• Proceedings of the Korean Geotechical Society Conference
• /
• 2001.03a
• /
• pp.183-190
• /
• 2001

There are complicated and big shear zone which is about several tens meter in the middle of the cutting slope in this study area. And slope stability analysis is very hard because many fault zones are gathered in the shear zone. This study furnish imformations of scrutinized geological survey, numerical stability analysis, reinforcement work analysis and computation of ground mass properties. Then this offer rational slope stability analysis, rock mass decision and counterplan.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.10a
• /
• pp.961-964
• /
• 2016

This paper describes the implementation of AUSV system for Sonar Image acquisition. The system be controlled by FF-PID algorithm for the thrusters using motion sensor and DGPS. As experimental results, the control performance is that the error distance from the destination positions are under 5m in total survey track of 1km, and the image deviation is under 12 pixel from the manned survey method, which the comparison with the total image quality is almost the same as the manned survey one. Thus the AUSV system is a new method of system can be utilized on the limited survey area as the surveyor should not be able to approach on sea surface.

• Journal of Korean Society for Atmospheric Environment
• /
• v.32 no.1
• /
• pp.9-20
• /
• 2016

Ozone has been a problem in big cities. That is secondary air pollutant produced by nitrogen oxide and VOCs in the atmosphere. In order to solve this, the first to be the analysis of the $NO_x$ and VOCs. The main source of nitrogen oxide is the road mobile. Industrial sources in Seoul are particularly low, and mobile traffics on roads are large, so 45% of total $NO_x$ are estimated that road mobile emissions in Seoul. Thus, it is necessary to clarify the relation with the activity of road mobile source and $NO_x$ concentration. In this study, we analyzed the 4 locations with roadside automatic monitoring systems in their center. The V.K.T. calculating areas are set in circles with 50 meter spacing, 50 meter to 500 meter from their center. We assumed the total V.K.T. in the set radius affect the $NO_x$ concentration in the center. We used the hourly $NO_x$ concentrations data for the 4 observation points in July for the interference of the other sources are minimized. We used the intersection traffic survey data of all direction for construction of the V.K.T. data, the mobile activities on the roads. ArcGIS application was used for calculating the length of roads in the set radius. The V.K.T. data are multiplied by segment traffic volume and length of roads. As a result, the $NO_x$ concentration can be expressed as linear function formula for V.K.T. with high predictive power. Moreover we separated background concentration and concentrations due to road mobile source. These results can be used for forecasting the effect of traffic demand management plan.

• Journal of the Society of Disaster Information
• /
• v.17 no.1
• /
• pp.53-59
• /
• 2021

Purpose & Method: The purpose of this study is the theoretical study on the durability standard of ground structures monitoring sensors. A survey on the durability criteria for construction monitoring sensors of domestic construction companies and the income tax implementation regulations, the standard years of contents such as buildings and the standards of the Public Procurement Service for construction monitoring and construction machinery were analyzed. Result: The durability criterion such as the inclination meter and the strain gauge, which are purchased from the Public Procurement Service prior to installation on the ground structure, is 8 to 10 years. Conclusion: The actual durability analysis by comparing the reliability of various monitoring sensors installed in dams at home and abroad, As a result of comprehensive study on the loss and damage rate of the maintenance monitoring sensor installed in the tunnel, the proper durability period of the built-in type monitoring sensor such as domestic pore pressure meter and earth pressure meter installed in the structure or the ground is 5 to 8 years it seems reasonable.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.33 no.4
• /
• pp.439-446
• /
• 2023

Objectives: The aims of this study are to investigate how X-rays are emitted to surrounding parts during the ion implantation process, to analyze these emissions in relation to the properties of the ion implanter equipment, and to estimate the resulting exposure dose. Eight ion implanters equipped with high-voltage electrical systems were selected for this study. Methods: We monitored X-ray emissions at three locations outside of the ion implanters: the accelerator equipped with a high-voltage energy generator, the impurity ion source, and the beam line. We used a Personal Portable Dose Rate and Survey Meter to monitor real-time X-ray levels. The SX-2R probe, an X-ray Features probe designed for use with the Radiagem^TM meter, was also utilized to monitor lower ranges of X-ray emissions. The counts per second (CPS) measured by the meter were estimated and then converted to a radiation dose (𝜇Sv/hr) based on a validated calibration graph between CPS and μGy/hr. Results: X-rays from seven ion implanters were consistently detected in high-voltage accelerator gaps, regardless of their proximity. X-rays specifically emanated from three ion implanters situated in the ion box gap and were also found in the beam lines of two ion implanters. The intensity of these X-rays did not show a clear pattern relative to the devices' age and electric properties, and notably, it decreased as the distance from the device increased. Conclusions: In conclusion, every gap, in which three components of the ion implanter devices were divided, was found to be insufficiently shielded against X-ray emissions, even though the exposure levels were not estimated to be higher than the threshold.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.37 no.3
• /
• pp.249-254
• /
• 2004

The hydro-acoustic method is widely used for estimating biomass and distribution of fisheries resources along the coast and in the ocean. High costs and time are necessary to construct systems for this method and to initially educate specialists. It has been used in fisheries of advanced nations like Japan and Norway, because it is more efficient than other methods. In order to research the behavior of fish around an artificial reef using an echo sounder, volume backscattering strength (SV) and fish per cubic meter (FPCM) of darkbanded rockfish around the model artificial reef in a water tank were measured. Moreover, behavior of fish was observed in an adjacent artificial reef, which was constructed at Tongyeong marine ranching area. Following that, an acoustics survey was conducted at Mirukdo around the Tongyeong marine ranching area, in order to understand the spatial distribution and strength of fisheries resources. Very high patches of fish were found in a wide area around the artificial reef. It is thought that an approaching fish school around the artificial reef can be measured accurately by using an echo sounder of high resolution. Moreover, use of other monitoring methods like of diving or ROV simultaneous with an echo sounder is required in order to grasp the species and ecology of fish inhabiting the area around the artificial reef.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.05a
• /
• pp.205-208
• /
• 2002

When establishing the submarine optical fiber table between international and domestic, marine survey in advance it grasps the submarine geological features which is accurate and a depth of water condition. And the route which is safe for selecting and submarine optical fiber cable laying it is a work which secures an ease one location. If also, the PLGR the submarine of optical fiber table root the sea contamination material (rope, wire and net) it removes in advance and if the submarine of the optical fiber cable ease it does to arrive safely. And it is a work the Plough and ROV laying work hour laying work efficiency improvement and laying equipment it will be able to protect. So, This paper presents the monitoring system of ship information management and operation for marine survey and PLGR work in submarine optical fiber table construction enterprise. In order to achieve these purpose, overall serial multi-port communication modulo of configuration, realtime processing for management and operation of receiving data, realtime graph and a printout are described.

• Analytical Science and Technology
• /
• v.16 no.1
• /
• pp.12-24
• /
• 2003

For the design and set-up of neutron induced prompt ${\gamma}$-ray spectroscopy system using $^{252}Cf$ neutron source, the effects of shielding and moderator materials have been examined. The $^{252}Cf$ source being used for TLD badge calibration in Korea Atomic Energy Research Institute was utilized for this preliminary experiment. The ${\gamma}$-ray background and prompt ${\gamma}$-ray spectrum of the sample containing Cl were measured using HPGe (GMX 60% relative efficiency) located at the inside of the system connected to notebook PC at the outside of the system (about 20 meter distance). The background activities of neutron and ${\gamma}$-rays were measured with neutron survey meter as well as ${\gamma}$-ray survey meters, respectively and the system was designed to minimize the activities. Prompt ${\gamma}$-ray spectrum was measured using ${\gamma}$-${\gamma}$ coincident system for reduce the background and the continuum spectrum. The optimum system was designed and set up using the experimental data obtained.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.26 no.4
• /
• pp.246-254
• /
• 2006

A computation program has been developed for automatic data processing in the calibration process of gamma survey meter. The automatic processing program has been developed based on Visual Basic. The program has been coded according to steps of calibration procedure. The OLE(object linking an embedding) Excel automation method fur automatic data processing is used in this program, which is a kind of programming technique for the Excel control. The performance test on the basis of reference data has been carried out by using the developed program. In the results of performance test, the values of calibration factors and uncertainties by the developed program were equal to those obtained from the reference data. In addition, It was revealed that the efficiency and precision of working are significantly increased by using the developed program.

• Proceedings of the KSRS Conference
• /
• 2007.10a
• /
• pp.591-593
• /
• 2007

This paper is to cluster the AMR (Automatic Meter Reading) data. The load survey system has been applied to record the power consumption of sampling the contract assortment in KEPRI AMR. The effect of the contract assortment change to the customer power consumption is determined by executing the clustering on the load survey results. We can supply the power to customer according to usage to the analysis cluster. The Korea a class of the electricity supply type is less than other country. Because of the Korea electricity markets exists one electricity provider. Need to further divide of electricity supply type for more efficient supply. We are found pattern that is different from supplied type to customer. Out experiment use the Clementine which data mining tools.