• Journal of Welding and Joining
• /
• v.28 no.4
• /
• pp.81-86
• /
• 2010

In resistance spot welding, regardless of the optimal condition, bad weld quality was still produced due to complicated manufacturing processes such as electrode wear, misalignment between the electrode and workpiece, poor part fit-up, and etc.. Therefore, the goal of this study was to measure the process signal which contains weld quality information, and to develop the process fault monitoring system. Welding force signal obtained through variety experimental conditions was analyzed and divided into three categories: good, shunt, and poor fit-up group. And then a monitoring algorithm made up of an artificial neural network that could estimate the process fault of each different category based on pattern was developed.

• Proceedings of the KWS Conference
• /
• 2008.05a
• /
• pp.49-49
• /
• 2008

• Proceedings of the KWS Conference
• /
• 2005.06a
• /
• pp.63-65
• /
• 2005

Because of simple principal and low cost, resistance spot welding has been used a lot for joining the sheet metal in automotive manufacturing process. Welding current, welding time, and force are the most important variables in resistance spot wording. Air guns have hem still used widely. The requirement of synchronizing between robot and weld-gun has become bigger as the field has been automated. The number of servo-gun in the field is trending upward because there're advantages as like to synchronize with robot and to control the stroke path and force by programming on servo-gun system. But no cleared force control method is suggested on servo-gun system until now. In this study, we proved the feedback current of the servo-motor can be used to an excellent force measuring sensor and the force is controlled by the feedback current. And we also detected force lowering during welding cycle on the servo-gun system and solved by compensated force control.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.4
• /
• pp.384-394
• /
• 2002

In this paper, a new control strategy is proposed to improve the quality of the welding products. The conventional nonlinear power control system of spot welders is linearized using nonlinear feedback linearization technique based on differential geometry theory. An evolution strategy(ES) geometry is used to find optimal gain of PI controllers. It tries to find out the optimal control parameters by imitating the natural evolution. Some Simulation and experimental results show that the proposed variable power control system using ES algorithm has better dynamic performances than the conventional one.

• Journal of Advanced Marine Engineering and Technology
• /
• v.12 no.1
• /
• pp.37-45
• /
• 1988

A calculating method of transient temperature distribution due to spot welding of thin plates is studied in this paper. Considering the contact stress between upper and lower plate and temperature-dependence of specific resistance and elastic limit of base metal, the model of calorific density of heat source was decided. Using 2-dimensional polar coordinates system, the governing equation of heat transfer was developed. The thermal cycles of various points were recorded using C-A thermocouples during spot welding procedure for mild steel plates of 1mm thickness, and those results were compared with the results of calculations presented in this paper.

• Proceedings of the KIEE Conference
• /
• 1997.07b
• /
• pp.406-408
• /
• 1997

This paper presents the new method of a nondestructive spot welding state inspection system using neural networks. The learning process of neural networks makes the inspection system to adapt the variable welding parameters. The inspecting process is working with on-line real-time after off-line learning process. This neural network based inspection system shows reliable results through the field test for variations of applied voltages, currents, and contact area of the welding electrode.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.4
• /
• pp.119-125
• /
• 2008

A new type of swivel unit is suggested in order to complement weak points of the existing. This new type of Swivel unit is developed by adopting a spring type cable which has elasticity and restoring force. To minimize the troubles in the process of manufacturing during operating the new type system, strength analysis and the check of interference between parts are accomplished with CATIA. The check of rotating performance is also carried out to determine the diameter and length of spring type cable by SimDesigner motion analysis. Swivel unit used in the robot spot welding is developed with spring type cable and its usefulness in the industrial field is verified through experiments. This system has been registered for patent.

• Journal of Power System Engineering
• /
• v.19 no.2
• /
• pp.70-77
• /
• 2015

Nowadays, car manufacturers applied many high strength steels such AHSS or UHSS to car bodies for weight lightening. Therefore, a variety of applied steel sheet to car bodies increased and the needs of simulation to evaluate weldability also increased in order to reduce the cost and time. In this study, resistance spot welding simulations for DP 780 Steel with 1.0 and 1.4 mm thickness were conducted with respect to lobe curve. 2 regression models to estimate tensile shear strength were suggested and they were second order polynomial regression model and optimized second order regression model. The performance of these models was evaluated in terms of the coefficient of determinant and average error rate.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.117-120
• /
• 2001

Resistance spot welding is widely employed in a manufacturing process. In recent years, the requirement for more sophisticated quality control procedures has been in the mass production industries. The requirements for high productivity and good welding qualities have lead to the development of more widely available microprocessor or computer based control. In this study, the inverter-type power source and welding servo gun are developed.

• Proceedings of the KWS Conference
• /
• 2003.11a
• /
• pp.132-134
• /
• 2003