• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.7
• /
• pp.635-640
• /
• 2005

In this paper, we have improved a novel high tilted optically compensated bend (OCB) (HTOCB) mode by using high tilt angle that was generated by the unique baking condition on the homeotropic alignment layer. The high tilt angle of liquid crystal (LC) was generated by new alignment process that tilt angle changed homeotropic state to homeogenous state using Hot-plate equipment; we obtained about $40\~50^{\circ}$ tilt angle with negative and positive dielectric anisotropy on the homeotropic polyimide (PI), and then LC tilt angle decreased as increasing baking temperature and time. At last, we obtained about $10^{\circ}$ with positive type NLC $({\Delta}n>0)$. Also, the LC tilt angle of positive type NLC $({\Delta}n>0)$ decreased as increasing rubbing strength at the same baking temperature and time. The novel LC operating mode (HTOCB) that used the high tilt angle by the new alignment method was improved. The response time of the novel HTOCB cell was faster than that of conventional OCB cell. We suggest that the developed the novel HTOCB cell using control of tilt angle on the homeotropic surface is a promising technique for the achievement of a fast response time and a high contrast ratio.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.223-228
• /
• 2001

This study was obtained the pressure distribution of a falling body that is deadrise angle $0^{\circ}$ and deadrise angle $5^{\circ}$ upon a water surface by the experiment with the impact machine. The theoretical equation was obtained the air region and the interface and the water region which devide 3 parties between the body and the water surface for an investigation of the complete phenomena. Pressure distributions and histories compare favorably with available experimental data. The numerical results are similar to the experimental results for the impact force type with $Fo(1+cos{\pi}t/tc)$.

• Korean Journal of Computational Design and Engineering
• /
• v.4 no.2
• /
• pp.110-120
• /
• 1999

In general, turbine blades are usually machined on 5-axis NC machine. The 5-axis machining of sculptured surface offers many advantages over 3-axis machining including the faster material-removal rates and an improved surface finish. But it is difficult and time-consuming to generated interference-free 5-axis tool path. This paper describes research on the algorithm for generation of an interference-free 5-axis NC data for machining turbine blades. The approach, using the section profile derived from the intersection of cutting planes with a triangulated-surface approximation, includes (1) CL-data generation by detecting an interference-free heel angle (2) the calculation method for finding a adaptive feed-rate value, and (3) the inverse kinematics depending on the structure of 5-axis machine.

• Electrical & Electronic Materials
• /
• v.8 no.2
• /
• pp.136-143
• /
• 1995

With the contact angle of phase dropping epoxy resin on the inorganic filler(glass plate) surface treated with air plasma, we have studied about the interfacial wettability between epoxy resin and glass plate as a simple model of glass fiber reinforced composite materials. The contact angle on the inorganic filler surface varied with surface treatment conditions. The contact angle significantly depends on plasma treating time and environment temperature in the oven. From the view point of plasma treatment condition in this work, when discharge conditions were pressure 200mtorr, voltage 800V, magnetic flux density 8OGauss, optimum treatment time were proved as 3,4 and 5 minutes for the environment of >$80^{\circ}C$, >$100^{\circ}C$ and >$120^{\circ}C$, respectively.

• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.578-582
• /
• 2004

This paper presents the response surface optimization method using three-dimensional Navier-Stokes Analysis to optimize the shape of a axial flow fan. Reynolds-averaged Navier-Stokes equations with k-$\epsilon$ turbulence model are discretized with finite volume approximations. Regression analysis is used for generating response surface, and it is validated by ANOVA. Five geometric variables, i.e., distribution of sweep angle at mean and tip, lean angle at mean and tip, and spanwise location of mean were employed to optimize the efficiency. The computational results are compared with experiment data. As a main result of the optimization, the efficiency was successfully improved.

• Journal of Korean Academy of Oral and Maxillofacial Radiology
• /
• v.23 no.2
• /
• pp.207-211
• /
• 1993

The auther has evaluated the panoramic image of the mandibular condyle according to its horizontal codylar angle(0°, 10°, 20°, 30°, 40°) and intercondylar distance( 9.5, 11.0, 12.5, 14.0㎝). The Results were as follows: 1. In all horizontal condylar angle, the farther the intercondylar distance was, the smaller the horizontal length in radiogram was. 2. The increased the horizontal condylar angle was, the longer in horizontal direction and the shorter in vertical direction the image of superior condylar surface was. 3. In case of large horizontal condylar angle, the real mesial surface of condyle was projected to the posterior surface on radiograph.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.259-262
• /
• 1998

The liquid crystal (LC) alignment and pretilt angle generation using photo-alignment method were investigated in this study. We obtained that the monodomain alignment of nematic(N) LC increases with increasing irradiation time in a cell with linearly polarized ultraviolet (LPUV) light irradiation on polyimide (Pl) surfaces. We consider that the monodomain alignment is able to be anisotropic dispersion force due to photo-depolymerization of polymer with LPUV light irradiation on Pl surface. Also, we observed that the uniform alignment of NLC is obtained in a cell with normally LPUV light irradiated on Pl surface at 30 min. and then oblique LPUV is secondly irradiated on Pl surfaces rotated by 90$^{\circ}$. The pretilt angle of NLC is generated about 1.5$^{\circ}$ with oblique angle 60$^{\circ}$.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.11a
• /
• pp.71-74
• /
• 2000

In this study, the optimal condition of surface treatment for aluminum panel was determined by measuring the contact angle and T-peel strength. The contact angle was measured for various mixture ratios of acetylene gas and nitrogen gas. The mixture (acetylene gas to nitrogen gas) ratios used were 1:9, 3:7, 5:5, 7:3, and 9:1. The contact angle was also measured as a function of time of surface treatment. The results showed that the contact angle was a minimum for mixture ratio of 5:5. T-peel strength was a maximum for the treatment time of 30 second.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1995.05a
• /
• pp.157-168
• /
• 1995

Ignition of a reactive solid with rough surface by constant heat flux is studied. The geometry of surface is represented by a protrusion in shape of cone of infinite length. Ignition time and ignition criterion versus apex angle are determined, with the use of heterogeneous model of ignition. To study the effect of geometry on ignition the results are compared with the known results for the one-dimensional ignition of the semi-infinite body. It is shown, that: a) ignition time depends strongly upon the apex angle and is proportional to the angle to the second power; b) ignition criterion and ignition temperature do not depend strongly on angle. The ignition delay and the energy required for the successful ignition are substantially reduced compared to the one-dimensional case.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.12 no.1
• /
• pp.81-87
• /
• 1999

The surface morphology of liquid crystal alignment layer has been investigated by using Brewster angle microscope(BAM) for the first time. The samples used in this work for liquid crystal alignment layer were mechanically rubbed polyimide films. The rubbing pattern on this layer has been analyzed with the terms of microgroove and rubbing induced optical birefringence. For the mechanically rubbed surface, the geometrical factors of microgroove play the major role for the formation of rubbing pattern. We propose that the BAM can be used as a powerful tool not only for observing the rubbing pattern, but also for inspecting the surface defects.