• Journal of computational fluids engineering
• /
• v.10 no.3 s.30
• /
• pp.1-8
• /
• 2005

In this study, unsteady aerodynamic analyses of a wedge-type airfoil based on nonlinear piston theory and Euler equations have been performed in supersonic and hypersonic flows. The third-order nonlinear piston theory (NPT) to calculate unsteady lift and moment coefficients is derived and applied in the time-domain. Also, unsteady flow quantities are obtained from the two-dimensional time-dependent Euler equations. For the CFD based unsteady aerodynamic analyses, an arbitrary Lagrangean-Eulerian (ALE) formulation for the Euler equations is used to calculate flow fluxes in the computational flow field with moving boundaries. Numerical comparisons for unsteady lift and moment coefficients are presented between NPT and Euler approaches. The results show very good agreements in the high supersonic and hypersonic flows. It means that the present NPT can be efficiently used to predict unsteady aerodynamic forces ol wedge type airfoils with dynamic motions in the high supersonic and hypersonic flow regimes.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.11 no.4
• /
• pp.20-28
• /
• 2008

Missile operating at supersonic conditions experiences considerable high temperature environments that is caused by aerodynamic heating as a result of the temperature gradient through boundary layer that surrounds it. This is one of important problems to the designer due to temperature limitation of structural materials. Because prediction of aerodynamic heating on missile needs unsteady calculation according to a flight trajectory, approximate method approach is efficient at design stage. In this paper, improved aerodynamic heating analysis scheme is introduced, which calculates heat flow and temperature by simple pressure field prediction on a missile body and fin. The prediction results are compared with measured data and MINIVER codes results.

• 한국전산유체공학회:학술대회논문집
• /
• 2004.10a
• /
• pp.173-176
• /
• 2004

In this study, the multidisciplinary aerodynamic-structural optimal design is carried out for the supersonic fighter wing. Through the aeroelastic analyses of the various candidate wings, the aerodynamic and structural performances are calculated such as the lift coefficient, the drag coefficient and the deformation of the wing. In general, the supersonic fighter is maneuvered under the various flight conditions and those conditions must be considered all together during the design process. The multi-point design, therefore, is deemed essential. For this purpose, supersonic dash, long cruise range and high angle of attack maneuver are selected as representative design points. Based on the calculated performances of the candidate wings, the response surfaces for the objectives and constraints are generated and the supersonic fighter wing is designed for better aerodynamic performances and less weights than the baseline. At each design point, the single-point design is performed to obtain better performances. Finally, the multi-point design is performed to improve the aerodynamic and structural performances for all design points. The optimization results of the multi-point design are compared with those of the single-point designs and analyzed in detail.

• Journal of computational fluids engineering
• /
• v.10 no.2
• /
• pp.54-59
• /
• 2005

For the improvement of aerodynamic performance of the turbine blade in a turbopump for the liquid rocket engine, the optimization of turbine profile shape has been studied. The turbine in a turbopump in this study is a partial admission of impulse type, which has twelve nozzles and supersonic inflow. Due to the separated nozzles and supersonic expansion, the flow field becomes complicate and shows oblique shocks and flow separation. To increase the blade power, redesign ol the blade shape using CFD and optimization methods was attempted. The turbine cascade shape was represented by four design parameters. For optimization, a genetic algorithm based upon non-gradient search hue been selected as an optimizer. As a result, the final blade has about 4 percent more blade power than the initial shape.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.8 no.2 s.21
• /
• pp.77-87
• /
• 2005

The thermomechanical characteristics were evaluated for 17-4PH stainless steel widely used in supersonic airframe subjected to both aerodynamic loading and heating. The thermomechanical tests were conducted under both elevated temperature and rapid heating condition from $1^{\circ}C/sec\;to\;28^{\circ}C/sec$. The thermomechanical behaviors under rapid heating were compared with those of elevated temperature after 1/2 hour exposure in terms of yield stress to investigate the influence of heating rates. A heating rate-yield temperature parameter was suggested for rapid heating based on time-temperature parameters, and master yield stress curve was obtained by using these parameters. The experimental results and methodology from this study can be used as basic engineering data when designing supersonic vehicle structures subjected to aerodynamic loading and severe heating environment.

• International Journal of Aeronautical and Space Sciences
• /
• v.17 no.2
• /
• pp.260-267
• /
• 2016

The design process of blended inlet body (BIB) for the preliminary design of a near-space high supersonic unmanned aerial vehicle (HSUAV) is presented. The mass flow rate and cowl area of inlet at a design point are obtained according to the cruise condition of the HSUAV. A mixed-compression axisymmetric supersonic inlet section with a fixed geometry reasonably matching the high supersonic cruise state is created by using the inviscid theory of aerodynamics. The inlet section is optimized and used as a baseline section for the BIB design. Three BIB concepts for the HSUAV are proposed, and their internal aerodynamic characteristics of inlet are evaluated using Euler computational fluid dynamics (Euler CFD) solver. The preferred concept is identified, in which the straight leading edge of the baseline HSUAV configuration is modified into the convex leading edge to accommodate the inlet and meet the requirements of the cowl area to capture the sufficient air flow. The total recovery of inlet for the preferred BIB concept and the aerodynamic characteristics of the modified HSUAV configuration are verified using Navier-Stokes computational fluid dynamics (NS CFD) solver. The validation indicates that the preferred BIB concept can meet both the requirements of the inlet and aerodynamic performance of the HSUAV.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.87-90
• /
• 2002

Computational study has been undertaken to investigate the aerodynamic influence of side jet on a supersonic missile and to find a similarity condition between the flight condition and the wind tunnel testing. Tasks were performed to validate the existing Raytheon test body with side jet, to simulate the flow inside the supersonic wind tunnel, and to compare the flow fields between the missile in free flight and that in the wind tunnel. Then sub-scale model of body-tail configuration was analyzed to estimate the influence of the side jet on the missile components. It Is found that the influence of side Jet is not as significant on the tail region as on the body surface and a simple algebraic formula for aerodynamic coefficients accounting for the side jet as a point force may be cautiously utilized in setting up control logic.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.10
• /
• pp.112-117
• /
• 2004

This work is on numerical and experimental studies on the new type igniter using aerodynamic energy. The aerodynamic igniter consists of a nozzle and a resonance tube. The supersonic jet from a nozzle coming into the resonance tube generates pressure oscillation between the nozzle and the resonator. This oscillation changes the kinetic energy to thermal energy in the resonator under a certain condition. In this study, sonic and supersonic nozzles were tested in two different resonators, results has been compared. And geometrical optimum values of a supersonic nozzle has been suggested to reduce aerodynamic loss and friction in the expanded surface of the nozzle.

• 한국전산유체공학회:학술대회논문집
• /
• 2010.05a
• /
• pp.308-314
• /
• 2010

In this study, NASA test model with four cruciform fins is utilized to validate the in-house code. Sur face pressure distribution and aerodynamic coefficients are compared with experimental data. Through extensive validation work, it is verified that the code has capability to predict aerodynamic characteristics of missile configuration. In inviscid analysis through a relatively low computational time, analysis result close to experimental data can be confirmed. However, at high angle of attack more than 20 degree, the accuracy of analysis is gradually decreased due to massive separation. In addition, it has been seen that Reynolds number, turbulence model and numerical method have effects on body vortices and aerodynamic characteristics.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.335-338
• /
• 2010

A recent study for tracing the profiles of supersonic axisymmetric Minimum Length Nozzle with uniform and parallel flow at the exit section, the stagnation temperature is taken into account. The aim of this work is to add optimization algorithm to the supersonic nozzle design in order to get the optimum nozzle shape. The comparisons of the nozzle contours based on the method of characteristics are presented. The specific heats and their ratio vary with the stagnation temperature when this temperature of a perfect gas increases. An application is made for air in a supersonic nozzle.