• Korean Journal of Materials Research
• /
• v.30 no.8
• /
• pp.435-440
• /
• 2020

The relationship between the precipitation of secondary phase and the thermal properties of Al-4.5%Cu alloy (in wt.%) after various heat treatments has been studied. Solid solution treatment of alloy was performed at 808 K for 6 hours, followed by warm water quenching; then, the samples were aged in air at 473 K for different times. The thermal diffusivity of the Al-4.5%Cu alloy changed with the heat treatment conditions of the alloy at temperatures below 523 K. The as-quenched specimen had the lowest thermal diffusivity, and as the artificial aging time increased, the thermal diffusivity of the specimen increased in the temperature range between 298 and 523 K. For the specimen aged for five hours, the thermal conductivity was 12% higher than that of the as-quenched specimens at 298 K. It is confirmed that the thermal diffusivity and thermal conductivity of the Al-4.5%Cu alloy significantly depend on their thermal history at temperatures below 523 K. The precipitation and dissolution of the Al₂Cu phase were confirmed via DSC for the alloys, and the formation of coefficient of thermal expansion peaks in TMA was caused by precipitation. The precipitation of supersaturated solid solution of Al-4.5%Cu alloys had an additional linear expansion of ≈ 0.05 % at 643 K during thermal expansion measurement.

• Journal of the Korean Society for Heat Treatment
• /
• v.9 no.2
• /
• pp.121-129
• /
• 1996

The solubility of Ti in Al matrix was determined by X-ray diffraction method on two different mechanical alloying systems, i.e Al+$Al_3Ti$ and Al+Ti alloys. Starting powder compositions of two systems were chosen for final volume fraction of $Al_3Ti$ phase being 25%. The solubility of Ti in ${\alpha}$-Al was estimated by the lattice parameter measurement of Al. For Al+$Al_3Ti$ mixture, it appeared that some of $Al_3Ti$ particles decomposed during milling and maximum solubility of Ti in Al was about 0.99%. The majority of $Al_3Ti$ particles were dispersed uniformly in Al matrix, having approximate size of 100~200 nm. On the other hand, higher Ti solubility of 1.24 wt.% was found in Al+Ti system, with starting composition of Al+10 wt.%Ti. After 15 hours of milling, Ti phase was identified as 20 nm sized particles embedded in Al matrix. The annealing of mechanically alloyed powders from Al+$Al_3Ti$ and Al+10 wt.%Ti systems was followed in the temperature range of 200 to $600^{\circ}C$ to study thermal stability of supersaturated solution of Al(Ti). After annealing, the lattice parameter of Al reverted back to that of pure Al, and the peak intensity ratio of $Al_3Ti$/Al was increased more than the original value before annealing. These results suggest that Ti dissolve into alpha-Al solutions during milling, and by annealing, $Do_{22}-Al_3Ti$ phase forms from Al(Ti) solution.

• Restorative Dentistry and Endodontics
• /
• v.22 no.1
• /
• pp.193-208
• /
• 1997

Much evidence now exists from both in vivo and in vitro studies to support the claim that small caries lesions can 'heal'. But, there are still different views on the mechanism of remineralization. So in order to find the best condition for the remineralization of incipient dental caries in maximum efficient way, the author conducted the experiment which reveals the effect of pH on remineralization. 40 specimens of sound permanent teeth without demineralization or crack, $100{\mu}m$ in thickness, were immersed in lactic acid buffered demineralization solution for 4 days. Dental caries with surface zone and subsurface lesion were artificially produced. All specimens were immersed in lactic acid buffered remineralization solution of pH 4.0, 4.5, 5.0, 5.5 containg fluoride ion for 10 days. The results were obtaind by observing the specimens for every 10 days under polarized microscopy at x25. 1. Remineralization did not occur in entire depth of body of lesion at given degree of saturation and concentration of fluoride ion. 2. The pattern of remineralization has increased according to increase of pH. So it can be concluded that supersaturated solution with fluoride ion can be affected by pH in remineralization of enamel, and pH 5.5 seems to be very effective in remineralization of deep and surface zone of dental caries. However, more complex factors exist in achieving complete remineralization and further continuous researches are needed to clarify the factors.

• Journal of Environmental Science International
• /
• v.8 no.6
• /
• pp.711-716
• /
• 1999

This research explored the feasibility of preparing and utilizing a prefonned polymeric solution of Al(III) for coagulation in water treatment. Slow base(NaOH) injection into supersaturated aluminum chloride and aluminum sulfate solutions did produce high yields of Al polymers useful to water treatment applications. The method of characterization analysis was based on timed spectrophotometer with ferron as a color developing reagent. The hydrolytic Al species were divided into $monomeric(Al_a),\;polymeric(Al_b),\;and\;precipitate(Al_c)$ from the difference in reaction kinetics. The analysis of PACl's characteristics showed that the quantity of polymeric Al produced at value of$ r(OH_{added}/AI)=2.2$ was $83\%$ of the total aluminum in solution, as showing maximum contents and precipitated Al was dramatically increased when r was increased above 2.35. In addition, the characteristics of polyaluminum sulfate (PAS) showed that polymeric Al contained at r = 0.75 was $18\%$ of the total aluminum in solution. The synthesized PACI and PAS were stable during storing period, as indicating negligible aging effect. The effect of sulfate ion on PACI was dependent on the concentration of sulfate ion. That is, polymeric species decrease and precipitate species increase as sulfate ion concentration increased. It can be concluded that the sulfate cause the formation of $Al(OH)_{3(S)}$ at low pH. However, The effect of calcium ion was negligible for distribution of Al species.

• Journal of the Korean Society for Heat Treatment
• /
• v.21 no.5
• /
• pp.251-258
• /
• 2008

A transmission electron microscope investigation has been performed on the morphology of dislocations in deformed ${\gamma}^{\prime}-Ni_3(Al,Ti)$ alloys containing fine dispersion of disordered ${\gamma}$ particles. Superlattice dislocations dissociate into fourfold Shockley partial dislocations in a uniform supersaturated solid solution of the ${\gamma}^{\prime}$ phase. Dislocations are attracted into the disordered ${\gamma}$ phase and dissociate further in the particles. At any stage of aging, dislocations cut through the particles and the Orowan bypassing process does not occur even in the over-aged stage of this alloy system. The work necessary to pull the dislocation away from the disordered particles into the ordered matrix should mainly contribute to increase the strength of the ${\gamma}^{\prime}$ phase containing fine dispersion of the disordered ${\gamma}$ phase.

• Journal of the Korean Society for Heat Treatment
• /
• v.9 no.4
• /
• pp.252-260
• /
• 1996

A study was conducted to examine the precipitation phenomena of Al-2.1Li-2.9Cu alloy by differential scanning calorimetry and transmission electron microscopy. DSC curves were measured over the temperature range of $25{\sim}550^{\circ}C$ at a heating rate of $2{\sim}20^{\circ}C$/min.. Three heat evolution peaks and three heat absorption peaks were observed in the DSC curve for the as-quenched specimen. From DSC results and TEM analysis, it was proved that the precipitation sequence in the as-quenched specimen is supersaturated solid solution ${\rightarrow}$ GP zone ${\rightarrow}{\delta}^{\prime}{\rightarrow}T_1{\rightarrow}T_2$ and ${\theta}^{\prime}$ was detected in the peak aged specimen at $160^{\circ}C$. The major phase formed at peak hardeness in the aging at $160^{\circ}C$ was ${\delta}^{\prime}$ phase. The activation energies for the formation of ${\delta}^{\prime}$ and $T_1$ phases were 22.3kcal/mole and 24.3kcal/mole, respectively. These lower activation energies than those for diffusion of Cu and Li in Al are ascribed to the quenched-in excess vacancies.

• Tribology and Lubricants
• /
• v.23 no.1
• /
• pp.14-18
• /
• 2007

SCM415 alloy was implanted with nitrogen ions using plasma source ion implantation (PSII), at a dose range of $1{\times}10^{17}\;to\;6{\times}10^{17}N^{+}cm^{-2}$. Auger electron spectrometry (AES) was used to investigate the depth profile of the implanted layer. Friction and wear tests were carried out on a block-on-ring wear tester. Scanning electron microscopy (SEM) was used to observe the micro-morphology of the worn surface. The results revealed that after being implanted with nitrogen ions, the frictional coefficient of the surface layer decreased, and the wear resistance increased with the nitrogen dose. The tribological mechanism was mainly adhesive, and the adhesive wear tended to become weaker oxidative wear with the increase in the nitrogen dose. The effects were mainly attributed to the formation of a hard nitride precipitate and a supersaturated solid solution of nitrogen in the surface layer.

• International Journal of Precision Engineering and Manufacturing
• /
• v.7 no.4
• /
• pp.47-50
• /
• 2006

SCM415 alloy was implanted with nitrogen ions using plasma source ion implantation (PSII), at a dose range of $1{\times}10^{17}\;to\;6{\times}10^{17}\;N^+cm^{-2}$ Auger electron spectrometry (AES) was used to investigate the depth profile of the implanted layer. Friction and wear tests were carried out on a block-on-ring wear tester. Scanning electron microscopy (SEM) was used to observe the micro-morphology of the worn surface. The results revealed that after being implanted with nitrogen ions, the frictional coefficient of the surface layer decreased, and the wear resistance increased with the nitrogen dose. The tribological mechanism was mainly adhesive, and the adhesive wear tended to become weaker oxidative wear with the increase in the nitrogen dose. The effects were mainly attributed to the formation of a hard nitride precipitate and a supersaturated solid solution of nitrogen in the surface layer.

• Restorative Dentistry and Endodontics
• /
• v.20 no.2
• /
• pp.818-826
• /
• 1995

The present study was undertaken to investigate the crystal growth onto enamel mineral and synthetic hydroxyapatite seeds in media resembling the enamel fluid composition. Effects of fluoride at low concentrations on the precipitation were also examined in a benchtop crystal growth model adopting a miniaturized reaction column. X-ray diffraction and Fourier transform infrared spectroscopy(FTIR), as well as chemical analyses, were employed for characterization of both seed materials before and after experimentation. Remarkable findings were that (1) both biological and synthetic seeds at the same total surface areas yielded rather similar precipitation rates at all levels of fluoride concentration in solution and (2) the precipitation rate was accelerated in a manner depending on fluoride concentrations in media. FTIR differential analysis disclosed that the precipitating phase was characterized as poorly crystallized apatite, which incorporated subtle carbonate. Most of the fluoride ions in soution were readily incorporated into crystals. The overall results support the view that the seeded crystal growth model is of value to gain insight into the mechanism of enamel crystal growth under fluoride regimens.

• Journal of the Korean Society for Heat Treatment
• /
• v.6 no.3
• /
• pp.138-143
• /
• 1993

Effects of aging treatment on the microstructural evolution of a rapidly solidified Al-Li-Cu alloy were investigated by differential scanning calorimetry (DSC) and transmission electron microscopy(TEM). It was found that the precipitation sequence was: supersaturated solid solution ${\alpha}^{\prime}$ ${\rightarrow}$ metastable ${\delta}^{\prime}$ + stable precipitate $T_1$ ${\rightarrow}$ stable precipitates ${\delta}+T_1$. Two exothermic and two endothermic peaks are detected by DSC analysis. The two exothermic and endothermic peaks corresponded to ${\delta}^{\prime}$ and ${\delta}+T_1$ precipitation and dissolution reactions respectively. The enthalpy of ${\delta}^{\prime}$ precipitation decreased with increasing of aging temperature and time until the finishing point of precipitation. The activation energy for precipitation of ${\delta}^{\prime}$ was measured as 80KJ/mol and the energy for dissolution was 93KJ/mol. These values arc higher than those of AI-Li binary alloy. Peak hardness value (Hv 170) was obtamed at $210^{\circ}C$ for 1hr aging treatment which coincided with finishing point of ${\delta}^{\prime}$ precipitation.