• Journal of Welding and Joining
• /
• v.17 no.6
• /
• pp.70-77
• /
• 1999

Surface depression in the arc welding is calculated numerically to analyze its influence on pool convection and oscillation. The magnitude of surface depression due to arc pressure on the stationary GTA pool surface is relatively small, and fluctuations of the surface and velocity are caused mainly by arc pressure. The inward flow on the surface due to the electromagnetic force and positive surface tension gradient acts to decrease surface depression. Surface depression appears to have minor effects on average flow velocity and thus pool geometry. Pool oscillation occurs due to surface vibration, and oscillation frequencies are affected mainly by the surface tension and pool width. The input parameters such as arc pressure and current have negligible effects on the oscillation frequency, and the surface tension gradient has limited effects. Since the oscillation frequency varies slightly according to penetration, pool oscillation for the partial penetration weld pool is applicable to monitor the pool width.

• Journal of Fashion Business
• /
• v.20 no.1
• /
• pp.69-81
• /
• 2016

In this study investigated the effect of emotional labor, emotional exhaustion, and depression on the job-related attitudes. Sample subjects used in this study were salespeople of a fashion shop in Jeollabukdo and Jeollanamdo. Questionnaire data from 160 fashion shop salespeople were analyzed through a reliability analysis, factor analysis, and multiple regression analysis. The results of the study were as follows. First, emotional labor of salespeople was divided into 2 factors, surface acting and deep acting. Second, emotional labor had a significant influence on the emotional exhaustion and depression. Third, the surface acting of emotional labor had a positive influence on the emotional exhaustion and depression; whereas, the deep acting of emotional labor had a negative influence on the emotional exhaustion and depression. Fourth, the surface acting of emotional labor, emotional exhaustion, and depression had a negative influence on job involvement; in addition, the deep acting of emotional labor had a positive influence on job involvement. Fifth, the surface acting of emotional labor, emotional exhaustion, and depression had a positive influence on turnover intention; in addition, the deep acting of emotional labor had a negative influence on turnover intention.

• Journal of Periodontal and Implant Science
• /
• v.36 no.3
• /
• pp.705-716
• /
• 2006

The present study was performed to evaluate the effect of tetracycline-HCl on the change of implant surface microstructure according to application time. Implant with pure titanium machined surface, GBA surface and RBM surface were utilized. Implant surface was rubbed with 50mg/ml tetracycline-HCl solution for ${\frac{1}{2}}$min. 1min. $1{\frac{1}{2}}$min. 2min. and $2{\frac{1}{2}}$min. respectively in the test group. Then, specimens were processed for scanning electron microscopic observation. The results of this study were as follow. 1. Both test and control group showed a few shallow grooves and ridges in pure titanium machined surface implants. There were not significant differences between two group. 2. In GBA surfaces, control group exhibit many porous depression, and each depression were divided by strict border. Experimental group applied with tetracycline-HCl for 2min. were similar with control group. But when applied for $2{\frac{1}{2}}$min. surface alteration and border breakdown started, resulting enlargement of the porous depression. 3. In REM surface, control group exhibit rough, uneven surface with crater-like depression can be found. The surface alteration started when tetracycline-HCl was applied for 30sec. resulting breakdown of the crater-like depression. Depression became larger as applying time increased.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.7
• /
• pp.3030-3038
• /
• 2011

This study was conducted as descriptive research to examine the relations among beauty business workers' professional identity, emotional labor and depression, to analyze factors that influence their depression, and to provide basic information necessary to develop interventions for beauty business workers' depression. The subjects of this study were 158 beauty business workers sampled from 25 beauty shops in Seoul. Data were collected using a structured questionnaire during the period from April 12 to May 13, 2011. From the collected data were obtained real numbers, percentages, and the means and standard deviations of professional identity, emotional labor and depression using the SPSS 16.0 Program. In addition, multiple regression analysis was performed to determine the correlations among the variables and to identify factors influencing the beauty business workers' depression. In the results of multiple regression analysis on factors that influence the subjects' depression, factors found to explain their depression were autonomy among the sub factors of professional identity, and the diversity of emotional expressions and surface acting among the sub factors of emotional labor, and these factors explained 23.6% of their depression. The subjects' professional identity was in a positive correlation with the frequency of emotional expressions and deep acting among the sub factors of emotional labor, and in a negative correlation with surface acting and depression. The Frequency of emotional expression and the diversity of emotional expressions which the sub factors of emotional labor were in a negative correlation with depression and in a positive correlation with surface acting and depression. In order to relieve beauty business workers from their depression based on these results, there should be education or programs for establishing beauty business workers' professional identity and program for increasing of emotional expressions and decreasing of surface acting.

• Journal of Korean Society of Forest Science
• /
• v.107 no.1
• /
• pp.108-111
• /
• 2018

Increasing soil surface roughness can be effective in enhancing infiltration of rainfall and depression storage capacity of forest soil and reducing surface run-off. In this study, a forest slope with hemispherical depressions shows greater infiltration of water, whereas depression storage capacity is higher in soil with depressions perpendicular to a water flow pathway. Soil pitting or forming surface depressions can be used as a countermeasure after forest fires and a practical way to reduce drought stress of forest soil.

• Korean Journal of Materials Research
• /
• v.13 no.2
• /
• pp.74-80
• /
• 2003

The effects of risering design and alloying element on the formation of defects such as external depression, primary and secondary shrinkage cavities in ductile cast iron were investigated. Two types of risering design for the cylindrically step-wise specimen, No. 1(progressive solidification) and No. 2(directional solidification) risering designs, were prepared and six different alloy compositions were casted. In the No. 1 risering design, external depression or primary shrinkage cavities due to liquid contraction were observed in all the specimens from SG 10 to SG 60. The defects caused by liquid contraction seemed to be more affected by risering design than alloying elements. The secondary shrinkage cavities were also observed in all the specimens but a swollen surface was not observed in all the castings. The primary shrinkage cavities were located right under the top surface or connected to the top surface, and were characterized by smooth surfaces. On the other hand, the secondary shrinkage cavities were positioned in the thermal center of the specimen steps 3 and 4, and characterized by rough surfaces. In the No. 2 risering design, no external depression or primary shrinkage cavities due to liquid contraction were observed in all the specimens from SG 10 to SG 60. However, the secondary shrinkage cavities were formed in the thermal center of specimens SG 40, 50 and 60. Like the No. 1 risering design, a swollen surface was not observed in all the castings.

• Restorative Dentistry and Endodontics
• /
• v.26 no.4
• /
• pp.316-325
• /
• 2001

The purpose of this study was to evaluate the effect of adhesive curing timing on the direction of polymerization shrinkage of light-curing composite resin. In this study, the curing times of adhesive and composite resin were measured by differential scanning calorimeter(DSC). 28 extracted human molars were embedded in clear resin and box-type cavities were prepared. Based on DSC data, the experimental teeth were divided into 4 groups. Group 1: no bond; Group 2: late curing; Group 3: Intermediate curing; Group 4: Early curing. After treating with adhesive, the buccal cavities were filled with Z-100 hybrid composite resin and the lingual ones were filled with AEliteflo flowable composite resin. The depressions at the surface were measured by surface profilometer, then the specimens were embedded in clear resin and sectioned. Impressions were obtained and used to get epoxy resin replicas. The epoxy replicas were gold-coated and observed under SEM. Average Maximum Gap(AMG), Gap Proportion(GP), Average Marginal Index(AMI) were used to compare the shrinkage gap of each group. The results were statistically analyzed using the Kruskal-Wallis One Way ANOVA, Student-Newman-Keuls method. The results of this study were as follows. 1. Average Maximum Gap, Gap Proportion, Average Marginal Index and depression at the surface or Z-100 hybride composite resin were smaller than those of AEliteflo flowable composite resin(P<0.05). 2. When the bonding between composite resin and tooth structure was strong, the shrinkage gap was small, and depression at the surface was deep(P<0.05). 3. In the well-bonded group, light-curing composite resin shrank toward bonded cavity wall, not toward light source. The result suggested that the direction of polymerization shrinkage was affected by the quality of bonding in the dentin-resin interface. The strong was the bonding between composite resin and tooth structure, the smaller was the gap and the deeper was the depression at the surface. Then the flow to compensate the polymerization shrinkage proceeded from surface to bonded cavity wall.

• Korean Journal of Materials Research
• /
• v.13 no.5
• /
• pp.297-302
• /
• 2003

The effects of risering design and alloying element on the formation of defects such as external depression, primary and secondary shrinkage cavity in gray cast iron were investigated. Two types of risering design for the cylindrically step-wise specimen, No. 1(progressive solidification) and No. 2(directional solidification) risering designs, were prepared and five different alloy compositions were casted. In the No. 1 risering design, external depression or primary shrinkage cavity due to liquid contraction was observed in all the specimens from ISO 150 to ISO 350. The primary shrinkage cavity was located right under the top surface or connected to the top surface, and was characterized by smooth surface. Its size increased with an increase in ISO number. However, neither secondary shrinkage cavity nor swollen surface was observed in all the castings. In the No.2 risering design, neither primary shrinkage cavity nor secondary shrinkage cavity was observed in all the specimens due to proper risering design. A swollen surface was also not observed in all the castings with the application of pep-set mold.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1996.11a
• /
• pp.27-41
• /
• 1996

In this study the heat transfer and fluid flow of the molten pool in stationary gas tungsten arc welding using argon shielding gas were investigated. Transporting phenomena from the welding arc to the base material surface, such as current density, heat flux, arc pressure and shear stress acting on the weld pool surface, were taken from the simulation results of the corresponding welding arc. Various driving forces for the weld pool convection were considered, self-induced electromagnetic, surface tension, buoyancy, and impinging plasma arc forces. Furthermore, the effect of surface depression due to the arc pressure acting on the molten pool surface was considered. Because fusion boundary has a curved and unknown shape during welding, a boundary-fitted coordinate system was adopted to precisely describe the boundary for the momentum equation. The numerical model was applied to AISI 304 stainless steel and compared with the experimental results.

• Geomechanics and Engineering
• /
• v.15 no.3
• /
• pp.851-859
• /
• 2018

There are two primary causes of the ground movement due to tunnelling in urban areas; firstly the lost ground and secondly the groundwater depression during construction. The groundwater depression was usually not considered as a cause of settlement in previous research works. The main purpose of this study is to analyze the combined effect of these two phenomena on the transverse settlement trough. Centrifuge model tests and numerical analysis were primarily selected as the methodology. The characteristics of settlement trough were analyzed by performing centrifuge model tests where acceleration reached up to 80g condition. Two different types of tunnel models of 180 mm diameter were prepared in order to match the prototype of a large tunnel of 14.4 m diameter. A volume loss model was made to simulate the excavation procedure at different volume loss and a drainage tunnel model was made to simulate the reduction in pore pressure distribution. Numerical analysis was performed using FLAC 2D program in order to analyze the effects of various groundwater depression values on the settlement trough. Unconfined fluid flow condition was selected to develop the phreatic surface and groundwater level on the surface. The settlement troughs obtained in the results were investigated according to the combined effect of excavation and groundwater depression. Subsequently, a new curve is suggested to consider elastic settlement in the modified Gaussian curve. The results show that the effects of groundwater depression are considerable as the settlement trough gets deeper and wider compared to the trough obtained only due to excavation. The relationships of maximum settlement and infection point with the reduced pore pressure at tunnel centerline are also suggested.