• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.10
• /
• pp.1011-1016
• /
• 2008

Jet-A spray and combustion were numerically analyzed in annular type combustor model using KIVA3V. The combustor geometry have 6 dilute holes. Swirl effect and thermal NO were considered in this investigation to analyze mixing and combustion characteristics. Fuel vapor, flame temperature, NO generation were investigated for various spray angle. As increase of spray angle, Jet-A vapor appeared uniformly in primary zone and evaporation rate was increased. Mixing between fuel vapor and ambient gas was enhanced as increase of spray angle. As a result, high temperature region appeared widely and thermal NO generation rate was increased.

• Journal of the Korean Society of Combustion
• /
• v.14 no.4
• /
• pp.41-47
• /
• 2009

An experimental study was performed to confirm the effect of the changing combustor pressure(-30~30 kpa), combustion characteristics were investigated by measuring the local chemiluminescence intensity, the local temperature distribution and emission. In order to investigate combustion ones, the combustor pressure index($P^*$) was controlled in the range of 0.7~1.3 for each equivalence ratio in the present combustion system, where $P^*$ is defined as the ratio of absolute pressure to atmospheric one. The local mean temperature showed the uniform distributions for lower pressure index, which increased with increasing equivalence ratio. The mean $OH^*$ chemiluminescence intensity, showed high level for lower pressure index for ${\Phi}{\get}1.0$ conditions. EINOx decreased with decreasing pressure index for overall equivalence ratio conditions.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.5 no.4
• /
• pp.83-93
• /
• 2001

A swirler with turbulence generator is designed and manufactured for generating many small-scale eddies in the combustor which contribute to enhancing mixing effect between fuel and air. The method results in not only the disadvantage of pressure loss but also the advantage of promoting combustion and reducing NOx. For the purpose of the study, four kinds of swirler with different turbulence generator area (0%, 3%, 7%, and 12% of reducing flow area) are designed to confirm the effect of mixing according the variation in the area of the turbulence generator. The mixing of combustor in the radial direction is significantly improved and the distributions of flames and temperature are well distributed throughout the cross section of a combustor as area of swirl generator is increased.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.24 no.4
• /
• pp.25-32
• /
• 2020

A numerical study on combustion instabilities in a model combustor was conducted with various momentum flux ratios. Five ratios are calculated based on an actual operating condition of rocket engine. As momentum flux ratio increases, the spreading angle on the injector outlet decreases. And, as increase of axial momentum flux, pressure fluctuation decreases inside the combustor. By using dynamic mode decomposition method, the acoustic modes inside the combustor are identified. Combustion stabilities are analyzed by comparing the damping coefficient of the 2^nd longitudinal mode.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.6
• /
• pp.805-810
• /
• 2002

Development of a small gas-turbine combustor for 100㎾ class APU(Auxiliary Power Unit) has been performed. This combustor is a reverse-annular type and has a tangential swiller in the liner head to improve the fuel/air mixing and flame stability. Three main and three pilot fuel injectors of the simplex pressure-swirl type are used. The performance target at the design condition includes a turbine inlet temperature of l170k, a combustion efficiency of 99%, a pattern factor of 30%, and an engine durability of 3000 hours. Under developing the combustor, we conducted the performance test of our first prototype(TS1) with some variants. As a result of the test, the performance targets of the combustor are satisfied except that the pattern factor is about 4% higher than the target value. Therefore, the second prototype(TS2) was redesigned and the performance test was conducted with the critical focus on the pattern factor and the exit mean temperature. We adopted TS2 four variants to check the improvement of the pattern factor. As a result, the pattern factors of several variants were satisfied with the performance target. Finally, the TS2A variant was chosen as a final combustor fur our APU model.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.16 no.4
• /
• pp.57-69
• /
• 2012

The main objective of this study was investigation of natural gas flames in a lean premixed swirl-stabilized dump combustor with an attention focused on the effect of the various fuel-air mixing section geometry on the combustion instability characteristics. The combustor and mixing section length was varied in order to have different acoustic resonance characteristics from 800 to 1800 mm in combustor and 470, 550, 870 mm in mixing section. We observed two dominant instability frequencies in this study. Lower frequencies were associated with a fundamental longitudinal mode of combustor length. Higher frequencies were related to secondary longitudinal mode of coupled with the combustor and mixing section. As a result, combustion instability was strongly affected by acoustic characteristics of combustor and mixing section geometry.

• Journal of the Korean Institute of Gas
• /
• v.26 no.6
• /
• pp.37-44
• /
• 2022

In this study, two low-swirl nozzles with the same SN (Swirl Number) but different mass ratio (m) of the core part and the swirler part were designed to perform an atmospheric pressure combustion test. For each nozzle, a combustion test was conducted according to the adiabatic flame temperature, and the flame structure, emissions, and combustion instability mode were identified. Although the flame structure was significantly different, the CO emission was similar, and the NOx emission was also more related to combustion dynamics than the flame structure. Combustion dynamics and NOx emission were identified while adjusting the convection delay time by changing the position of the fuel injection nozzle. It was confirmed that when the convection delay time is in the region of (3+4n)/4T±1/4T (n=0,1,2,...), the combustion instability is strong, and in the opposite case, the combustion instability is very weak.

• 한국연소학회:학술대회논문집
• /
• 2014.11a
• /
• pp.75-76
• /
• 2014

The present study has numerically investigated the effects of the oxidizer-side nitrogen dilution on the precise structure and NOx formation characteristics of the turbulent syngas nonpremixed flames. Eulerian particle flamelet model was used to predicted the NOx formation characteristics in the turbulent syngas swirling nonpremixed flames. Current numerical simulation was conducted for the syngas gas turbine combustor. Numericla results indicate that as the H2O portion is increased in diluent, the formation of NOx decreased effectively in turbulent syngas swirl nonpremixed flames.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.5
• /
• pp.130-141
• /
• 1996

Numerical study of a confined, swirling, isothermal and spray-combusting flows has been presented. The pressure-velocity coupling in the Eulerian gas-phase equation is handled by the improved PISO algorithm. The droplet dispersion by turbulence is introduced by a Stochastic Separated Flow(SSF) model. The k-$\varepsilon$ turbulence model and the eddy dissipation model are employed to account for turbulence-combustion interaction. The detailed comparison with experimental data has been made for the isothermal jet swirling flows and the nearly monodisperse spray-combusting flow in the swirl combustor.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2001.11a
• /
• pp.50-53
• /
• 2001

Flame propagation during the initial stages of ignition in a non-premixed swirl, having some of characteristics of the primary zone of an aero gas turbine combustor, has been investigated. Nd:YAG laser was adopted as the principal ignition source to allow arbitrary placing of the ignition site i subsequent flame development was monitored using a natural light high speed filming technique for many ignition site at two different swirl ratios and an overall equivalence ratio of 0.9. For ignition offset from the burner centreline, buoyancy force associated with radial pressure gradient produced a strong inward movement of the flame kernel. At the burner exit. flame kernels invariably developed into cylindrical form and a 'radial confinement /axia expansion' (RCAE) process was observed.