• 대한조선학회지
• /
• 제21권1호
• /
• pp.35-42
• /
• 1984

In the present study, rotating bending fatigue tests have been carried out in three kinds of carbon steel specimens; an annealed low carbon steel, an annealed high carbon steel and quenched-tempered high carbon steel; with a small artificial surface defect that might exist in real structures. Fatigue crack lengths have been observed by a method of replication in order to investigate the growth characteristic of fatigue crack in the viewpoints of strength of materials and fracture mechanics. The main results obtained are as follows: 1) The effect of a small surface defect upon the reduction of fatigue limit is considerably large, and the rate of fatigue limit reduction grows in the following order; annealed low carbon steel(mild steel), annealed high carbon steel, quenched-tempered high carbon steel. 2) When the growth rate of surface crack length(2a) was investigated in the viewpoints of fracture mechanics based upon $ ${\Delta}K_{\varepsilon}$, the dependence of stress level and of surface defect size disappear, and there exists a linear relationships between d(2a)/dN and ${\Delta}K_{{\varepsilon}t},\;\Delta_{{\varepsilon}t}\sqrt{{\pi}a}$, on log. plot, i.e, $d(2a)/dN={C{\cdot}{\Delta}K_{\varepsilon}}^3_t$, where ${\Delta}_{{\varepsilon}t}\sqrt{{\pi}a}$ a is the cyclic total strain intensity factor range.

• 한국생산제조학회지
• /
• 제21권4호
• /
• pp.601-607
• /
• 2012

The magnetic abrasive polishing (MAP), for online monitoring with AE sensor attachment, was performed in this study. To predict the surface roughness after the magnetic abrasive polishing of NAK80, the signal data acquired from the AE sensor were analyzed. A dimensionless coefficient, which consisted of average of AErms and standard deviation of AE signal, was defined as a characteristic of the MAP and a prediction model was obtained using least square method. A neural network, which had multiple input parameters from AE signals and polishing conditions, was applied for predicting the surface roughness. As a result of this study, it was seen that there was very close correlation between the AE signal and the surface roughness in the MAP. And then on-line prediction of the surface roughness after the MAP of the NAK80 was possible by the developed prediction model.

• 한국산학기술학회논문지
• /
• 제12권5호
• /
• pp.2416-2424
• /
• 2011

본 연구는 건축에서 모듈화를 중심으로 한 기계적 생산에서 시리얼화를 중심으로 한 디지털 생산 체계로의 변화가 어떠한 방식으로 현대 건축의 외피 디자인 영향을 미치는지를 통해 디지털 기술의 발달이 건축 외피의 매체적 표현 양상의 구축과 적극적으로 공조하고 있음을 파악하려 한다. 이를 바탕으로 헤르죠그와 디모론의 2개의 전시시설의 분석을 통해 외피의 구현이 코드화와 이를 생산하기 위한 부재의 시리얼화라는 개념으로부터 가능하다는 사실을 밝히며 외피가 이미지의 즉각적인 표상을 통해 인간과의 지각적 소통이 가능한 매체적 방식으로 구현되는 과정에서의 디지털 디자인 기술의 역할과 의의를 파악하려 한다.

• 한국환경과학회지
• /
• 제3권1호
• /
• pp.1-9
• /
• 1994

We have Studied the characteristics of wind over Pusan coastal area in order to precisely predict surface wind having an important effect on oil spill fate using the data on surface observation of Pusan, Kimhae and Gadeogdo island which are collected during the 3 years from 1988 to 1990. We also investigated the correlation of the surface wind between Pusan, Kimhae and Gadeogdo island. In both Pusan areas and Kimhae, the land and sea breeze occurs during. the whole season except for winter. The occurrence frequency of land and sea breeze is significantly high from April to August. The correlation of surface wind between Pusan, Kimhae and Gadeogdo island surface wind is high in the daytime. The occurrence frequency of sea breeze in the Kimhae areas is higher than that in Pusan on the basis of the present criteria. For monthly occurrence, Pusan has the highest occurrence frequency of the sea breeze in August and Kimhae has in May.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.1080-1083
• /
• 2002

In this paper, we have studied with regard to the use of lasers for modifying the surface properties of silicon in order to improve it's wettability and adhesion characteristics. Using an Nd:YAG pulse laser, the wettability and adhesion characteristics of silicon surface have been developed by an Nd:YAG pulse laser. It was found that the laser treatment of silicon surfaces modified the surface energy. In the result of wetting experiments, by the sessile drop technique using the distilled water, wetting characteristic of silicon after the laser irradiation shows a decreased value of the contact angle. In case of the laser treated silicon surface, laser direct writing of copper lines has been achieved by pyrolytic decomposition of copper formate films$(Cu(HCOO)_2{\cdot}4H_2Q)$, using a focused $Ar^+$ laser beam$(\lambda=514.5nm)$ on the silicon substrates. The deposited patterns were measured by energy dispersive X-ray(EDX), Scanning Electron Microscopy(SEM) and surface profiler($\alpha$-step) to examine the cross section of deposited copper lines and linewidth.

• 폴리머
• /
• 제34권5호
• /
• pp.450-453
• /
• 2010

Iron(III) p-toluenesulfonate(FTS)를 개시제로 한 pyrrole의 중합에서 용액 중합법(LPP)과 기상 중합법(VPP)으로 제조된 PPy 박막의 전기/광학적 특성 및 표면구조를 비교하였다. LPP에 비해서 VPP 방법으로 제조된 PPy 박막은 우수한 전기적 특성을 보여주었다. 표면 특성분석을 이용하여 제조된 PPy 필름의 표면 모폴로지와 표면저항과의 상관관계를 검토하였다. VPP 방법으로 제조된 PPy 박막의 표면이 LPP로 제조된 것보다 평탄하였다. VPP를 응용한 잉크젯 프린팅과 소프트 리소그래피를 사용하여 미세 패턴된 PPy 박막을 효과적으로 제조할 수 있었다.

• 한국분무공학회지
• /
• 제6권4호
• /
• pp.22-30
• /
• 2001

The objective of this study is to develop the new equations for the calculation of higher heating values(HHVs) of reformed diesel fuels by ultrasonic treatment. Therefore, higher heating values of reformed diesel fuels by ultrasonic treatment are determined experimentally and calculated from their viscosity and surface tension measurements. The HHVs of the fuels are supposed to be a function of viscosity(Pa s) and surface tension(N/cm). The equations developed for the samples represent the correlation obtained by means of regression analysis. The HHVs calculated by developing new equations using viscosities showes the differences from the measured values ranging from -0.66 to 1.19 % and the correlation coefficient was -0.9411. The HHVs calculated by developing new equations using surface tensions showed the differences from the measured values ranging from -0.70 to 1.51 % and the correlation coefficient was 0.9999. The viscosity and the surface tension are characteristic properties of ultrasonic reformed diesel fuels for developing new formulae.

• 한국세라믹학회지
• /
• 제47권4호
• /
• pp.276-282
• /
• 2010

There are the impregnating layer formation by surface protective materials or impregnants and the adhesion method by polymer, FRP sheet or steel plate in the surface protective method of concrete structure. The surface impregnation method by impregnants improves the durability of concrete structure by modifying the structure of the concrete surface and also have a merit that can be shortly applied in place without the decrease of concrete surface appearance and is easily applied again. This study is interested in manufacturing the concrete surface impregnants including lithium and potassium silicate for the repair of the exposed concrete and the color concrete requiring the advanced function in view of the concrete appearance. The durability and porosity properties was tested for the review of application. The result of this study show that the effective content of silicate ranges 5 to 20% and the separate application of the first impregnant and the second impregnant is effective for the optimum performance. The adhesion in tension is slightly increased but the reinforcement of concrete substrate is slight. So, the concrete impregnant of this study is more desirable for the improvement of durability rather than the reinforcement.

• 한국전기전자재료학회논문지
• /
• 제20권3호
• /
• pp.234-239
• /
• 2007

This paper describes the TiW ohmic contact characteristics under the surface treatment of the polycrystalline 3C-SiC thin film grown on $SiO_2/Si(100)$ wafers by APCVD. The poly 3C-SiC surface was polished by using CMP(chemical mechanical polishing) process and then oxidized by wet-oxidation process, and finally removed SiC oxide layers. A TiW thin film as a metalization process was deposited on the surface treated poly 3C-SiC layer and was annealed through a RTA(rapid thermal annealing) process. TiW/poly 3C-SiC was investigated to get mechanical, physical, and electrical characteristics using SEM, XRD, XPS, AFM, optical microscope, I-V characteristic, and four-point probe, respectively. Contact resistivity of the surface treated 3C-SiC was measured as the lowest $1.2{\times}10^{-5}{\Omega}cm^2$ at $900^{\circ}C$ for 45 sec. Therefore, the surface treatments of poly 3C-SiC are necessary to get better contact resistance for extreme environment MEMS applications.

• Parasites, Hosts and Diseases
• /
• 제41권2호
• /
• pp.107-111
• /
• 2003

The surface ultrastructure of Acanthotrema felis (Trematoda: Heterophyidae) adults, recovered from a kitten experimentally infected with the metacercariae, was observed using a scanning electron microscope. The worm was leaf-like, ventrally concave and covered with scale-like multi-pointed tegumental spines. The spines on the anterior surface were short but broad, and had 10-12 pointed tips. The cytoplasmic processes protruded around the spines, like pockets for the spines. The ventrogenital opening was crescent, or kidney-shaped, and had protuberances with minute spines on its surrounding tegument. The spines on the posterior surface were long, but narrow, with 6-8 pointed tips. The cytoplasmic processes on this tegument were ridge-like, and elevated along the row of the spines. The surface ultrastructure of A. felis is generally similar to that of other heterophyid flukes, but some features are characteristic, and may be of taxonomic and bio-ecological significance.