• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.609-612
• /
• 2007

The HDD (hard disk drive) using Load/Unload (L/UL) technology includes the benefits which are increased areal density, reduced power consumption and improved shock resistance than those of contact-start-stop (CSS). Dynamic L/UL has been widely used in portable hard disk drive and will become the key technology for developing the small form factor hard disk drive. The main design objectives of the L/UL mechanisms are no slider-disk contact or no media damage even with contact during L/UL, and a smooth and short unloading process. In this paper, we focus on lift-off force, pitch static attitude (PSA), roll static attitude (RSA) and dimple point. The "lift-off" force, defined as the minimum air bearing force, is another very important indicator of unloading performance. A large amplitude of lift-off force increases the ramp force, the unloading time, the slider oscillation and contact-possibility. PSA and RSA are also very important parameters in L/UL system and stability of slider is mainly determined by PSA and RSA. Dimple point by PSA and RSA is also important indicator. Therefore we find the optimal dimple point of SFF HDD suspension for improving the unloading performance.

• Transactions of the Society of Information Storage Systems
• /
• v.8 no.1
• /
• pp.33-38
• /
• 2012

To investigate of load/unload performance, FE (finite element) model of conventional suspension and HAMR suspension were made. The FE models were verified by modal analysis. In the loading simulation, the conventional system could stably load onto the disk without contact. On the other hand, the HAMR suspension which had an optical fiber and prism occurred slider - disk contact. In the unloading process, the conventional system was unloaded without contact. However, in the HAMR suspension, the contact between slider and disk was occurred at the moment that the dimple was separated during unload process. Therefore the load/unload performance of HAMR decrease with high stiffness, it is necessary that stiffness of HAMR suspension should reduced with design parameters of optical fiber and prism.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.467-472
• /
• 2005

Load/Unload(L/UL) technology includes the benefits, that is, increased areal density, reduced power consumption and improved shock resistance contrary to contact start stop(CSS). It has been widely used in portable hard disk drive and will become the key technology for developing the small form factor hard disk drive. The main objectives of L/UL are no slider disk contact or no media damage. For realizing those, we must consider many design parameters in L/UL systems. In this paper, we focus on the effect of the ramp profile. We can find out the lateral velocities in L/UL process through experiments and simulations for force of voice coil motor and friction force on ramp. And then, we will gain the optimal design of ramp slope to maintain the minimum clearance of suspension dimple and slider with FE model. In special, after finding the point at which air bearing breaks and designing the ramp, we will identify the results for improving unload performance.

• Transactions of the Society of Information Storage Systems
• /
• v.5 no.2
• /
• pp.70-75
• /
• 2009

Most hard disk drives uses load/unload technology because of benefits as like an increased areal density, a reduced power consumption and an improved shock resistance. However, ramp tilt induced by ramp manufacture and assembly causes mechanical problems such as unload fail in case of exceeding ramp tolerance. In this paper, we focus on experimental analysis for unloading characteristics affected by ramp tilt. We repeatedly perform load/unload test as 500,000 cycles for original model and ramp tilt model. This paper shows that it is possible to analyze unload characteristics through measuring scratch and wear of suspension lift-tab, ramp, suspension dimple-flexure and disk. We also identify structural relation between suspension lift-tab and ramp through scratch and wear of suspension lift-tab and ramp. As the result of measurement and analysis, we can investigate decrease of unloading performance in ramp tilt model.

• The Plant Pathology Journal
• /
• v.37 no.4
• /
• pp.347-355
• /
• 2021

Ripe rot caused by Botryosphaeria dothidea is one of the serious diseases of postharvest kiwifruit. In order to control ripe rot on Actinidia chinensis cultivar 'Zesy002', several commercial agrofungicides were selected by an antifungal test on an artificial medium. Furthermore, disease suppression by the selected fungicides was evaluated on the kiwifruit by inoculation with a conidial suspension of B. dothidea. On the artificial media containing boscalid + fludioxonil was shown to be the most effective antifungal activity. However, in the bio-test pyraclostrobin + boscalid and iminoctadinetris were the most effective agrochemicals on the fruit. On the other hand, the infection structures of B. dothidea on kiwifruit treated with pyraclostrobin + boscalid were observed with a fluorescent microscope. Most of the fungal conidia had not germinated on the kiwifruit treated with the agrochemicals whereas on the untreated fruit the fungal conidia had mostly germinated. Electron microscopy of the fine structures showed morphological changes to the conidia and branch of hyphae on the kiwifruit pre-treated with pyraclostrobin + boscalid, indicating its suppression effect on fungal growth. Based on this observation, it is suggested that ripe rot by B. dothidea may be suppressed through the inhibition of conidial germination on the kiwifruit treated with the agrochemicals.