• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.230-233
• /
• 2006

In this study, the effects of residual stress induced by plastic injection molding process on the tensile behavior of plastic tensile test specimen were investigated. To manufacture plastic tensile test specimens, an injection mold based on the international standard system was designed and made. Cavity pressure and temperature sensors were installed inside of the presented mold to monitor pressure and temperature values during the cycle of injection molding. Injection molding simulation was performed with the same condition of experiment and linear structural tensile analysis was also performed with the initial condition of the residual stress. It was shown that the residual stress induced by injection molding has an effect on the experiment of tensile test and linear structural tensile simulation.

• Proceedings of the KWS Conference
• /
• 2003.05a
• /
• pp.260-262
• /
• 2003

In this study, high temperature tensile properties of high tensile strength steels(POSTEN60, POSTEN80) were investigated by elevated temperature tensile test. According toe the results, high temperature tensile strength of POSTEN60 deteriorated slowly to 100$^{\circ}C$. As the temperature went up the tensile strength became better because of blue shortness and it deteriorated radically after reached to the maximum value around 300$^{\circ}C$. For the POSTEN80, high temperature tensile strength deteriorated slowly to 200$^{\circ}C$.As the temperature went up the tensile strength became better and it deteriorated slowly to 600$^{\circ}C$ after reached to the maximum value around 300$^{\circ}C$. Strain of high tensile strength steels at the elevated temperature increased radically after the mercury rose to 600$^{\circ}C$. The strain hardening ratio of POSTEN60 was larger then that of POSTEN80 at the elevated temperature as in the case at the room temperature and it became smaller radically after the mercury rose to 400$^{\circ}C$.

• Journal of Korea Foundry Society
• /
• v.34 no.6
• /
• pp.194-199
• /
• 2014

The effect of $Al_2Ca$ on the oxidation resistance and tensile property of Al-5Mg alloys was investigated. According to the TGA (Thermogravimetric analysis) result at $550^{\circ}C$ after 24hrs, the Al-5Mg alloy showed parabolic behavior with weight gain. On the other hand, there was almost no difference in the weight changes of the $Al_2Ca$ added Al-5Mg alloys during the oxidation. It was thought that the improvement of oxidation resistance in $Al_2Ca$ added Al-5Mg alloys might be due to the formation of a protective oxide layer with CaO and MgO on the surface. The microstructures of the alloys showed grain refinement with an increasing $Al_2Ca$ content. From the tensile test, the yield strength of the alloys were improved with an increasing $Al_2Ca$ content. The 0.07 mass%$Al_2Ca$ added Al-5Mg alloy showed similar elongation and increased strength, simultaneously. It was considered that the addition of $Al_2Ca$, which was superior in the oxidation resistance of Al, reduced the formation of Mg oxides and inclusions during the alloying. This, partly led to the improvement of tensile properties.

• Journal of Fashion Business
• /
• v.16 no.1
• /
• pp.52-68
• /
• 2012

To achieve the aim of this study, 9 different types of samples were made to examine mechanical property according to structured pattern and type of Machi of pullover armhole of WholeGarment(seamless knitwear). With respect to samples, from which comparisons are made and anaylzed among basic characteristics of material, tensile strength & elongation and residual elongation due to repeated extension of armhole connecting part, the following conclusions could be obtained. It's revealed that the tensile strength of Machi part as being armhole connecting part of samples is more affected by Machi type than pattern structure. Of Machi types, it showed stronger tensile strength in the order of Normal(Normal Machi)< Machi_B(unilateral Machi)

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.322-327
• /
• 2003

In this study, the single notched specimen which was proposed the previous study was used to evaluate of the transverse tensile property of zircaloy cladding. The single notched specimen has notches which give stress intensity effect, so both FEM and experiment are needed for the same time. Take a coincidence of tensile behavior about both FEM and experiment, then obtain stress and strain from FEM only. The influence of notch was estimated by comparing the result of experimental, FEM. Then the relationship between stress-strain and displacement was evaluated.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.04a
• /
• pp.189-192
• /
• 2007

The qualification test of rubber product is consisted of uniaxial tensile, pure shear, biaxial and compression test. Uniaxial test result is used for material property of Finite Element Method. Comparison of uniaxial tensile test and analysis satisfied requirement. A study has qualificated result of QLS analysis model for material property of uniaxial test and shear modulus.

• Journal of Powder Materials
• /
• v.8 no.4
• /
• pp.239-244
• /
• 2001

To investigate the effect of process parameters on selective laser sintering of Cu/polyamide mixed powder, Cu/polyamide mixed powder was sintered by selective laser with changing laser power and scanning speed. The properties of sintered body were evaluated by measuring the density and tensile strength, and analysis of XRD, FT-Raman and microstructure. With an increase in the laser power, the density and ultimate tensile strength of sintered Cu/polyamide body increase and then decrease. The maximum values of the density and ultimate tensile strength were decreased with increasing laser scanning speed. These changes were concerned with the difference of irradiation energy of laser into the powder layer. It was considered that the change of the mechanical property of the sintered body with irradiation energy of laser is due to the changes of amount of copper particle and property of polyamide.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.27 no.8
• /
• pp.883-891
• /
• 2003

In this study, a change of hand of fabrics dyed with persimmon juice was measured using Kawabata Evaluation System. Using various cotton fabrics, linen fabric and silk fabric used frequently for persimmon juice dyeing, we examined the changes of physical properties and hand according to persimmon juice dyeing and washing. The dynamic characteristics of hand were measured tensile, shear, bending, compression, surface properties, thickness and weight. Linearity of load-extention and tensile resilience were increased in all kinds of fabrics after dyeing. Tensile energy decreased in cotton fabric 2(gauze), cotton fabric 3(muslin) and linen fabric. Shear stiffness and hysteresis of shear increased in most of fabrics. Bending rigidity of the bending property and hysteresis of bending, linearity of compression of the compression property, compression energy and compression resilience increased in all kinds of fabrics after dyeing. Thickness and weight increased much in all kinds of fabrics after dyeing. In the primary hand value, stiffness and anti-drape stiffness increased in all kind of fabrics after dyeing. The fullness and softness, crispness, scrooping feeling and flexibility with soft feeling decreased. As the stiffness after persimmons dyeing increased, it was suitable for clothes material of summer.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.33 no.10
• /
• pp.1655-1664
• /
• 2009

Chitosan is an environment-friendly and natural cationic polymer that can be used as a hair cosmetic additive. Healthy hair and damaged hair samples were experimented on according to treatment conditions using a water-soluble chitosan. Chitosan treated hair samples were studied on the physical and mechanical property changes. It is most effective when the water-soluble chitosan treatment was adjusted to the Neutral (pH6.8) or Acid (pH4.5). When the water soluble chitosan was treated at pH4.5, the tensile strength, tensile elongation, and elasticity of decolorized hair all increased. The virgin and damaged hair both changed into elastic and soft hair. The effect of chitosan treatment is more noticeable in the healthy hair than in the damaged hair.

• Journal of Korea Foundry Society
• /
• v.35 no.4
• /
• pp.88-98
• /
• 2015

The effects of quenching and tempering temperatures on the tensile, impact and corrosion properties of A487 alloy cast with different C contents of 0.16, 0.19 to 0.23 wt.% were examined. The impact tests were conducted at $25^{\circ}C$ and $-60^{\circ}C$ and the immersion test was performed using 3.5% NaCl solution for 14 days. The quenching temperature affected the mechanical properties of A487 alloy cast, while the magnitude of change varied depending on the C content. The increase in tempering temperature showed the typical trend of decreasing tensile strength and increasing impact properties. The change in quenching and tempering temperature in this study did not affect the corrosion properties of A487 alloy significantly. The change in mechanical and corrosion properties of A487 with different C contents was discussed based on the microstructural and fractographic observation.