• Journal of Welding and Joining
• /
• 제13권4호
• /
• pp.113-121
• /
• 1995

This study deals with the quality and the optimum range of laser cutting process. Cold rolled steel sheets for automobile application were cut by a high power CO$_{2}$ laser system with beam quality of TEM$_{\infty}$ mode. Both process parameters such as travel speed and assist gas pressure, and quality factors were considered to optimize the laser cutting. It was revealed that the thinner the sheet thickness, the less effect of oxidation energy for contributing the cutting process. High speed photographs demonstrated that molten spot on the cut surface moved in a random and vigorous manner according to its viscosity and the flowing direction of assist gas, which resulted in so called striation. Laser cutting produced a very smooth surface of average roughness(Ra) about less than 1.5.mu.m at the optimum range. It was also shown that the characteristics of dross formation was influenced by the flowing durection of assist gas and the fluidity of molten metal drop..

• Journal of Mechanical Science and Technology
• /
• 제15권7호
• /
• pp.859-865
• /
• 2001

This paper reports on the theoretical analysis of mixed lubrication for the piston ring. The analytical model is presented by using the average flow and asperity contact model. The cyclic variations of the nominal minimum oil film thickness are obtained by numerical iterative method. The total friction is calculated by using the hydrodynamic and asperity contact theory. The effect of the roughness height, pattern, and engine speed on the nominal minimum film thickness, friction force, ad frictional power losses are investigated. As the roughness height increases, the nominal oil film thickness and total friction force increase. Also, the effect of the surface roughness on the boundary friction is dominant at low engine speed and high asperity height. The longitudinal roughness pattern shows lower mean oil film pressure and thinner oil film thickness compared to the case of the isotropic and transverse roughness patterns.

• 한국표면공학회지
• /
• 제29권6호
• /
• pp.857-861
• /
• 1996

The influence of rf-plasma operation on the thin film formation containing small particles for Al-Li alloys mainly have been studied as a function of Ar gas pressure and plasma power by means of a 200kV transmission electron microscope (TEM). Under the non-plasma operation, the transition from continuous thin films to clusters of grape-like small particles occurred at Ar gas pressures above 20Pa. Particles were single crystals with clear crystal habit planes. Under the plasma operation, the influence of gas pressures on the film formation at a plasma power of 5W was also examined. Thin films containing particles below 30Pa and the films containing mainly particles above 40Pa were formed. The prominent change of the average particle size was not recognized. The increase of the plasma powers at 20Pa, which formed particles under non-plasma, suppressed growth of particles, and homogeneous films containing very small particles were fabricated. The electric conductivity showed slight decrease with an increase of plasma power.

• 한국수자원학회논문집
• /
• 제56권spc1호
• /
• pp.1049-1058
• /
• 2023

보와 저낙차 댐과 같은 하천횡단구조물을 통과하는 흐름은 도수 현상을 동반하는 급변류가 지배적이다. 구조물 하류에서 도수로 인한 유속과 수면의 강한 비정상성은 수공구조물의 안정에 영향을 줄 수 있다. 특히, 높은 Froude 수 조건에서 발생하는 정상도수는 공기연행이 현저하게 발생하여 흐름 특성은 더욱 복잡해진다. 이 연구에서는 Froude 7.3 조건에서 발생하는 정상도수를 모의하기 위해서 큰와모의 기법과 하이브리드 VoF 기법을 이용한 수치모의를 수행하였다. 수치모의 결과는 구조물 하류 바닥면에서 계측된 순간최대압력과 시간평균압력 분포를 유사하게 재현하는 것으로 나타났다. 단, 구조물 직하류에서의 순간최소압력 분포는 대상으로 하는 실험 계측값과 반대의 양상을 보이지만, 유사한 다른 시험과는 같은 양상을 보임으로써 본 연구에서 수행한 수치모의는 합리적으로 압력변동을 예측하는 것으로 판단된다. 도수 중앙부에서의 연직방향 유속분포와 공기농도분포는 유사한 조건의 실험 결과들과 자기상사성을 보이면서 양호하게 일치하는 것으로 나타났다. 이러한 결과는 본 연구에서 적용한 큰와모의 기법과 하이브리드 VoF 기법이 높은 Froude 수 조건에서 강한 공기연행을 동반하는 도수현상을 양호하게 재현할 수 있음을 보여준다.

• 한국표면공학회지
• /
• 제56권3호
• /
• pp.192-200
• /
• 2023

Graphene, a two-dimensional material, has shown great potential in a variety of applications including microelectronics, optoelectronics, and graphene-based batteries due to its excellent electronic conductivity. However, the production of large-area, high-quality graphene remains a challenge. In this study, we investigated graphene growth on electrolytic copper foil using thermochemical vapor deposition (TCVD) to achieve a similar level of quality to the cold-rolled copper substrate at a lower cost. The combined effects of pre-annealing time, graphenized temperature, and partial pressure of hydrogen on graphene coverage and domain size were analyzed and correlated with the roughness and crystallographic texture of the copper substrate. Our results show that controlling the crystallographic texture of copper substrates through annealing is an effective way to improve graphene growth properties, which will potentially lead to more efficient and cost-effective graphene production. At a hydrogen partial pressure that is disadvantageous in graphene growth, electrolytic copper had an average size of 8.039 ㎛², whereas rolled copper had a size of 19.092 ㎛², which was a large difference of 42.1% compared to rolled copper. However, at the proper hydrogen partial pressure, electrolytic copper had an average size of 30.279 ㎛² and rolled copper had a size of 32.378 ㎛², showing a much smaller difference of 93.5% than before. This observation suggests this potentially leads the way for more efficient and cost-effective graphene production.

• 한국응용과학기술학회지
• /
• 제26권1호
• /
• pp.102-108
• /
• 2009

Behaviors of saturated fatty acid halides (CI4, C16, C18) were measured by LB method when the molecules were stimulated by pressure. The saturated fatty acid halides were deposited on the indium tin oxide(lTO) glass by the LB method. The average organic ultra thin film size and the surface roughness of the fatty acid halides thin films were investigated using AFM. It was found that AFM images show small surface roughness ($2.5{\sim}5.0\;nm$) and the organic ultra thin film size of $2.5{\sim}12\;nm$. Both aggregations and pin-holes were also seen on the AFM images. However we found that the surface roughness. These effects seem to be reasonable to be related to the increase of the organic ultra thin film size of fatty acid halides.

• Bulletin of the Korean Chemical Society
• /
• 제34권12호
• /
• pp.3805-3810
• /
• 2013

The surface modification of silica particles (SPs) was systemically conducted by the treatment of 0.1-10 wt % phenylsilanetriol (PST) on the basis of SPs used through two step processes: 1) the PST coating of SPs via evaporation under reduced pressure and 2) their thermal condensation leading to Si-O-Si bond formation via heating at $130^{\circ}C$. The evaluation of the modified SPs was conducted by the simple floating test on water and the measurement of the contact angle (CA) of water droplet on the 2-dimensional layer of modified SPs on slide glass. When PST was used about 2 wt % or above on the basis of SPs (about average size: 50 nm) used, the modified SPs were fully floated on the water and all dispersed into upper organic solvent layer after a shaking with the mixture of the water and benzene, indicating that the modified SPs have hydrophobic properties. The modified SPs were characterized by $^{29}Si$ MAS NMR and physicochemical properties including SEM, TEM, BET, adsorption/desorption isotherms, etc. were measured and compared each other in details. This research demonstrates that the organosilanetriol is a good modifier applicable for the surface modification of inorganic oxide particles using a low amount of modifier on the basis of oxide particles used.

• 한국세라믹학회지
• /
• 제50권2호
• /
• pp.122-126
• /
• 2013

The surface roughness of the inner and outer surfaces of a tube is an important requirement for nuclear fuel cladding. When an inner SiC clad tube, which is considered as an advanced Pressurized Water Cooled Reactor (PWR) clad with a three-layered structure, is fabricated by Chemical Vapor Deposition (CVD), the surface roughness of the substrate, graphite, is an important process parameter. The surface character of the graphite substrate could directly affect the roughness of the inner surface of SiC deposits, which is in contact with a substrate. To evaluate the effects of the surface roughness changes of a substrate, SiC deposits were fabricated using different types of graphite substrates prepared by the following four polishing paths and heat-treatment for purification: (1) polishing with #220 abrasive paper (PP) without heat treatment (HT), (2) polishing with #220 PP with HT, (3) #2400 PP without HT, (4) polishing with #2400 PP with HT. The average surface roughnesses (Ra) of each deposited SiC layer are 4.273, 6.599, 3.069, and $6.401{\mu}m$, respectively. In the low pressure SiC CVD process with a graphite substrate, the removal of graphite particles on the graphite surface during the purification and the temperature increasing process for CVD seemed to affect the surface roughness of SiC deposits. For the lower surface roughness of the as-deposited interlayer of SiC on the graphite substrate, the fine controlled processing with the completed removal of rough scratches and cleaning at each polishing and heat treating step was important.

• Wind and Structures
• /
• 제10권6호
• /
• pp.495-510
• /
• 2007

Wind pressure data have been collected on the tiled roof of a full-scale test house at Silsoe in the UK. The tiled roof was of conventional UK construction with a batten-space and bitumen-felt underlay beneath the interlocking concrete tiles. Pressures were monitored on the outer surface of selected tiles, at several locations within the batten-space, and beneath the underlay. Data were collected both with and without ventilator tiles installed on the roof. Little information appears to exist on the share of wind load between tiles and underlays which creates uncertainty in the design of both components. The present study has found that for the critical design case of maximum uplifts it would be appropriate to assign 85% of the net roof load to the tiles and 15% to the underlay when an internal pressure coefficient of -0.3 is used, and to assign 60% to the tiles and 50% to the underlay when an internal pressure coefficient of +0.2 is assumed (an element of design conservatism is inherent in the apparent 110% net loading indicated by the latter pair of percentage values). These findings indicate that compared with loads implied by BS 6399-2, UK design loads for underlay are currently conservative by 25% whilst tile loads are unconservative by around 20% in ridge and general regions and by around 45% in edge regions on average over roof slopes of $15^{\circ}-60^{\circ}$.

• 대한조선학회논문집
• /
• 제43권5호
• /
• pp.578-585
• /
• 2006

Cavitation related erosion damages on semi-spade rudder generally occur at around leading edge of lower-face and behind gap of lower pintle. To get the idea of gap entrance profile for the latter case, a series of tests with large models has been carried out at MOERI. In the tests, the flow pattern around lower pintle have been investigated and visualized by high speed camera. Additionally, cavitation inception tests and pressure measurements have also been conducted for better comparison. As a result a new model (F rudder) has been developed. The new model turned out to have stable pressure distribution along the surface and so the cavitation inception speeds within ${\pm}5^{\circ}$ of rudder angle were delayed approx. 4 knots in average.