• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 B
• /
• pp.684-686
• /
• 2000

Switched reluctance motor(SRM) has the advantages of simple structure, low rotor inertia. and high efficiency. However position sensor is essential in SRM in order to synchronize the phase excitation to the rotor position. The position sensors increase the cost of drive system and tend to reduce system reliability. This paper investigates the speed control of sensorless SRM in which the phase current and change rate are utilized in position decision, and the period of dwell angle is variable by compensating the rotor angle for speed control. The proposed system consists of position decision. phase locked loop controller, switching angle controller and inverter. The performances in the proposed system are verified through the experiment.

• 반도체디스플레이기술학회지
• /
• 제14권4호
• /
• pp.72-77
• /
• 2015

Three-level diode clamped multilevel inverter, generally known as neutral point clamped (NPC) inverter, has an inherent problem causing neutral point (NP) potential variation. Until now, the NP potential problem of variation has been investigated and lots of solutions have also been proposed. This paper presents a neutral point voltage control technology using the anti-windup PI controller and offset technology of PWM (Pulse Width Modulation) to control the variation of NPC 3-phase three-level inverter neutral point voltage. And the proposed algorithm is tested and verified using a PLL (Phase Locked Loop) in order to synchronize the phase voltage from the line voltage of grid. It significantly improves the voltage balancing under a solar fluctuation conditions of the inverter. Experimental results show the good performance and effectiveness of the proposed method.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2017년도 전력전자학술대회
• /
• pp.266-267
• /
• 2017

To synchronize the distributed generation (DG) unit with the grid, the voltage sensors are generally employed to obtain the grid phase angle. This paper presents an observer-based voltage sensorless control scheme for a three-phase inverter connected to the grid through an LCL filter. The proposed control scheme consists of an augmented state observer and a feedback controller. The augmented state observer is used to estimate the grid voltages and states of the inverter system, which are then employed to determine the grid voltage angle and to construct the feedback controller. As a result of using the observer, only the grid current sensors are required to accomplish the control scheme. The simulation results are given to prove the validity of the proposed control scheme.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2007년도 Proceedings of ISRS 2007
• /
• pp.130-133
• /
• 2007

In order to get high quality and high resolution image data from the space-borne camera system, the image chain from the sensor to the user in the ground-station need to be designed and controlled with extreme care. The behavior of the camera system needs to be controlled by ground commands to support on-orbit calibration and to adjust imaging parameters and to perform early stage on-orbit image correction, like gain and offset control, non-uniformity correction, etc. The operation status including the temperature of the sensor needs to be transferred to the ground-station. The preparation time of the camera system for imaging with specific parameters should be minimized. The camera controller needs to synchronize the operation of cameras for every channel and for every spectral band. Detail timing information of the image data needs to be provided for image data correction at ground-station. In this paper, the design of the camera controller for the AEISS on KOMPSAT-3 will be introduced. It will be described how the image chain is controlled and which imaging parameters are to be adjusted The camera controller will have software for the flexible operation of the camera by the ground-station operators and it can be reconfigured by ground commands. A simple concept of the camera operations and the design of the camera controller, not only with hardware but also with controller software are to be introduced in this paper.

• 한국정밀공학회지
• /
• 제32권8호
• /
• pp.719-726
• /
• 2015

This paper presents a velocity-synchronizing control for the multiple axes of an injection unit; based on MBS, a virtual design model has been developed for the multiple-axes servomechanism. Prior to the design of the controller, a linear plant model was derived via open-loop response simulations. To synchronize the motions of the multiple axes, a cross-type synchronizing controller was designed and combined with the PID control to accommodate any parameter mismatches among the multiple axes. From the tracking control simulations, a significant reduction of both velocity-tracking and position-tracking errors was achieved through the use of the proposed control scheme.

• 전기전자학회논문지
• /
• 제2권2호
• /
• pp.166-172
• /
• 1998

스위치드 리럭턴스 전동기는 구조가 간단하고 회전자관성이 작으며 고효율을 가지는 전동기이다. 그러나 회전자 위치각에 적절한 상여자 신호를 동기화하기 위해서는 위치센서가 필수적이다. 이 위치센서로 인하여 구동시스템의 가격상승과 열악한 환경에서 시스템의 신뢰성이 저하되는 문제점을 가지게 된다. 본 논문에서는 위치 및 속도센서가 없는 스위치드 리럭턴스 전동기의 속도제어 시스템을 연구하였다. 센서리스 SRM의 안정된 속도제어를 위하여 회전자 위치검출을 상전류 및 변화율 검출로부터 구하였으며 속도오차에 대하여 도통각 주기폭을 변동하는 속도제어 시스템을 제안하였다. 이 구동시스템은 위치결정회로 속도제어기, 디지탈논리 정류자, 스위칭각 제어기와 인버터로 구성된다. 제안된 시스템은 실험을 통하여 성능을 검증하였다.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 춘계학술대회 논문집
• /
• pp.190-198
• /
• 2002

In switched reluctance motor(SRM) drive, it is necessary to synchronize the stator phase excitation with the rotor position. Therefore the rotor position information is an essential. Usually optical encoders or resolvers are used to provide the rotor position information. These sensors are expensive and are not suitable for high speed operation. In general, the accuracy of the switching angles is dependent upon the resolution of the encoder and the sampling period of the microprocessor. But the region of high speed, switching angles are fluctuated back and forth from the preset values, witch are cause by the sampling period of the microprocessor. Therefore, the low cost linear encoder suitable for the practical and stable SRM drive is proposed and the control algorithm to provide the switching signals using the simple digital logic circuit is also presented in this paper It is verified from the experiments that the proposed encoder and logic controller can be a powerful candidate for the practical low cost SRM drive.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.16-18
• /
• 2003

In a switched reluctance motor drive, it is important to synchronize the stator phase excitation with the rotor position, because the position of rotor is an essential information. In the high-speed region, switching angles are fluctuated back and forth out of the preset value, which is caused by the sampling period of the microprocessor. In this paper, a low cost analog encoder suitable for practical applications is proposed. The validity of the proposed analog encoder with a proper logic controller is verified from the experiments.

• International Journal of Precision Engineering and Manufacturing
• /
• 제4권1호
• /
• pp.9-14
• /
• 2003

In this study we suggest real-time simulator that could describe rent system without ordinary DSP card. This simulator is composed of 80196kc-16bit ordinary microprocessor, which is widely used up to now and personal computer. DSP card that has calculated complex numerical equation is replaced by personal computer and 80196kc generates control signals independently out of the personal computer. In all process personal computer is synchronized with one-board microprocessor (80196kc) within sampling time in the closed loop system. This makes it possible to be described in hydraulic servo system in real time.

• 전기학회논문지
• /
• 제58권3호
• /
• pp.605-613
• /
• 2009

In this paper, we studied for the real-time azimuthal measurement of HMD (Head Mounted Display) to control the tele-operated vision system on the mobile robot. In the preexistence tele-operated vision system, a joystick was used to control the pan-tilt unit of the remote camera system. To give the sense of presence to the tele-operator, we used a HMD to display the remote scene, measured the rotation angle of the HMD on a real time basis, and transmitted the measured rotation angles to the mobile robot controller to synchronize the pan-tilt angles of remote camera with the HMD. In this paper, we suggest an algorithm for the real-time estimation of the HMD rotation angles using feature points extraction from pc-camera image. The simple experiment is conducted to demonstrate the feasibility.