• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.2
• /
• pp.127-132
• /
• 2019

In this paper, we propose a visual inspection method of automotive parts for injection molding to improve the appearance quality and productivity of automotive parts. Exterior inspection of existing injection molding automobile parts was generally done by manual sampling inspection by human. First, we applied the edge-tolerance vision inspection algorithm ([1] - [4]) for vision inspection of electronic components (TFT-LCD and PCB) And we propose a new visual inspection method to overcome the problem. In the proposed visual inspection, the inspection images of the parts to be inspected are aligned on the basis of the reference image of good quality. Then, after partial adaptive binarization, the binary block matching algorithm is used to compare the good binary image and the test binary image. We verified the effectiveness of the edge-tolerance vision check algorithm and the proposed appearance vision test method through various comparative experiments using actual developed equipment.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.9
• /
• pp.3815-3821
• /
• 2012

The LCD frame is an important part which supports the BLU of medium/large sized TFT-LCD. To produce it efficiently, it is necessary to achieve the molding process improvement from 1 cavity to 2 cavity system. Because 2 cavity mold is compact and its hot-runner zone is broadened, it is difficult to control the temperature on the mold. In this study, injection molding analysis on the frame in 2 cavity process with FEA(Finite Element Analysis) software is carried out to estimate its quality. The calculated injection molding pressures and maximum deflection in 1 and 2 cavity processes are 41.13 MPa and 1.62 mm, 40.49 MPa and 1.66 mm respectively. The measured maximum flexure load and surface roughness of the left and right frame of 2 cavities are 209 N and 0.08 ${\mu}m$, 193 N and 0.10 ${\mu}m$ while those in 1 cavity are 140 N and 0.13 ${\mu}m$. Thermal image shows that the maximum standard deviation of the temperature on left and right side of 2 cavity mold is $1.23^{\circ}C$. The simulation and measurement results show that the quality of the frame in 2 cavity injection molding process as a whole is not worse than that of 1 cavity system. But maximum flexure loads of the frame in 2 cavity process are far greater than that in 1 cavity process.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.10a
• /
• pp.477-479
• /
• 2017

With the recent advances in medical technology and health care, the prevention and treatment of diseases has developed. Accordingly aging has rapidly progressed. In this life span and aging society, demand for diagnostic centered medical care is increasing rapidly. In this paper, we propose a wearable patient check system based on FPGA that can be controlled by sensors. In the existing hospital, a doctor or nurse visited the patient every hour to check the condition. However, in this paper, patients, doctors and nurses can check the patient's condition at the desired time using patient check system. In addition, the tilt sensor is used for the patient who is uncomfortable to easily control. The proposed FPGA-based hardware architecture consists of an algorithm for enlarged image processing, a TFT-LCD Controller, a CIS Controller, and a Memory Controller to output the patient's status image. Implemented and validated using the DE2-115 test board with Cyclone IV EP4CE115F29C7 FPGA device and its operating frequency is 50MHz.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.19 no.6
• /
• pp.743-748
• /
• 2009

In this paper, we propose an effective method to extract background components in automated vision inspection system for polarized film used in TFT LCD display panels. The test image signals are typically composed of three components such as ununiform background, random noises and target defect signals. It is important to analyze the background signal for accurate extraction of defect components. Two dimensional continuous wavelets with first derivative gaussian is used. This methods can be applied for reliable extraction of defect signal by elimination of the background signal from the original image. The proposed method outperforms over conventional FFT methods.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.2
• /
• pp.435-442
• /
• 2018

This study implemented an FPGA-based system to extract PCB defect patterns. The FPGA-based system can perform pattern matching at high speed for vision automation. An image processing library that is used to extract defect patterns was also implemented in IPs to optimize the system. The IPs implemented are Camera Link IP, Histogram IP, VGA IP, Horizontal Projection IP and Vertical Projection IP. In terms of hardware, the FPGA chip from the Vertex-5 of Xilinx was used to receive and handle images that are sent from a digital camera. This system uses MicroBlaze CPU. The image results are sent to PC and displayed on a 7inch TFT-LCD and monitor.

• Proceedings of the IEEK Conference
• /
• 2004.08c
• /
• pp.699-702
• /
• 2004

This paper discusses about the mechanism of catching an image through an optical manipulation of each organizations in the eye, more specifically, mechanism of catching an image on a retina through a Camera and a Crystal Lens. In the retina, the macula roles as a fovea contrails and it leads the image which is about 3 mm to be shaped on there. However, even the macula may not properly function, our eyes still can catch the image by shifting the optical path to around of the macula, even if the sensitivity of the image is generally lower than the image on the macula. This paper proposes a method of shifting the shaped image on the retina by refracting the optical path through a prism located on the rear of a screen which consists of a 0.7' TFT LCD. Applying this method that throwing an image around on the macula, central visual disturbance patients among retinitis pimentos patients can expect to recover such a mechanism to catch an image.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.1383-1385
• /
• 2008

In the viewing-angle image control (VIC) technology, one pixel is made up of a quad pixel structure which is consisting of R, G, B, and electrically control briefringence (ECB) sub-pixels. Two types of test stimuli were used; text & complex image respectively. The limitations of those methods were found from the experiment. From the results the advanced GC technology was proposed.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.605-606
• /
• 2008

The distance detection system receives stereo video input through 2 CCD cameras. Using a decoder, the image is changed to the YCbCr4:2:2 format and only the Y signal is saved in the 4*256*8bit shift register of the Dual-Port SRAM. As a result of the matching procedure, the Depth value, which is the distance information, is saved in SRAM, and the Depth Map is made and output to the TFT-LCD screen.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.12
• /
• pp.1742-1745
• /
• 2019

Hidden flame detection after allegedly extinguishing a fire cannot be emphasized enough. There are a few commercial hidden fire detection equipments which are imported, but the cost is relatively high. In this contribution, we propose a development of a low-cost, high-performance hidden flame detector using open-source hardware/software. We use Raspberry-pi based hardware board equipped with a TFT touch-screen LCD, a 3G modem, and an attachable battery device altogether integrated in a plastic case fabricated with a 3D printer. The proposed hidden flame detector shows the same performance of a commercial product FLIR E5 while consuming less than a half of the cost.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.02a
• /
• pp.285-291
• /
• 2002

The shearing process for the sheet metal is normally used in the precision elements such as a frame of TFT-LCD or lead frame of If chips. In these precision elements, the burr formation prevents the system assembly and needs the additional burr removing process. In this paper, we developed the small size NC punching system which has an aligning kinematics between the rectangular shaped punch and die. The punch is driven by an ai cylinder and the sheet metal is moving on the X-Y table system which is driven by two stewing motors. The microprocessor control the whole system and communicate with the monitoring PC by RS232C serial communication protocol. The graphic user interface program in PC monitors nil control the punching system. The cross shaped joint hinge supports the punching die and positioned by two differential screws, whose are installed in perpendicular directions. The aligning between the punch and die is performed using the sheets of half thickness(0.1mm Brass) of the real process for the frame of the TFT-LCD. Using half thickness Brass, the burr formation is magnified and we can decide the aligning direction more easily then using the real thickness(0.2mm) Aluminum. In this paper, the aligning results are measured manually using the SEM photographs and we hope to make the automated aligning procedures using some kinds of image processing techniques.