• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.308-309
• /
• 2016

Reducing surface recombination is a critical factor for high efficiency silicon solar cells. The passivation process is for reducing dangling bonds which are carrier. Tunnel oxide layer is one of main issues to achieve a good passivation between silicon wafer and emitter layer. Many research use wet-chemical oxidation or thermally grown which the highest conversion efficiencies have been reported so far. In this study, we deposit ultra-thin tunnel oxide layer by PECVD (Plasma Enhanced Chemical Vapor Deposition) using $N_2O$ plasma. Both side deposit tunnel oxide layer in different RF-power and phosphorus doped a-Si:H layer. After deposit, samples are annealed at $850^{\circ}C$ for 1 hour in $N_2$ gas atmosphere. After annealing, samples are measured lifetime and implied Voc (iVoc) by QSSPC (Quasi-Steady-State Photo Conductance). After measure, samples are annealed at $400^{\circ}C$ for 30 minute in $Ar/H_2$ gas atmosphere and then measure again lifetime and implied VOC. The lifetime is increase after all process also implied VOC. The highest results are lifetime $762{\mu}s$, implied Voc 733 mV at RF-power 200 W. The results of C-V measurement shows that Dit is increase when RF-power increase. Using this optimized tunnel oxide layer is attributed to increase iVoc. As a consequence, the cell efficiency is increased such as tunnel mechanism based solar cell application.

• Geomechanics and Engineering
• /
• v.7 no.5
• /
• pp.495-524
• /
• 2014

To investigate the soil-pile interactive performance under lateral loads, a set of laboratory model tests was conducted on remoulded test bed of soft clay and medium dense sand. Then, a simplified boundary element analysis had been carried out assuming floating pile. In case of soft clay, it has been observed that lateral loads on piles can initiate the formation of a gap, soil heave and the tension crack in the vicinity of the soil surface and the interface, whereas in medium dense sand, a semi-elliptical depression zone can develop. Comparison of test and boundary element results indicates the accuracy of the solution developed. However, in the boundary element analysis, the possible shear stresses likely to be developed at the interface are ignored in order to simplify the existing complex equations. Moreover, it is unable to capture the influence of base restraint in case of a socketed pile. To bridge up this gap and to study the influence of the initial stress state and interface parameters, a field based case-study of laterally-loaded pile in layered soil with socketed tip is explored and modelled using the finite element method. The results of the model have been verified against known field measurements from a case-study. Parametric studies have been conducted to investigate the influence of the coefficient of lateral earth pressure and the interface strength reduction factor on the results of the model.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.6
• /
• pp.123-133
• /
• 2001

Since most of soil slopes are in an unsaturated state, it is necessary to consider the unsaturated characteristics of soil slopes, in order to obtain more reasonable results. Therefore in this study we supplemented a slope stability analysis program to consider them, based on the concept of limit equilibrium. We also applied an optimization technique to search for a failure surface. Besides, we carried out experiments to obtain the unsaturated soil properties required in the analysis with weathered granite soils. We formulated a nonlinear apparent cohesion relationship with the matrix suction to be able to apply the unsaturated shear strength characteristics to the stability analysis. In addition, we intended to obtain more accurate soil water characteristic curves(SWCC) by measuring the change in volume of the specimen in the SWCC tests. As a result, we could appropriately assess the change of the safety factor according to the rainfall intensity and duration, by considering the variation of suction, permeability, and shear strength caused by the infiltration of rainfall into slopes.

• Journal of the Korean Vacuum Society
• /
• v.2 no.4
• /
• pp.439-454
• /
• 1993

The phase sequence of codeposited Co-Si alloy and Co/si multilayer thin film was investigated by differential scanning calormetry(DSC) and X-ray diffraction (XRD) analysis, The phase sequence in codeposition and codeposited amorphous Co-Si alloy thin film were CoSilongrightarrow Co2Si and those in Co/Si multilayer thin film were CoSilongrightarrowCo2Silongrightarrow and CoSilongrightarrowCo2Si longrightarrowCoSilongrightarrowCoSi2 with the atomic concentration ration of Co to Si layer being 2:1 and 1:2 respectively. The observed phase sequence was analyzed by the effectvie heat of formatin . The phase determining factor (PDF) considering structural facotr in addition to the effectvie heat of formation was used to explain the difference in the first crystalline phase between codeposition, codeposited amorphous Co-Si alloy thin film and Co/Si multilayer thin film. The crystallinity of Co-silicide deposited by multitarget bias cosputter deposition (MBCD) wasinvestigated as a funcion of deposition temperature and substrate bias voltage by transmission electron microscopy (TEM) and epitaxial CoSi2 layer was grown at $200^{\circ}C$ . Parameters, Ear, $\alpha$(As), were calculate dto quantitatively explain the low temperature epitaxial grpwth of CoSi2 layer. The phase sequence and crystallinity had a stronger dependence on the substrate bias voltage than on the deposition temperature due to the collisional daxcade mixing, in-situ cleannin g, and increase in the number of nucleation sites by ion bombardment of growing surface.

• Microbiology and Biotechnology Letters
• /
• v.7 no.3
• /
• pp.165-173
• /
• 1979

Recovery component for cell division in UV-irradiated E. coli B was detected with use of the cell extract of E. coli B/r which is a resistant mutant of E. coli B against UV-irradiation. The active substance was non-dialyzable and increased the activity by adding B-NAD remarkably. One more factor for increasing or promoting the restoration recognized was magnesium. Magnesium was effective to stabilze the substance in procedure of isolation. Two active substances were obtained from sucrose gradient centrifugation. One of them was recovred from the botton area and the other from top area just below below surface. the former was not stabilized by magnesium, while the latter stabilized the activity by it remarkably. The former which did not require magnesium was insensitive to protease and the latter which required magnesium was sensitive to it. Both were insensitive to RNase and DNase. Recovery ratio was doubled by using nitrogen gas than aeration in purification process. DNA-ligase less mutant was revealed same activity on it's recovery ratio with the parent strain of E. coli K-12. The active substance stimulating the filament cell may exist as a complex which is inactivated easily in the dissociated state ana requrie B-NAD or magnesium.

• Ocean and Polar Research
• /
• v.32 no.2
• /
• pp.123-135
• /
• 2010

Around Tongyeong coasts which located in southern coast of Korea composed to the complex coastal line and scattered by small islands. It also has been distributed to a complicated bathymetric structure by several types of channels. This study carried to analyze the spatial characteristics of macrobenthic community and benthic environmental variance on sub-tidal area based on multivariate statistics tools. Sediment composition varied from muddy sand to mud, and along the channels, it composed to a heterogeneous bottoms mixed by shell fragment, cobbles and mud. Organic contents on the surface sediment varied 1.1-3.9%. Total of 272 species, $33,349\;ind./m^2$ of macrobenthos identified in all of sample area. Polychaetes also prevailed among the specimen. L. longifolia, P. pinnata dominated based on density. Considering on the biomass, echinoderm S. lacunosa, A. tricoides listed. Closer to the coastal area, the density and diversity were higher. Community structure based on cluster analysis was discriminated into three groups. Each group was also characterized by geographical state such as depth, sediment composition. In addition, when applied to the bathymetric data, the channel, which composed to the mixed sediment, made a role of limited factor which characterized to benthic community. Because the specimen around the channel have been affected on the diverse sediment mixture. Most of benthic studies in the southern coast of Korea focused to the condition of benthic organic pollution spatially, because along the coast, it also developed a aquaculture ground and industrial complex. But, as results, most of the area, it turn out the less polluted areas nevertheless similar environment situation. It supposed that benthic community affect to the bottom sediment composition by physical characteristics.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.5
• /
• pp.88-95
• /
• 2015

The thickness of adsorbed molecular layers is the most critical factor in studying thin-film lubrication, and it is the most essential parameter that distinguishes thin-film from thick-film lubrication analysis. The thin film between the shaft and bearing surface within a very narrow gap was considered. The general Reynolds equation has been derived for calculating thin-film lubrication parameters affecting the performance of the circular journal bearing. Investigation of the load-carrying capacity and pressure distribution for the journal bearing considering the adsorbed layer thickness has been carried out. A Reynolds equation appropriate for the journal bearing is used in this paper for the analysis, and it is discussed using the finite difference method of the central difference scheme. The parameters, such as eccentricity and attitude angle, are used for discussing the load-carrying capacity of the journal bearing. The results reported in this paper should be applied to analysis of the journal bearing with different lubrication factors. The steady-state analysis of the journal bearing is conducted using the Reynolds model under thin-film lubrication conditions. For a journal bearing, several parameters, such as a pressure, load capacity, and pressure components of the bearing can be obtained, and these results can be stored in a sequential data file for later analysis. Finally, their distribution can be displayed and analyzed easily by using the MATLAB GUI technique. The load-carrying capability of the journal bearing is observed for the specified operating conditions. This work could be helpful for the understanding and research of the mechanism of thin-film lubrication.

• Korean Journal of Ecology and Environment
• /
• v.38 no.3 s.113
• /
• pp.382-392
• /
• 2005

Data were collected in Lake Daecheong from March 1997 to October 2002 and used to understand an annual change of water environmental factors and trophic states. The surface water temperature was ranged from $3.2^{\circ}C$ to $33.1^{\circ}C$ In the middle of February, water temperature was the lowest. Turbidity was ranged from 0.1 to 203.5 NTU, but the values of above 30 NTU were only measured at site 1. The total mean values of COD and Chl a were $3.6{\pm}1.4\;mg\;O_2\;L^{-1}$, $9.3{\pm}12.8\;{\mu}g\;L^{-1}$respectively. The concentrations of TP and TN were ranged from 0.14 to 5.09 mg N $L^{-1}$, 1 to $247\;{\mu}g\;P\;L^{-1}$ respectively. The total mean value of TN/TP ratio was $98.7{\pm}56.2$. The trophic states were ranged from mesotrophic to eutrophic in Lake Daecheong.

• Journal of the Korean Ceramic Society
• /
• v.45 no.12
• /
• pp.827-831
• /
• 2008

Spark plasma sintering (SPS) of AlN ceramics were carried out with ${Y_2}{O_3}$ as sintering additive at a sintering temperature $1,550{\sim}1,700^{\circ}C$. The effect of ${Y_2}{O_3}$ addition on sintering behavior and thermal conductivity of AlN ceramics was studied. ${Y_2}{O_3}$ added AlN showed higher densification rate than pure AlN noticeably, but the formation of yttrium aluminates phases by the solid-state reaction of ${Y_2}{O_3}$ and ${Al_2}{O_3}$ existed on AlN surface could delay the densification during the sintering process. The thermal conductivity of AlN specimens was promoted by the addition of ${Y_2}{O_3}$ up to 3 wt% in spite of the formation of YAG secondary phase in AlN grain boundaries because ${Y_2}{O_3}$ addition could reduced the oxygen contents in AlN lattice which is primary factor of thermal conductivity. However, the thermal conductivity rather decreased over 3 wt% addition because an immoderate formation of YAG phases in grain boundary could decrease thermal conductivity by a phonon scattering surpassing the contribution of ${Y_2}{O_3}$ addition.

• Wind and Structures
• /
• v.28 no.5
• /
• pp.299-313
• /
• 2019

In order to examine the effects of different wind deflectors on the wind load distribution characteristics of extra-large cooling towers, a comparative study of the distribution characteristics of wind pressures on the surface of three large cooling towers with typical wind deflectors and one tower without wind deflector was conducted using wind tunnel tests. These characteristics include aerodynamic parameters such as mean wind pressures, fluctuating wind pressures, peak factors, correlation coefficients, extreme wind pressures, drag coefficients and vorticity distribution. Then distribution regularities of different wind deflectors on global and local wind pressure of extra-large cooling towers was extracted, and finally the fitting formula of extreme wind pressure of the cooling towers with different wind deflectors was provided. The results showed that the large eddy simulation (LES) method used in this article could be used to accurately simulate wind loads of such extra-large cooling towers. The three typical wind deflectors could effectively reduce the average wind pressure of the negative pressure extreme regions in the central part of the tower, and were also effective in reducing the root of the variance of the fluctuating wind pressure in the upper-middle part of the windward side of the tower, with the curved air deflector showing particularly. All the different wind deflectors effectively reduced the wind pressure extremes of the middle and lower regions of the windward side of the tower and of the negative pressure extremes region, with the best effect occurring in the curved wind deflector. After the wind deflectors were installed the drag coefficient values of each layer of the middle and lower parts of the tower were significantly higher than that without wind deflector, but the effect on the drag coefficients of layers above the throat was weak. The peak factors for the windward side, the side and leeward side of the extra-large cooling towers with different wind deflectors were set as 3.29, 3.41 and 3.50, respectively.