• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.42 no.2
• /
• pp.291-298
• /
• 2017

In this paper, we derive the achievable degrees of freedom (DoF) for multiple-input multiple-output (MIMO) Z-interference channels (Z-IC) with reconfigurable antennas at the receivers, assuming that channel state information is not available at the transmitters. We propose a new linear scheme to align interfering signals and to decode desired signals through the designed preset mode switching pattern of reconfigurable antennas at the receivers. The key idea of our scheme is to use interfering signals as a side information at the interfered receiver by being silent at the corresponding transmitter during some time slots. Consequently, it is shown that the reconfigurable antennas at the receivers can bring a DoF gain if the number of preset modes is greater than the number of RF chains at the receivers.

• Journal of IKEEE
• /
• v.12 no.1
• /
• pp.59-64
• /
• 2008

In this paper, a new efficient SMPS has been designed and implemented. It can replace the existing product that is widely used in industry. To investigate the performance of the conventional SMPS, the output voltage changes due to variations in the input voltage and the load conditions, and the ripple and noise voltages have been measured and analyzed. As a result, it has been confirmed that the noise in the conventional SMPS is severe due to the deficiency of patterns for current. This is because the conventional SMPS draw out all outputs using one transformer and the alarm logic exists in the output path. To solve this problem, the switching frequency is increased from 17KHz to 70KHz and the current patterns are fully guaranteed by separating the alarm circuit and PWM circuit as a sub-board from the main board. Measurement results shows that the output noise of the designed SMPS decreases below 32% of the conventional SMPS noise for various test conditions, and both the line and load regulations are improved.

• Convergence Security Journal
• /
• v.13 no.3
• /
• pp.25-31
• /
• 2013

Looking at the recent value change of users and the usage pattern of network users, it is changing from simple web information, one-way information acquisition and data transmission to increase of usage of multimedia, increasing demand for security and customization, and increasing demands for free mobility. Due to this change of demand, the services which were provided individually, developed into a form which is merged, the network also seems to develop into the combined network from the individual network for individual service, and the communication network control technology which is the core technology is also rapidly developing. To reflect the users' demands, the next generation network created the multi-layer network which is based on the WDM/IP transmission system and added the to make it easy to restructure. P-OTS (Packet-Optical Transport System) can be defined as a platform that combines SONET/SDH, Ethernet, DWDM, optical transport network (OTN) switching and reconfigurable optical add-drop multiplexers (ROADMs). In this paper, we suggested that the optimum path choice be performed through diversification of the PCE-based path selection using the information of various layers altogether in the multi-layer environment, compared with the established path selection method when the path was selected using the information of each layers.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.3
• /
• pp.75-84
• /
• 2005

Since an unexpected fault of induction motor drive systems can cause serious troubles in many industrial applications, which the technique is required to diagnose faults of a voltage-fed PWM inverter for induction motor drives. The considered fault types are rectifier diodes, switching devices and input terminals with open-circuit faults, and the signal for diagnosis is derived from motor currents. The magnitude of dq-current trajectory is used for the feature extraction of a fault and PCA LDA are applied to diagnose. Also, we show results with respect to the execution time because of the possibility to use that a diagnosis software is embedded in the controllers of medium and small size induction motors drive for real-time diagnosis. After we performed various simulations for the fault diagnosis of the inverter, the usefulness of proposed algerian was verified.

• Proceedings of the Korean Information Science Society Conference
• /
• 2004.04b
• /
• pp.541-543
• /
• 2004

능동적 학습(active learning)은 제한된 시간과 인력으로 가능한 정확도가 높은 분류기(classifier)를 생성하기 위하여, 훈련집합에 추가할 예제 즉 문의예제(query example)의 선정과 확장된 훈련집합으로 다시 학습하는 과정을 반복하여 수행한다. 능동적 학습의 핵심은 사용자에게 카테고리(category) 부여를 요청할 문의예제를 선정하는 과정에 있다. 효과적인 문의예제를 선정하기 위하여 다양한 방안들이 제안되었으나, 이들은 매 문의단계마다 하나의 문의예제를 선정하는 경우에 가장 적합하도록 고안되었다. 능동적 학습이 복수의 예제를 사용자에게 문의할 수 있다면, 사용자는 문의예제들을 서로 비교해 가면서 작업할 수 있으므로 카테고리 부여작업을 보다 빠르고 정확하게 수행할 수 있을 것이다. 또한 충분한 인력을 보유한 상황에서는, 카테고리 부여작업을 병렬로 처리할 수 있어 전반적인 학습시간의 단축에 큰 도움이 될 것이다. 하지만, 각 예제의 문의예제로써의 적합 정도를 추정하면 유사한 예제들은 서로 비슷한 수준으로 평가되므로, 기존의 방안들을 복수의 문의예제 선정작업에 그대로 적용할 경우, 유사한 예제들이 문의예제로 동시에 선정되어 능동적 학습의 효율이 저하되는 현상이 나타날 수 있다. 본 논문에서는 특정 예제를 문의예제로 선정하면 이와 일정 수준이상 유사한 예제들은 해당 예제와 함께 문의예제로 선정하지 않음으로써, 이러한 문제점을 극복할 수 있는 방안을 제안한다. 제안한 방안을 문서분류 문제에 적용해 본 결과 기존 문의예제 선정방안으로 복수 문의예제를 선정할 때 발생할 수 있는 문제점을 상당히 완화시킬 있을 뿐 아니라, 복수의 문의예제를 선정하더라도 각 문의 단계마다 하나의 예제를 선정하는 경우에 비해 큰 성능의 저하가 없음을 실험적으로 확인하였다./$m\ell$로 나타났다.TEX>${HCO_3}^-$ 이온의 탈착은 서서히 진행되었다. R＆D investment increases are directly not liked to R＆D productivities because of delays and side effects during transition periods between different stages of technology development. Thus, It is necessary to develope strategies in order to enhance efficiency of technological development process by perceiving the switching pattern. 기여할 수 있을 것으로 기대된다. 것이다.'ity, and warm water discharges from a power plant, etc.h to the way to dispose heavy water adsorbent. Through this we could reduce solid waste products and the expense of permanent disposal of radioactive waste products and also we could contribute nuclear power plant run safely. According to the result we could keep the best condition of radiation safety super vision and we could help people believe in safety with Radioactivity wastes control for harmony with Environ

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.11
• /
• pp.1687-1695
• /
• 2021

In this paper, it is designed and analyzed the beamforming antenna using the butler matrix. The operating frequency of the proposed beamforing antenna is ISM band of 2.4 GHz band and the component of the beamforing antenna consisted of a 1×4 array antenna and a 4×4 butler matrix. Each output port of 4×4 butler matrix outputs the signal having a different phase, it is provided to each input port of 1×4 array antenna. The beamforming antenna with four output ports forms a total of four beams. In order to analyze the radiation pattern of the beamforming antenna, it was provided by switching the signal to the input port and proceeded the Individual analysis for the input port 1 to 4. The main beams of the proposed beamforming antenna were formed in the -12°, 40°, -40° and 12° directions according to each input port, respectively.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.10 no.3
• /
• pp.199-205
• /
• 2017

In a small cell base station used in densely populated areas, a dual polarized multiple antenna(MIMO) is mainly used to increase the cell capacity. This paper demonstrates a dual-polarization antenna with high cross-polarization discrimination(XPD) that can improve the capacity of a small cell using a dual polarization multiple antenna (MIMO). By using the symmetric structure and differential feeding, high XPD in all directions is achieved. In addition, a very similar radiation pattern is observed between each polarization. Because of high XPD and similar radiation pattern in all directions, proposed antenna is well adopted for small-cell multiple-input multiple-output(MIMO) system. Experimental results shows that the proposed antenna has a bandwidth of 180 MHz (2.51~2.7 GHz), a maximum gain of 4.5 dBi (3.5~4.5 dBi), and a half-power beam width of 85 degrees. In addition, average XPD of 26.4 dB in all directions, more than 13.8 dB increase than previous dual-polarization antennas which use single emitter by using different feeding or selectively use polarization through switching.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.183-184
• /
• 2013

Two main MBE growth techniques have been used: plasma-assisted MBE (PA-MBE), which utilizes a rf plasma to supply active nitrogen, and ammonia MBE, in which nitrogen is supplied by pyrolysis of NH3 on the sample surface during growth. PA-MBE is typically performed under metal-rich growth conditions, which results in the formation of gallium droplets on the sample surface and a narrow range of conditions for optimal growth. In contrast, high-quality GaN films can be grown by ammonia MBE under an excess nitrogen flux, which in principle should result in improved device uniformity due to the elimination of droplets and wider range of stable growth conditions. A drawback of ammonia MBE, on the other hand, is a serious memory effect of NH3 condensed on the cryo-panels and the vicinity of heaters, which ruins the control of critical growth stages, i.e. the native oxide desorption and the surface reconstruction, and the accurate control of V/III ratio, especially in the initial stage of seed layer growth. In this paper, we demonstrate that the reliable and reproducible growth of GaN on Si (110) substrates is successfully achieved by combining two MBE growth technologies using rf plasma and ammonia and setting a proper growth protocol. Samples were grown in a MBE system equipped with both a nitrogen rf plasma source (SVT) and an ammonia source. The ammonia gas purity was ＞99.9999% and further purified by using a getter filter. The custom-made injector designed to focus the ammonia flux onto the substrate was used for the gas delivery, while aluminum and gallium were provided via conventional effusion cells. The growth sequence to minimize the residual ammonia and subsequent memory effects is the following: (1) Native oxides are desorbed at $750^{\circ}C$ (Fig. (a) for [$1^-10$] and [001] azimuth) (2) 40 nm thick AlN is first grown using nitrogen rf plasma source at $900^{\circ}C$ nder the optimized condition to maintain the layer by layer growth of AlN buffer layer and slightly Al-rich condition. (Fig. (b)) (3) After switching to ammonia source, GaN growth is initiated with different V/III ratio and temperature conditions. A streaky RHEED pattern with an appearance of a weak ($2{\times}2$) reconstruction characteristic of Ga-polarity is observed all along the growth of subsequent GaN layer under optimized conditions. (Fig. (c)) The structural properties as well as dislocation densities as a function of growth conditions have been investigated using symmetrical and asymmetrical x-ray rocking curves. The electrical characteristics as a function of buffer and GaN layer growth conditions as well as the growth sequence will be also discussed. Figure: (a) RHEED pattern after oxide desorption (b) after 40 nm thick AlN growth using nitrogen rf plasma source and (c) after 600 nm thick GaN growth using ammonia source for (upper) [110] and (lower) [001] azimuth.

• Journal of Mushroom
• /
• v.2 no.3
• /
• pp.115-126
• /
• 2004

Somatic hybrids of inter-compatible and inter-incompatible strains were obtained by protoplast fusion. The fusion products between compatible strains, Pleurotus ostreatus and P. florida, formed heterokaryons, while fusants between incompatible strains such as P. cornucopiae + P. florida, P. ostreatus + Ganoderma applanatum, P. florida + Ganoderma lucidum, and P. ostreatus + Flammulina velutipes formed synkaryons that retained genes from both parents. The heterokaryons showed the same level of basidioma development. In contrast, the synkaryons showed unique characteristics including clamp connection formation at mitosis, either partner basidioma development, and abnormal segregation and recombination compared with inter-compatible strains. Synkaryons can be classified into homokaryoyic and heterokaryotic type. A comparison of somatic hybrids with compatible and incompatible strains was made using random amplified polymorphic DNA (RAPD) analysis. The heterokaryons between compatible species showed the same level of variability and contained both parental RAPD bands. In contrast, most of the synkaryons between incompatible species showed similarity to those of either parental bands and non-parental RAPD bands. Synkaryons can be classified into microgenome insertion type and macrogenome insertion type. A tetrapolar mating system was found among monospore isolates in somatic hybrids and wild type P. ostreatus. Homokaryons from each somatic hybrid combination were paired with tester homokaryons of the initial wild type of P. ostreatus. The changed mating types were identified in progenies. The pattern of mating type switching in somatic hybrids depends on compatibility of fusion partner. There are several factors related to the mechanism of clamp connection formation and fruiting body development of synkaryons. Of these,the major factor may be associated with self-fertility and mating type switching such as homokaryotic fruiting of wild type P. ostreatus. This review will discuss these aspects.

• The Korean Journal of Mycology
• /
• v.27 no.2 s.89
• /
• pp.112-118
• /
• 1999

Strains of Fusarium oxysporum f. sp. lycopersici isolated from Korea, Japan and U.S.A. were used for electrophoretic karyotype (EK) analysis. Chromosome separations on FastLane agarose gels (FMC BioProducts, Rockland, ME), called pulsed field gel electrophoresis (PFGE), were performed by CHEF-DRII apparatus (Bio-Rad Laboratories, Melville, NY) using TAE as a running buffer. To obtain optimal condition for separation of chromosome sized DNAs, variable running conditions such as field strengths, swithching intervals, and running time were applied in CHEF gel electrophoresis. We were able to resolve 9 to 11 chromosome sized DNAs ranging in size from 0.76 to 6.41 Mb in isolates from Korea and estimate that the total genome size was ranging from 35.29 to 38.92 Mb. Distinct differences in length range and genome size exist among isolates from different countries. Isolates from Japan and U.S.A. were resolved 9 to 11 chromosome sized DNAs ranging in size from 1.24 to 6.85 Mb and estimated that the total genome size was ranging from 35.32 to 43.87 Mb. Isolates from variable provinces in Korea had the same or similar chromosomal polymorphism and showed different chromosomal DNA patterns compared to isolates from the other countries.