• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.3
• /
• pp.53-61
• /
• 1999

Impinging jets are observed when exhaust gases from missiles or V/STOL aircrafts impinge on the ground, flame deflector, ship deck, etc. The flow shows different patterns according to the nozzle geometry, nozzle-to-plate distance, and plate angle, for example. This paper describes experimental works on the phenomena (pressure distribution, occurrence of stagnation bubble, and so on.) when underexpanded supersonic jets impinge on a perpendicular flat plate using a supersonic cold-flow system, and compares the results with those obtained using a shock tunnel. The flow characteristics for the supersonic cold-flow system were also investigated. Surface pressure distribution of supersonic cold-flow system differed from that of shock tunnel because of water and temperature in the low-pressure chamber. Surface pressure distribution as to underexpanded ratio showed similar patterns together.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.321-325
• /
• 2010

Supersonic ejectors are simple mechanical components, which generally perform mixing and/or recompression of two fluid streams. Ejectors have found many applications in engineering. In aerospace engineering, they are used for altitude testing of a propulsion system by reducing the pressure of a test chamber. It is composed of three major sections: a vacuum test chamber, a propulsive nozzle, and a supersonic exhaust diffuser. This paper aims at the improvement of ejector-diffuser performance by focusing attention on reducing exhaust back flow into the test chamber, since alteration of the backflow or recirculation pattern appears as one of the potential means of significantly improving low supersonic ejector-diffuser performance. The simplest backflow-reduction device was an orifice plate at the duct inlet, which would pass the jet and entrained fluid but impede the movement of fluid upstream along the wall. Results clearly showed that the performance of ejector-diffuser system was improved for certain a range of system pressure ratios, whereas the orifice plate was detrimental to the ejector performance for higher pressure ratios. It is also found that there is no change in the performance of diffuser with orifice at its inlet, in terms of its pressure recovery. Hence an appropriately sized orifice system should produce considerable improvement in the ejector-diffuser performance in the intended range of pressure ratios.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.318-322
• /
• 2009

Supersonic ejectors are simple mechanical components, which generally perform mixing and/or recompression of two fluid streams. Ejectors have found many applications in engineering. In aerospace engineering, they are used for altitude testing of a propulsion system by reducing the pressure of a test chamber. It is composed of three major sections: a vacuum test chamber, a propulsive nozzle, and a supersonic exhaust diffuser. This paper aims at the improvement of ejector-diffuser performance by focusing attention on reducing exhaust back flow into the test chamber, since alteration of the backflow or recirculation pattern appears as one of the potential means of significantly improving low supersonic ejector-diffuser performance. The simplest backflow-reduction device was an orifice plate at the duct inlet, which would pass the jet and entrained fluid but impede the movement of fluid upstream along the wall. Results clearly showed that the performance of ejector-diffuser system was improved for certain a range of system pressure ratios, where as there was no appreciable transition in the performance for lower pressure ratios and the orifice plate was detrimental to the ejector performance for higher pressure ratios. It is found that an appropriately sized orifice system should produce considerable improvement in the ejector-diffuser performance in the intended range of pressure ratios.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.353-356
• /
• 2008

The effects of design parameters of supersonic ejector system under the assumption of constant pressure mixing; such as mass flow rate ratio, area ratio, Primary mach number on ejector system performance were investigated by theoretical formulations. And for a given design condition and working fluid, Computational Fluid Dynamics was conducted.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.413-422
• /
• 2005

In this paper, numerical results for 3-D supersonic turbine flow have been firstly compared with the experimental results to verify results computed by $Fine^{TM}/Turbo$. It was found that $Fine^{TM}/Turbo$ can accurately predict flow characteristics within supersonic turbine. Next, an grid system for 3D turbine flow was optimized selected through grid independency test. Finally the effect of axial gap between rotor and nozzle and chamfer angle of blade edge on the flow characteristics within 3-D supersonic turbine was analyzed with Frozen Rotor method.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.6 no.3
• /
• pp.1-7
• /
• 2002

During the preliminary design phase of aircraft development, it is necessary to evaluate many potential engine/airframe combinations to determine the best solution to given set of mission requirements and it is very important to establish a methodology to calculate precisely engine installed performance. It was carried out to calculate turbofan engine installed performance of a supersonic aircraft for a given engine/aircraft configuration. Thus "Thrust minus drag accounting system" was introduced to identify and calculate the elements of installed thrust or installed propulsive force by using the database based on wind tunnel test data. This paper describes the calculated results of installed thrust of turbofan engine for a supersonic aircraft. aircraft.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.411-414
• /
• 2010

In supersonic propulsion system, the inlet buzz phenomenon in the subcritical operation arises large pressure oscillation, combustion instability, and thrust loss, etc. Inlet Buzz phenomenon and the spray injection/combustion are figured out by the unified unsteady numerical analysis. TAB(Taylor Analogy Breakup) model was applied. Acoustic mode of the entire engine was investigated by detail analysis of pressure fluctuation at each location of the engine.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.384.1-384
• /
• 2002

Rocket propulsion systems generate very high level noise (acoustic loads), which is due to supersonic jet of rocket propulsion system. In practice, the sound power level of rocket propulsion systems is over 180 ㏈. This high level noise excites rocket structures and payloads, so that it causes the structural failure and electronic malfunctioning of payloads. Prediction method of acoustic loads of rocket enables us to determine the safety of payloads. (omitted)

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.05a
• /
• pp.23-26
• /
• 2003

Recently, the thrust vector control using a secondary flow injection which is accomplished by injecting a secondary flow into the supersonic exhaust flow through hole in the wall of the propulsion nozzle has been attention in the applications of the rocket propulsion system. In the present study, 3-dimensional compressible, Navier-Stokes equation to understand the SITVC(Secondary Injection Thrust Vector Control) flow field. The computational results are validated with previous experimental data available. The computational results are visualized detailed structure of shock wave induced by secondary flow and deflected supersonic jets.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.5
• /
• pp.43-53
• /
• 2014

Shock tunnels are known to be capable of simulating flow-field environments of supersonic and hypersonic flights. They have been operated successfully world-wide for almost half a century. As a consequence of the strong interest in hypersonic vehicles in Korea, attention has been given on this type of facility and so an intermediate-sized shock tunnel has lately been built at KAIST. In the light of this, this paper presents our tunnel performance and some of the model scramjet test data. The freestream flow used in this work replicates a supersonic combustor environment for a Mach 5.7 flight speed.