v.18 no.5
• /
• pp.105-111
• /
• 2000

The wear behavior of thermal sprayed AlSiMg-40TiC composite coatings were studied as a function of load and sliding velocity under unlubricated conditions. Experiments were performed using a block-on-ring(WC-6wt%/Co, Hv 1500) type. The tests were carried out a various load(30∼ 125.5N) and sliding velocity(0.5∼2.0m/s). Three wear rate regions were observed in the AlSiMg-40TiC composite coatings. The wear rate in region I at low load (less then 8N( were less than 1×{TEX}$10^{-5}${/TEX}㎣/m. Low wear rates in region I resulted from the load-bearing capacity of TiC particles. The transition from region I to II occurred when the applied load exceeded the fracture and pull-out strength of the particles. The TiC fractured particles trapped between the specimen and the counterface acted as third-body abrasive wear. The subsurface layer worn surface in region II was composed of the mechanically mixed layer (MML). The wear rate increase abruptly above a critical load (region III). The high wear rate in region III was induced by frictional temperature and involves massive surface damage.

• Transactions on Electrical and Electronic Materials
• /
• v.1 no.2
• /
• pp.28-31
• /
• 2000

BaTiO$_3$cerameic thin films doped with Mn were manufactured by rf/dc magnetron sputter technique. We have investigated crystal structure, surface morphology and PRCR(positive-temperature coefficient of resistance) characteristics of the specimen depending on second heat-treatment temperature. Second heat treatment of the specimen were performed in the temperature range of 400 to 1350$\^{C}$ X-ray diffraction patterns of BaTiO$_3$ thin films show that the specimen heat treated below 600$\^{C}$ is an amorphous phase and the one heat treated above 1100$\^{C}$ forms a poly-crystallization . In this specimen heat-treated at 1300$\^{C}$, a lattice constant ratio(c/a) was 1.188. Scanning electron microscope(SEM) image of BaTiO$_3$ thin films of the specimen heat treated in between 900 and 1100$\^{C}$ shows a grain growth. At 1100$\^{C}$, the specimen stops grain-growing and becomes a poly-crystallization . A resistivity-temperature characteristics of the specimen depends on the doping concentrations of Mn. A resistivity ratio between the value at room temperature and the one above Curie temperature was 10$^4$ for pure BaTiO$_3$ thin films and 10$\^$5/ fo BaTiO$_3$ : additive 0.127mol% MnO

• Journal of the Korean Ceramic Society
• /
• v.37 no.4
• /
• pp.308-313
• /
• 2000

Hydrous titanium oxide particles with anatase phase were prepared from 0.05 mol TiCl4 solution using NH4HCO3 as precipitant by the droopping precipitant method. The sequential change of pH is completed by a sudden and steep increase in a pH value of the range of 6~7 to which the concentration of adsorbed OH- and H+ ions on TiO2 surface is equal. Rutile phase started precipitating with anatase phase as an increase of reaction temperature above 6$0^{\circ}C$ in aqueous 0.05mol TiCl4 solution and its specific surface area was found to decrease from 452 $m^2$/g($25^{\circ}C$) to 164$m^2$/g(8$0^{\circ}C$). Specific surface area decreased rapidly when anatase powders precipitated at 4$0^{\circ}C$ were heat-treated at temperature higher 40$0^{\circ}C$. FT-IR result confirmed that it was due to the decrease of OH species within hydrous titanium oxides. The loss of ethanol after illumination of the powder heated at $600^{\circ}C$ and $700^{\circ}C$ for 4 h was 66 and 68.8%, respectively.

• Bulletin of the Korean Chemical Society
• /
• v.21 no.12
• /
• pp.1181-1186
• /
• 2000

The structural evolution during the thermal treatment of $70SiO_2-3OTiO_2(mole%)$ sol-gel derived powders and films was investigated by FT-IR, Raman and XPS, and XRD. From these results, the $TiO_2-rich$ regions involving $Ti^{4+}$ ions in octahedral coordination were confirmed to be amorphous at $600^{\circ}C$. However, Raman spectra along with XRD patterns indicated that at high temperature (above $700^{\circ}C)$, the amorphous $TiO_2was$ segregating to form anatase crystal. Also, the effect of experimental variables such as thermal treatment, heating rate and exposure to water vapor on structural changes, refractive index and thickness of the film coated on sodalime-silicate glass were investigated.