• 보존과학연구
• /
• s.22
• /
• pp.41-52
• /
• 2001

The wooden building is mainly damaged by the termite which have an effect of the structure by making emptied inner part of wood. One class, Japanese termite, inhabits throughout Korea and is often detected. So the deterioration by termite attacking the wooden building needs to be controlled. Termites are over 2,800 species in the world, usually they inhabit in the tropical or subtropical region and don’t over winter in dormant condition. So their activity and distribution are chiefly restricted by temperature and humidity. The termite inhabiting in Korea is Reticulitermes speratus kyushuensis Morimoto, which known to have an optimal temperature range at $12~30^{\circ}C$ and minimum temperature at $6^{\circ}C$ for activation. These temperatures correspond to the mean temperature($5.6^{\circ}C$~$25.8^{\circ}C$) from March to November and the activity time of termitein Seoul. In addition, as a result of environmental pollution by industrial development, the climate of Korea is getting warm. The increase of mean temperature in Korea has been $1.1^{\circ}C$ for the past seventy five years, so it is expected that the damage of wooden building by termite will increase gradually. Therefore, in order to protect wooden building from damages by termite, it needs not only development of new pest control methods, but also studies on the control of environmental factors having an effect on the activity and growth of termite. For the conservation of the large cultural properties such as the wooden building in the open air, it would be effective to use the methods of fumigation, insecticidal and antiseptic chemical treatment of wood materials, soil termiticideinjection treatment, and termite colony elimination system.

• Asian-Australasian Journal of Animal Sciences
• /
• v.9 no.3
• /
• pp.341-347
• /
• 1996

An experiment was conducted to evaluate the effects of dietary levels of chromium in the form of chromium picolinate on growth performance, nutrient utilizability, carcass composition, serum traits, and in vitro lipolysis and lipogenesis in adipose tissues of Arbor Acre broiler chicks. Experimental diets containing six different levels of chromium (0, 100, 200, 400, 600 and 800 ppb) were fed for 6 weeks. Individual treatment had six replicates of eight birds each and their average initial weight was 59.2 g. Dietary addition of chromium did not affect growth performance and nutrient utilizability. However, mortality appeared to be reduced with addition of chromium to the diet. It was obvious that chromium supplementation significantly decreased serum cholesterol and increased serum HDL cholesterol (p < 0.05), but serum insulin, glucose, triglyceride and non-esterified fatty acid concentrations were inconsistent among dietary supplementation levels of chromium. The in vitro lipolysis and lipogenesis in adipose tissues were significantly influenced by dietary addition of chromium (p < 0.05). Chicks fed diets containing 200 or 400 ppb chromium showed the highest protein content and the lowest fat content in their carcass.

• Journal of Korea Multimedia Society
• /
• v.15 no.2
• /
• pp.234-241
• /
• 2012

The purpose of this study is to analyze the economic effects of telepresence system for public sector relocation. As a Green IT system, the importance of telepresence is being recognized increasingly as a means to replacing a majority of business trips and thereby reducing greenhouse gases emitted in the process. However, there are only a few related researches that analyze the economic effects of telepresence at the moment. This study conducts the cost-benefit analysis of 157 public sectors which are to relocate from 2012 based on the sample case of National Information Society Agency. The results obtained reveals that telepresence would save about 180 billion won and reduce about 580t $CO_2$ emission. This study are expected to provide the academic framework for organizations contemplating the adoption of Green IT system moving forward.

• Journal of the Korean Dietetic Association
• /
• v.4 no.1
• /
• pp.88-98
• /
• 1998

The purposes of this research were to assess the quality of worklife of university foodservice managers and workers by operation type, and to investigate the characteristics of demographic variables in university foodservice employees. A questionnaire was administered to 27 managers and 180 personnels who are working in 9 university foodservice facilities. And 21 managers and 160 workers were responded with a response rate of 78% and 89%, respectively. Statistical data analysis was completed using the SPSS programs for descriptive analysis, ANOVA, T-test and SNK test. The results of this study can be summarized as follows : 1. Almost all respondents were female(87%), 40.5 percent of the respondents were between 40 to 49 years of age, 42.9 percent of the respondents had been in their current job between 2 to 5 years, and 55.2 percent of the respondents earned ays between 500,000won to 800,000won per month, Only 42.6% percent of the respondents were full-time employee. 2. The mean scores for the quality of worklife was 3.07 on a 5-point scales of 1=disagree very much and 5 = agree very much. 3. Factors receiving the higher ratings included "optimum levels of work variety"(3.83), "positive attitude toward work"(4.14), and " cooperative relationship with coworkers"(4.22). But respondents were least satisfied with "promotion"(2.07),"temperature of workplace"(2.17) " rest time"(2.25), and "pay"(2.28) factors. 4. There was a significant difference in the perception of the quality of worklife according to the operation type(self-operated, contracted, and rented management), but no difference was noted by position(managers vs workers) Results can be user to develop intervention and training strategies for enhancing positive attitude and the quality of work of employees.

• Asian-Australasian Journal of Animal Sciences
• /
• v.30 no.9
• /
• pp.1270-1277
• /
• 2017

Objective: The present study aimed to determine the impact of ewe body condition score (BCS) (over a range of 2.0 to 3.0) and nutritional treatments (consisting of differing herbage masses) during very late pregnancy and lactation and their potential interaction on the performance of twin-bearing ewes and their lambs to weaning. Methods: On day 142 of pregnancy, twin-bearing ewes with a BCS of 2.0, 2.5, or 3.0 were allocated to a "Moderate' or 'Unrestricted' nutritional treatment until day 95 of lactation (weaning). The nutritional treatments aimed to achieve average herbage masses of 1,200 to 1,300 kg dry matter (DM)/ha (Moderate) and 1,500 to 1,800 kg DM/ha (Unrestricted). Results: There were no three-way interactions between ewe BCS group, nutritional treatment and time for any ewe or lamb parameter. The nutritional treatments had no effect (p>0.05) on lamb birth or weaning weight. Lambs born to Moderate ewes had greater survival and total litter weight at weaning (p<0.05). Regardless of BCS group, Unrestricted treatment ewes had greater body condition and back-fat depth at weaning than Moderate treatment ewes (p<0.05). Ewes of BCS 2.0 group reared lighter lambs to weaning (p<0.05) and tended to have a lower total litter weight (p = 0.06) than BCS 3.0 group ewes. Conclusion: This study suggests farmers should aim to have all ewes with a BCS of 2.5 or 3 in late pregnancy for optimal lamb weaning performance. Furthermore, there is no benefit to lamb production of offering ewes pasture masses >1,200 kg DM/ha during very late pregnancy and lactation.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.1
• /
• pp.104-111
• /
• 2009

This paper shows the behaviors of macro- and micro-structures and mechanical properties for specimen's welding region welded by FSW. according to welding conditions with 5mm thickness aluminum 5083O alloy plate. It apparently results in defect-free weld zone in case traverse speed was changed to 32 mm/min under conditions of anti-clockwise direction and tool rotation speed such as 800 and 1250 rpm with tool's pin diameter of 5 ${\Phi}mm$ and shoulder diameter of 20 ${\Phi}mm$, pin length of 4.5 mm and tilting angle of $2^{\circ}$. The ultimate stress of ${\sigma}_T=331$ MPa and the yield point of 147 MPa are obtained at the condition of the travel speed of 32 mm/min with the tool rotation speed of 1250 rpm. There is neither voids nor cracks on bended surface of $180^{\circ}$ after bending test. The improvement of toughness after impact test was found. The lower rotating and traverse speed became, the higher were yield point, maximum stress and elongation(%) with the stresses and the elongation(%) versus the traverse speed diagram. Vickers hardness for cross section of welding zone were also presented. The typical macro-structures such as dynamically recrystallized zone, thermo-mechanically affected zone and heat affected zone and the micro-structures of the transverse cross-section were also showed. However, the author found out that the region of 6mm far away from shoulder circumference was affected by friction heat comprehensively, that is, hardness softened and that part of micro-structures were re-solid-solution or recrystallized, the author also knew that there is no mechanically deformation on heat affected zone but there are the flow of plastic deformation of $45^{\circ}$ direction on thermo-mechanically affected zone and the segregation of Al-Mg on nugget. The solid solution wt(%) of parent material as compared against of friction stir welded zone was comprehensively changed.

• Journal of Life Science
• /
• v.14 no.3
• /
• pp.521-524
• /
• 2004

This experiment was carried out to analyze genetic characteristics and to develop the breed specific DNA marker for Cheju-native horse. If this marker contains high repetitive sequences, it is possible to convert a RAPD marker of interest into a single-locus PCR marker called a sequence characterized amplified region(SCAR). Twenty six Cheju-native horse and Fifty thoroughbred genomic DNA were pooled and PCR. were accomplished using 800 random primers. Comparing the pooled DNA from Cheju-native horse and thoroughbred, we found 9 primers which identified markers present in the pooled DNA from breed but absent in the other breed. Among 9 random primers, 6 primers were thoroughbred specific and 3 primers were Cheju-native horse specific. Testing individual horse revealed that 5 marker showed the similar band pattern between Cheju-native horse and Thoroughbred. However, 4 marker were wholly absent in breed while present in the other breed. UBC $126_{3500bp}$, UBC $162_{500bp}$, and UBC $244_{1200bp}$ was detected only Thoroughbred and UBC $562_{560bp}$was detected Cheju-native horse, respectively. After determining of the cloned breed-specific fragment sequence, we designed the SCAR-primers and carried out PCR. Compared to random primer, RAPD-SCAR primer didn't show significantly higher specific band. However, RAPD analysis is useful for genetic characterization of Cheju-native horse.

• Journal of Advanced Marine Engineering and Technology
• /
• v.21 no.5
• /
• pp.535-541
• /
• 1997

The effect of concentration of each solution( HCI, $H_2SO_4$ and $HNO_3$), scan rate and polished surface condition on the corrosion of AISI 304 Stainless Steel were investigated, utilizing the Method ASTM G5 - 87. It can be concluded that: 1) For the same concentration(i.e. 1N) of each solution the corrosion rate is the highest in HCI and lowest in $HNO_3$. Also, the difference of values of $i_{cirt}$ generated for each solution is significant. 2) As the concentration of the solution $H_2SO_4$ is increased (O.5N, 1N, 2N) the values of $E_{cor}$ $i_{crit}$ and $i_{p}$ are increased. 3) In case of existence of SCN ion of O.OlN, the values of iCTIt and ip generated are approximately 100 times and 1.4 times higher respectively, than in the case of non - existence of $SCN^{-}$. However the existence of $SCN^{-}$ doesn't affect the value of $E_{cor}$ and $E_{p}$. 4) The values of $i_{crit}$ and $i_{p}$ are increased due to the increase of scan rate. But the values of $E_{cor}$ and $E_{p}$ do not depend on the scan rate. 5) The $i_{p}$ value depends greatly on oxygen in the solution, but the changes in values of $E_{cor}$ $i_{crit}$ and $E_{b}$ due to the oxygen are insignificant. 6) If a component is polished using #400, #600 and #800 wet polish paper, the effect of surface condition on variations of values of $i_{crit}$ and $i_{p}$ is slightly significant.

• Textile Coloration and Finishing
• /
• v.18 no.3 s.88
• /
• pp.49-58
• /
• 2006

The purpose of this study was to examine the effect of covering yarn's twist on mechanical properties of knitted fabrics of composite yarns with single covering process. Four yarns that were used in this study: two different composite yarns made from the four kinds of cotton and functional polyester-(Poly-A) with the ratio of 52:48, and the rest two yarns are the original cotton 100% yarn and the poly-A 100% yarn. The two kinds of composite yarns, CP1 and CP2, were processed on the single covering process. CP1 was applied on the single covering process with S-800 tpm, where Poly-A was used as covering yarn and cotton was used as core yarn. CP2 was applied on the same process as CP1 except that Poly-A had been applied on the two-for-one twisting process with S-400 tpm on the previous step. Sixteen mechanical properties of all the four knifed fabrics knitted under the same knitting conditions were measured by KES-FB system with the outer knit condition. And 3D CAD dressmaking simulations, which were driven by some of the mechanical properties, were presented. The results were as follows: CP2 had high RT values with twisting of covering yarn. CP2 also had high B, 2HB values because of higher linear density. SMD was affected rather by twisting of covering yarn than by fine hair of the cotton surface. Twisting of covering yarn made it decreasing T value and increasing W value. Dressmaking 3D CAD simulations showed that there are buckling effects on CP2 because of high bending rigidity and shear rigidity.

• ALGAE
• /
• v.29 no.1
• /
• pp.35-45
• /
• 2014

Palmaria palmata was integrated with Atlantic halibut Hippoglossus hippoglossus on a commercial farm for one year starting in November, with a temperature range of 0.4 to $19.1^{\circ}C$. The seaweed was grown in nine plastic mesh cages (each $1.25m^3$ volume) suspended in a concrete sump tank ($46m^3$) in each of three recirculating systems. Two tanks received effluent water from tanks stocked with halibut, and the third received ambient seawater serving as a control. Thalli were tumbled by continuous aeration, and held under a constant photoperiod of 16 : 8 (L : D). Palmaria stocking density was $2.95kg\;m^{-3}$ initially, increasing to $9.85kg\;m^{-3}$ after a year. Specific growth rate was highest from April to June (8.0 to $9.0^{\circ}C$), 1.1% $d^{-1}$ in the halibut effluent and 0.8% $d^{-1}$ in the control, but declined to zero or less than zero above $14^{\circ}C$. Total tissue nitrogen of Palmaria in effluent water was 4.2 to 4.4% DW from January to October, whereas tissue N in the control system declined to 3.0-3.6% DW from April to October. Tissue carbon was independent of seawater source at 39.9% DW. Estimated tank space required by Palmaria for 50% removal of the nitrogen excreted by 100 t of halibut during winter is about 29,000 to $38,000m^2$, ten times the area required for halibut culture. Fifty percent removal of carbon from the same system requires 7,200 to $9,800m^2$ cultivation area. Integration of P. palmata with Atlantic halibut is feasible below $10^{\circ}C$, but is impractical during summer months due to disintegration of thalli associated with reproductive maturation.