• Journal of the Korean Chemical Society
• /
• v.56 no.4
• /
• pp.401-405
• /
• 2012

Corrosion inhibition efficiencies of holy basil on Al in HCl solution were studied by weight loss and thermometric methods in presence and in absence of stem extract of three different varieties of holy basil viz. ocimum basilicum ($E_B$), ocimum canum ($E_C$) and ocimum sanctum ($E_S$). Inhibition efficiency increases with the increasing concentration of stem extract and decreases with increases in acid strength. Results show that all varieties under study are good corrosion inhibitors, among which, $E_B$ is most effective. Maximum inhibition efficiency was found 97.09% in 0.5N HCl solution with 0.6% stem extract. The Langmuir adsorption isotherm indicates that surface coverage also increases with increasing in the concentration of extract of stem in HCl solution.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.11a
• /
• pp.344-345
• /
• 2015

Various concentration of copper was dopped in Fe-35%Ni thin sheet by electroforming and their electromagnetic, surface properties were determined. Microstructure observation by scanning electron microscopy revealed that the thin sheet had columnar grains with about 150 nm long. Phase analysis by X-ray diffractometry revealed that the alloy thin sheets were fine crystalline. The average surface roughnesses measured by atomic force microscopy (AFM) were about 14.38 nm. Nano hardnesses determined by tribo-nano indenter were 4.13 GPa. The surface resistances were 2.28 ohm/sq. The maximum magnetization, residual magnetization and coercive force depended on the copper concentration.

• Textile Coloration and Finishing
• /
• v.13 no.1
• /
• pp.18-22
• /
• 2001

Effects of cationic surfactants old the wetting behavior of the DMDHEU treated cotton fibers were investigated using a technique based on the Wilhelmy principle. The results indicated that Interactions between the fiber and water ill the interface make contributions to wettability of the cotton fiber surface because of reorientation of polar groups at the interface. The effects of types and concentration of cationic surfactant on the wettability of both control and durable press(DP) finished cotton fiber are discussed. Below and near the critical micelle concentration(cmc), the adsorption of hexadecyltrimethylammoniumbromide(HTAB) on the control fiber makes the fiber surface more hydrophobic. Near and above the cmc of octadecyltrimethylammouniumbromide(OTAB) , the decrease in advancing contact angles indicates that the control cotton surface became hydrophilic. By the adsorption of both HTAB and OTAB onto the fiber surface, the hydrophobicity of the DP finished fiber surface became mere hydrophilic.

• Korean Journal of Materials Research
• /
• v.22 no.2
• /
• pp.66-70
• /
• 2012

Ti-Ni alloys are widely used in numerous biomedical applications (e.g., orthodontics, cardiovascular science, orthopaedics) due to their distinctive thermomechanical and mechanical properties, such as the shape memory effect, superelasticity and low elastic modulus. In order to increase the biocompatibility of Ti-Ni alloys, many surface modification techniques, such as the sol-gel technique, plasma immersion ion implantation (PIII), laser surface melting, plasma spraying, and chemical vapor deposition, have been employed. In this study, a Ti-49.5Ni (at%) alloy was electrochemically etched in 1M $H_2SO_4$+ X (1.5, 2.0, 2.5) wt% HF electrolytes to modify the surface morphology. The morphology, element distribution, crystal structure, roughness and energy of the surface were investigated by scanning electron microscopy (SEM), energy-dispersive Xray spectrometry (EDS), X-ray diffractometry (XRD), atomic force microscopy (AFM) and contact angle analysis. Micro-sized pores were formed on the Ti-49.5Ni (at%) alloy surface by electrochemical etching with 1M $H_2SO_4$+ X (1.5, 2.0, 2.5) wt% HF. The volume fractions of the pores were increased by increasing the concentration of the HF electrolytes. Depending on the HF concentration, different pore sizes, heights, surface roughness levels, and surface energy levels were obtained. To investigate the osteoblast adhesion of the electrochemically etched Ti-49.5Ni (at%) alloy, a MTT test was performed. The degree of osteoblast adhesion was increased at a high concentration of HF-treated surface structures.

• Journal of Environmental Health Sciences
• /
• v.38 no.6
• /
• pp.568-574
• /
• 2012

Objectives: The purpose of this experiment is to understand the phosphorus removal ratio effects of iron plates per unit of surface area through the iron electrolysis system, which consists of an anoxic basin, aerobic basin, and iron precipitation apparatus. Methods: Iron electrolysis, which uses an iron precipitation reactor in anoxic and oxic basins, consisted of iron plates with total areas of 400 $cm^2$, 300 $cm^2$ and 200 $cm^2$ respectively. The FNR process was operated with a hydraulic retention time and a sludge retention time of 12 hours and three days, respectively. Wastewater used in the experiments was prepared by dissolving $KH_2PO_4$ in influent water. Results: The iron plates 400 $cm^2$ (16.6 $mA/cm^2$), 300 $cm^2$ (13.3 $mA/cm^2$) and 200 $cm^2$ (7.3 $mA/cm^2$) in surface area in the phosphorus reactor had respective phosphorus of 2.4 mg/l, 2.7 mg/l and 3.2 mg/l in the effluent and phosphorus removal respective efficiencies of 90.3%, 89.1% and 87.1%. The effluent in the reactor, where the iron plate was not used, had relatively very low phosphorus removal efficiency showing phosphorus concentration of 15.3 mg/l and a phosphorus removal efficiency about 38.3%. Phosphorus removal per ferrous was 0.472 mgP/mgFe in the iron electrolysis system where the surface area of iron was low. Phosphorus pollution load per active surface area and the phosphorus removal efficiency had an interrelation of RE = -0.27LS + 89.0 (r = 0.85). Conclusion: With larger iron plate surface area, the elution of iron concentration and phosphorus removal efficiency was higher. The removal efficiency of phosphorus has decreased by increasing the initial phosphate concentration in the iron electrodes. This shows a tendency of decreasing phosphorus removal efficiency because of decreasing of iron deposition as the phosphorus pollution load per active surface area increases.

• Korean Journal of Food Science and Technology
• /
• v.25 no.5
• /
• pp.571-575
• /
• 1993

Effect of surface hydrophobicity of soybean peptides on serum cholesterol in rats was investigated. Soybean protein(ISP), casein(CNP), and their peptic hydrolyzates fractionated by acid precipitations (SHT, SH8, SH6, SH4, CHT, CH6, CH5, CH4) were fed to rats and the concentration of serum cholesterol and the fecal steroid excretion were measured. And surface hydrophobicities of the peptide fractions were measured by determining by the ANS flourescence intensity and SDS binding capacity. It was found that the higher the surface hydrophobicity of peptides was, the more the fecal steroids excreted(r=0.801) and the lower the concentration of serum cholesterol became(r=-0.868). However, there was no relationship between SDS surface hydrophobicity and fecal steroids or serum cholesterol. ANS surface hydrophobicity of soybean protein was increased by enzymatic hydrolysis. These results suggest that high surface hydrophobicity of peptides formed during digestion is responsible for the hypocholestrolemic effect of soybean protein through the hydrophobic interaction between the peptides and bile salts in rats.

• Journal of Environmental Science International
• /
• v.5 no.3
• /
• pp.265-275
• /
• 1996

Air pollution characteristics and the influence of sea breeze on surface ozone concentration were studied using the data measured at 7 air quality continuous monitoring stations from June to September using 3 years (1990, 1993, 1994) in Pusan coastal area. Among the 246 sea breeze days for research Period, there were approximately 89 sea breeze days (36%) from lune to September, And there were 120 the episode days (68%) of ozone greater than or equal to 60 ppb in summer season. In 89 sea breeze days, the episode day was highly marked as 56 days (63%). So, we knew that the sea breeze greatly affects the occurence of ozone episode day. the ozone concentration under the condition of the sea breeze increase about 40% in the daytime. Frequencies distribution of $O_3$ concentration for sea breeze moved toward high concentration class. The characteristics of ozone concentration in relation to meteorological conditions of sea breeze is significant because we can discover major weather factors for eastablishing an air pollution- weather forecast system. For further. study about meterological approach method for photochemical air pollution, it is necessary to explain the characteristics of atmosphere below 1, 000 m, especially concerning the formation mechanism of inversion layers. And finally, we will study the relationships to synoptic weather conditions and vertical structure and diurnal variation of local wind systems including sea breeze, and the vertical movements of atmosphere in the city.

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.5
• /
• pp.450-456
• /
• 2010

This research was performed to develop the simple techniques to predict the copper concentration in alkaline copper quat (ACQ), copper azole (CUAZ), and bis-(N-cyclohexyl-diazeniumdioxy)-copper (CB-HDO) solutions. Two simple methods measuring the color due to copper compounds were evaluated by using a spectrophotometer. One is to directly measure the color of the preservative solutions. The other is to measure the color developed on the surface of a treated sample with the preservatives. The $L^*$ of the measured color values appeared to be the most sensitive to the change of copper concentration. The $a^*$ values of the preservative solutions tended to be decreased at above a certain concentration condition, and the $b^*$ values showed no trend with the concentration of copper compounds in preservative solutions. The surface color of the treated samples were changed from bluish to greenish as time passed. Both methods showed the high $R^2$ values of the regression models determined by using the lightness, which suggested that the methods might be applicable in preservative-treatment mills for the easy and fast prediction of the copper concentration.

• Proceedings of the SAREK Conference
• /
• 2008.11a
• /
• pp.275-280
• /
• 2008

The effects of the surfactant type, i.e., CTAB(cationic), SDS(anionic), and GA(polymeric), on the stability of 0.1 vol.% $Al_2O_3$ nanofluids were investigated. The changes in size and zeta potential of nanoparticles in nanofluids with pH, surfactant concentration, and time were experimentally observed. The nanofluids adding CTAB, which ionizes of the same charge with the bare particle surface, was found to have the best stability regardless of the surfactant concentration, whereas those with SDS became unstable under low surfactant concentration conditions, i.e. lower than the critical micellel concentration(CMC), before the charge reversal occurred. With higher SDS concentration over CMC, they became stable. Gum Arabic, which had been used often to stabilize the nanofluids, was also tested. In result, it was found that the type and concentration of surfactants to add should be selected considering pH and the sign of the bare particle surface charge.

• Journal of the Korean institute of surface engineering
• /
• v.57 no.2
• /
• pp.86-91
• /
• 2024

In this study, we investigated the effect of Na₂SiO₃ concentration on the Plasma Electrolytic Oxidation(PEO) film formation of Al6061 alloy. The morphology of the PEO films were examined by Optical Microscope(OM) and Scanning Electron Microscope(SEM). PEO film thickness increases as the Na₂SiO₃ concentration increases. The elemental analysis of PEO films was conducted using Dispersive X-ray Spectrometer(EDS). The cross-sectional elemental analysis result shows that the Si concentration tends to increase as the concentration of Na₂SiO₃ increases. X-Ray Diffraction(XRD) analysis was performed to confirm the degree of phase change according to Na₂SiO₃ concentration. In addition, Vickers hardness was measured to confirm the mechanical strength of the PEO film. As the concentration of Na₂SiO₃ increases, the hardness value also tends to increase.