• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.3
• /
• pp.231-236
• /
• 2015

Investigations into cavity flows have been conducted for decades now, most of them being about zero-pressure-gradient flows entering a cavity on a straight wall. However, the flow over curved walls in real-life situations has not been fully investigated. As cavity flows on curved walls exert centrifugal force, these walls are likely to possess different features from straight walls. To verify this possibility, this study investigated cavity flows on curved walls. Using numerical method, the effect of two variables, namely, radius of curvature on a curved wall and inlet Mach number, were investigated for subsonic and supersonic cavity flows. The result demonstrates that the value of the peak pressure generated inside the cavity increases with the decrease in the radius of curvature on a curved wall or an increase in the inlet Mach number. The total pressure loss in the cavity also results in an increase in the cavity drag.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.88-92
• /
• 2009

Total pressure recovery ratio in intake is crucial factor to the operational characteristics of supersonic propulsion system because it does not compress inlet air mechanically by compressor, but does compress inlet air by ram compression. As the result of that the dynamic characteristic analysis of engine was performed before the controller was designed, it could be ascertained when the AoA of flight vehicle increases, the buzz margin decreases so that the shock wave produced outside intake in the specified area according to flight operation's characteristics. Therefore the PID control algorithm was designed to be controlled buzz margin that the characteristic of shock wave could meet the requirement of performance in intake. The PID controller was designed that the buzz margin value is being positive number using the control variables; fuel flow and nozzle throat area.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.5
• /
• pp.31-36
• /
• 2015

As one of the most promising propulsive systems in the future, the dual-mode scramjet engine has drawn the attention of many researches. Detailed flow features concerned with the isolator play an important role in the dual-mode scramjet system. The 2D numerical method has been used for the dual-mode scramjet with wind tunnel. To validate the ability of the numerical model, numerical results have been compared with the experimental results. Overall pressure distributions show quite good match with the experimental results. Back pressure has been studied for maximum pressure rising. According to the results, pressure distribution of supersonic inlet section is not influenced by back pressure. The shock train is pushed towards upstream as the back pressure increases. The maximum value of back pressure without inlet unstart goes up rapidly and then keeps constant when the isolator length increases. The optimal length of isolator section ($L/H_{th}$) is 8.7 in this model.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.1
• /
• pp.97-102
• /
• 2013

A prestudy on expendable turbine engine for high-speed vehicle was conducted. After two possible mission profiles were established to decide the engine requirements, design point analysis was performed with the values of design parameter which were obtained from similar class engines, references, etc. The results showed that specific net thrust and specific fuel consumption with turbine inlet temperature of 3,600 R are 2,599.4 ft/s and 1.483 lb/(lb*h) respectively at the flight condition of sea level, Mach 1.2. It was also found that major design parameters for determining maximum net thrust were turbine inlet temperature for low supersonic and transonic flight speed and compressor exit temperature for high supersonic flight speed from the results of performance analysis on the two possible mission profiles. In addition, simple turbojet engine with an axial compressor, a straight annular combustor, an one stage axial turbine and a fixed throat area converge-diverge exhaust nozzle was proposed as the configuration of simple low cost lightweight turbine engine.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.11
• /
• pp.1067-1074
• /
• 2010

In this study, RBDO(Reliability Based Design Optimization) was performed for a supersonic double-wedge inlet. By considering uncertainty of design with given design space, the pressure recovery was transformed into the probabilistic constraint while the inlet drag was considered as a deterministic objective function. To save computational analysis cost and to search good design space, Latin-Hypercube design of experiment and the Kriging model were incorporated and then RBDO was performed. Monte-Carlo simulation was performed to verify the accuracy of AFORM(Advanced First Order Reliability Method). It was found that AFORM result agreed very well with the Monte-Carlo simulation result. The system reliability was guaranteed by considering uncertainty of the design variables. In case of considering diverse uncertainty of system design, RBDO was found to be useful.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.5
• /
• pp.60-65
• /
• 2011

The development of an air data acquisition algorithm has been described in the supersonic flow at the preliminary design stage with pressure data acquisition device composed of major three total pressure sensors and two static pressure sensors which are installed on the surface of a cone type supersonic inlet. Through this algorithm, Mach number, angle of attack and sideslip angle can be very easily derived with simple interpolation algorithm and predefined data tables. The available range of Mach number is 1.6 to 4.0, angle of attack, $-12^{\circ}$ to $12^{\circ}$ and sideslip angle, $-12^{\circ}$ to $12^{\circ}$. In preliminary design stage, the data tables applied to the developed algorithm are constructed with data driven by Taylor Maccoll equation. The present algorithm would be useful to get supersonic flow air data for the various aerial vehicles and their flight tests.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.6
• /
• pp.9-16
• /
• 2010

The SFRJ(Solid Fuel Ram-Jet) propulsion is attractive for projectiles because of the combination of high propulsive performance and low system complexity more than conventional projectiles. The Objective of this research was to characterize the inlet aerodynamic characteristics (center-body & pitot type) in SFRJ. Diffuser static pressure & combustion chamber pressure was tested and the AoA was changed $0^{\circ}$ and $4^{\circ}$ at Mach number of 3.0 for performance estimate. The performance study of inlet was carried out with the Schlieren system and Supersonic cold-flow system. Under mach 3.0, the center-body showed twice higher total pressure recovering ratio than the pitot type. A Computational fluid dynamic solution is applied internal flow of inlet and the solutions are compared with experimental results.

• New & Renewable Energy
• /
• v.10 no.1
• /
• pp.6-19
• /
• 2014

Organic Rankine cycle (ORC) has been widely used to convert renewable energy such as solar energy, geothermal energy, or waste energy etc., to electric power. For a small scale output power less than 10 kW, turbo-expander is not widely used than positive displacement expander. However, the turbo-expander has merits that it can operate well at off-design points. Usually, the available thermal energy for a small scale ORC is not supplied continuously. So, the mass flowrate should be adjusted in the expander to maintain the cycle. In this study, nozzles was adopted as stator to control the mass flowrate, and radial-type turbine was used as expander. The turbine operated at partial admission. R245fa was adopted as working fluid, and supersonic nozzle was designed to get the supersonic flow at the nozzle exit. When the inlet operating condition of the working fluid was varied corresponding to the fluctuation of the available thermal energy, optimal operating condition was investigated at off-design due to the variation of mass flowrate.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.61-65
• /
• 2011

In this paper, the nozzle design with asymmetric configuration using the optimal method is used in order to improve the under- and over-expansion problem of the flow at the supersonic turbine nozzle. For the design of nozzle contour, 8 design variables are selected and the total-to-static efficiency from the nozzle inlet to the wake outlet is considered as the objective function to be maximized. The Fluent6.3 and the iSIGHT-FD program are used for calculation of nozzle flow and design optimization respectively. RBF(Radial Basis Function) method is chosen for approximate optimization algorithm. It is shown that the static efficiency of improved nozzle design increases 1.35% and loss coefficient decreases 19.85% as compared to baseline design.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.6
• /
• pp.37-46
• /
• 2018

A design study on the cooling channel configuration in a regeneratively cooled supersonic combustor was performed. The flow parameters on the hot- and cold-side channels were calculated using a quasi-one-dimensional model. The heat transfer between these two sides was estimated as a part of the flow calculation. For the reference configuration, the total amount of heat exchanged was 10.7 kW, the heat flux was $566kW/m^2$, and the fuel temperature increase between the inlet and outlet was 153 K. Seven designs of the heat exchanger channel were compared for their heat transfer performance.