• 구강회복응용과학지
• /
• 제40권3호
• /
• pp.149-158
• /
• 2024

목적: 본 연구의 목적은 임시 수복물의 제작 방법과 표면 연마가 표면 거칠기와 세균 부착에 미치는 영향을 in vitro 실험을 통해 알아보고자 함이다. 연구 재료 및 방법: 120개의 원통형 임시 수복 레진 블록(10 × 10 × 2.5 mm)을 네 가지 제작 방식(Conventional, CAD/CAM milling, DLP 3D printing, LCD 3D printing)에 따라 제작하였고, 각 군당 30개의 시편을 배정하였다. 이후 연마를 시행하지 않은 군(NP), #400 grit SiC 연마군, #800 grit SiC 연마군으로 나누어 10 × 10 × 2 mm 시편 사이즈가 되도록 연마하였다(n = 10). 표면조도측정기(Surftest Extreme SV-3000S4, Mitutoyo, Kanagawa, Japan)를 이용하여 시편의 표면 거칠기 Ra와 Ry를 측정하였다. 각 군에서 3개의 시편을 추출하여 시편을 인공 타액으로 코팅 후, 시편에 Streptococcus mutans를 4시간 동안 37℃에서 배양하였다. 배양한 시편을 고정액에 고정시켜 주사전자현미경(S-4800, Hitachi, Chiyoda, Japan) 사진을 촬영하였다. 통계 분석은 표면 거칠기 Ra, Ry에 대해 각각 two-way ANOVA (P = 0.05) 후 Scheffe test (P = 0.05)로 사후 검정 시행하였다. 결과: 임시 수복물의 제작 방식과 표면 연마 정도는 표면 거칠기 Ra와 Ry 모두에 유의한 영향을 주었고, 상호작용 효과가 있었다. Ra 값은 NP 군에서 제작 방식에 따라 유의한 차이가 있었다. Ry 값은 NP, #800 군에서 제작 방식에 따라 유의한 차이가 있었다. DLP와 LCD 군은 모든 연마군에서 Ra, Ry 값이 유의한 차이가 없었다. 결론: 임시 수복물의 제작 방식과 표면 연마는 표면 거칠기에 유의한 영향을 보였고 S. mutans 부착에 대해 다른 부착 양상을 보였다.

• Design & Manufacturing
• /
• 제17권2호
• /
• pp.22-26
• /
• 2023

As Light-Emitting Diodes(LEDs) continue to advance in performance, their application in automotive lamps is increasing. Automotive LEDs utilize light guides not only for aesthetics but also to control light quantity and direction. Light guides employ patterns of a few hundred micrometers(㎛) to regulate the light, and the surface roughness(Ra) of these patterns can reach tens of nanometers(nm). Given that these light guides are produced through injection molding, mold processing technology with high surface quality micro-patterns is required. This study serves as a preliminary investigation into the development of high surface quality micro-pattern processing technology. It examines the surface roughness of the workpiece based on the cutting direction of the pattern and the cutting fluid type when cutting micro-patterns on STAVAX steel using cubic Boron Nitride(cBN) tools. The experiments involved machining a step-shaped micro-pattern with a height of 60 ㎛ and a pitch of 400 ㎛ in a 22×22 mm area under identical cutting conditions, with only the cutting direction and cutting fluid type being varied. The machining results of four cases were compared, encompassing two cases of cutting direction(parallel to the pattern, orthogonal to the pattern) and two cases of cutting fluid type (flood, mist). Consequently, the Ra value was found to be the highest(Ra 128.33 nm) when machining with the flood type in parallel to the pattern, while it was the lowest(Ra 95.22 nm) when machining with the mist type orthogonal to the pattern. These findings confirm that there is a difference of up to 25.8 % in the Ra value depending on the cutting direction and cutting fluid type.

• Journal of the Optical Society of Korea
• /
• 제10권1호
• /
• pp.48-54
• /
• 2006

White-light scanning interferometry (WLI) and phase shifting interferometry (PSI) are increasingly used for surface topography measurements, particularly for areal measurements. In this paper, we compare surface profiling results obtained from above two optical methods with those obtained from stylus instruments. For moderately rough surfaces ($Ra{\approx}500\;nm$), roughness measurements obtained with WLI and the stylus method seem to provide close agreement on the same roughness samples. For surface roughness measurements in the 50 nm to 300 nm range of Ra, discrepancies between WLI and the stylus method are observed. In some cases the discrepancy is as large as 109% of the value obtained with the stylus method. By contrast, the PSI results are in good agreement with those of the stylus technique.

• Design & Manufacturing
• /
• 제17권1호
• /
• pp.33-39
• /
• 2023

The ball end mill is a type of cutting tool that is widely used to process complex mold shapes including aspheric surfaces. Unlike the flat end mill in which the cutting edge is formed on the cylindrical handle, the cutting edge is formed from the cylindrical handle to the hemispherical shape, which is advantageous for processing curved shapes. However, since the cutting speed continuously changes during machining due to the helix angle of the cutting edge or the machining inclination angle, it is difficult to obtain a precise machined surface. Therefore, in this paper, machining was performed while changing the helix angle of the ball end mill and the angle of the machining slope under the same cutting conditions for STD 11 material, which is widely used as a mold material. Through this, the effect of the two variables on the roughness of the machined surface was analyzed. As a result, if the helix angle was 0 degrees, it showed the best surface roughness of Ra. 0.16 ㎛. When the helix angle was 20 degrees, the best surface roughness of Ra. 0.18 ㎛ was occurred.

• 한국정밀공학회지
• /
• 제17권5호
• /
• pp.131-136
• /
• 2000

This paper is concerned with the surface roughness and the bending strength of ground workpiece in ZrO2 ceramic grinding. Surface roughness was measured with surface tracer and bending strength value was obtained by three-point bending test on machining center using tool dynamometer. Grinding experiments were carried out to examine the effects of grinding conditions including diamond mesh size, table speed, and depth of cut on ground surface roughness. The correlation between surface roughness and bending strength was also inspected. The experimental results indicate that the rougher surface is produced as the mesh size of diamond wheel is reduced and table speed is increased, but surface roughness is not affected by depth of cut. The values of bending strength decrease as the values of Ra, Rmax and Ku increase.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 춘계학술대회논문집 - 한국공작기계학회
• /
• pp.465-470
• /
• 2000

This paper is concerned with the surface roughness and the bending strength of ground workpiece in ZrO2 ceramic grinding. Surface roughness was measured with surface tracer and bending strength value was obtained by three-point bending test on machining center using tool dynamometer. Grinding experiments were carried out to examine the effects of grinding conditions including diamond mesh size, table speed, and depth of cut on ground surface roughness. The correlation between surface roughness and bending strength was also inspected. The experimental results indicate that the rougher surface was produced as the mesh size of diamond wheel is reduced and table speed is increased, but surface roughness is not affected by depth of cut. The values of bending strength decrease as the values of Ra, Rmax and Ku increase.

• 한국안전학회지
• /
• 제19권3호
• /
• pp.14-19
• /
• 2004

The objective of the present work is to examine evaporation cooling of droplet due to surface roughness under radiative heat input condition. The surface temperatures varied from $80\~160^{\circ}C$ on aluminum alloy (AL 2024) and surface roughness was $0.18{\mu}m,\;1.36{\mu}m$. The results are as follows; Regardless of surface roughness under radiative heat input condition, as droplet diameter is larger, the in-depth temperature of solid decreases and evaporation time increases. In the case of $0.18{\mu}m\;and\;1.36{\mu}m$ of surface roughness, the larger the surface roughness is, the less the evaporation time is and the larger the temperature within the solid is. In the case of $Ra=0.18{\mu}m$ evaporation time and time averaged heat flux for radiative heat input case is shorter than for the conductive case.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1873-1876
• /
• 2003

Magneto-rheological polishing is a new technology used in precision polishing. It utilizes magneto-rheological fluid. nonmagnetic polishing abrasive, aqueous carrier fluids in magnetic field to remove material from a part surface. Silicon micro channel as work piece is fixed in the slurry which is made of MR fluid and CeO$_2$(10 vol%) abrasive particles. And permanent magnet rotate in the slurry to transfers magnetic force to abrasive particles by increasing yield strength of MR fluid. so, the obtained bottom surface roughness of micro channel by experiment reduced to Ra 0.010 $\mu\textrm{m}$ Rmax 0.103 $\mu\textrm{m}$ and finwall surface roughness of micro channel reduced to Ra 0.018 $\mu\textrm{m}$ Rmax 0.468 $\mu\textrm{m}$. At optimum conditions of variables, the workpiece as silicon micro channel have about 24 times smaller surface roughness than before polishing.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.519-524
• /
• 1999

To manufacture alumina products, sintering and grinding process are needed. In Al2O3 grinding, macro/micro surface fracture and cracks are easily occurred on the ground surface because of its high brittleness. In view point of fatigue fracture, surface profile produced by grinding is considered as notches. Therefore, it was reasonable that magnitudes and shapes of surface profiles effects on fatigue strength and life. Particularly, surface finish of Al2O3 which have high hardness and brittleness have an effect on fatigue strength. In this paper, some experiments are carried out to examine influence of grinding conditions to magnitude and shape of surface profile as well as the relationships of Ra, Rmax, Rmax/Ra, and Ku. Through the experimental results, It is found that Ra and Rmax was affected by grinding conditions, but Rmax/Ra and Ku was not. There are linear relations between Ra and Rmax, and between Rmax/Ra and Ku.

• 한국기계가공학회지
• /
• 제1권1호
• /
• pp.133-140
• /
• 2002

The object of this paper is to predict the surface roughness using the experiment equation of surface roughness, which is developed with a full factorial design in turning. $3^3$ full factorial design has been used to study main and interaction effects of main cutting parameters such as cutting speed, feed rate, and depth of cut, on surface roughness. For prediction of surface roughness, the arithmetic average (Ra) is used, and stepwise regression has been used to check the significance of all effects of cutting parameters. Using the result of these, the experimental equation of surface roughness, which consists of significant effects of cutting parameters, has been developed. The coefficient of determination of this equation is 0.9908. And the prediction ability of this equation was verified by additional experiments. The result of that, the coefficient of determination is 0.9718.