• Journal of Environmental Science International
• /
• v.22 no.7
• /
• pp.801-810
• /
• 2013

To improve the physical and chemical properties of the soil and increasing water-retaining property of the soil, Superabsorbent synthetic polymeric materials have been used. The experiment carried out from April to July 2012 after the influence evaluation of Superabsorbent synthetic polymeric materials to vines plant. The result shows that the study of Hedera japonica Tobler, the growth and the survival rates rank as media > hydroponic > superabsorbent synthetic polymers, and the growth and the survival rates are considerably pessimistic in the experiment of hydroponic and superabsorbent synthetic polymers. In the study of Trachelospermum asiaticum var. intermedium, the growth and the survival rates rank as hydroponic > media > superabsorbent synthetic polymers, the difference between the experiment of hydroponic and is very small and the survival rates are not very good in the experiment of superabsorbent synthetic polymers. In the study of Euonymus fortunei var. radicans Rehder,it is insignificantly difference among the different of planting based. Judging from these results, the differences are depending on the species of plants. The thesis holds that the characteristics of plant should be considered in plant cultivation and soil improvement in the future, and it is desirable to use the appropriate mixing ratio of soil in soil improvement as well.

• Magazine of the Korea Institute for Structural Maintenance and Inspection
• /
• v.17 no.3
• /
• pp.92-98
• /
• 2013

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.35 no.12
• /
• pp.157-164
• /
• 2019

Superabsorbent polymers(SAPs) are powdery material that absorb water several tens or hundreds of times its own mass. It has been reported that when SAPs are incorporated into a high strength cementitious material, the autogenous shrinkage of the material is reduced. Cross-linked sodium polyacrylate type SAPs are relatively safe for human body and low in production cost. In order to apply this type of SAPs to the admixture for total(plastic+autogenous+drying) shrinkage reduction of high strength mortar, the shrinkage behavior of mortar when an expansion agent(EA) and SAPs were mixed together was analyzed. As a result, it was found that the shrinkage was reduced when an EA 5% (mass % of cement) and SAPs 0.4% were mixed together than the mortar containing only an EA 10%. The shrinkage was further reduced when EA 10% and SAPs 0.4% were incorporated into mortar.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.58 no.3
• /
• pp.47-56
• /
• 2016

Superabsorbent Polymers (SAPs) are hydrophilic synthetic polymers which could absorb water by hundreds of their own weight. They are used for multiple purpose including hygienic goods, soil conditioners, and hospital supplies. It is necessary to investigate the standard of their use including the amendment rate for soil application in agricultural fields. It is also important to understand their effects on the soil water content and engineering characteristics. The objective of this study is to find the water absorbing capacity and reusability of SAPs, and the characteristics of water release and effect of them on soil water content and engineering characteristics. In the result, SAPs per unit weight (1 g) used for this research could absorb about 200 g of water in max. The water absorbing capacity decreased after SAPs were used repeatedly. Released water of SAPs could provide the soils with about 9 % of the soil water content. Soil water content increased with decreasing distance from the SAPs. The distance of release was spreaded out with increasing water absorbed of SAPs. Finally, when a drainage and the capacity of soil water content were considered, it is recommended to amend the SAPs with soil by less than 0.25 %.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.11
• /
• pp.3163-3172
• /
• 2010

In this work, a novel method to synthesis of an acrylic superabsorbent hydrogel was reported. In the two stage hydrogel synthesis, first copolymerization reaction of acrylonitrile (AN) and acrylamide (AM) monomers using ammonium persulfate (APS) as a free radical initiator was performed. In the second stage, the resulted copolymer was hydrolyzed to produce carboxamide and carboxylate groups followed by in situ crosslinking of the polyacrylonitrile chains. The results from FTIR spectroscopy and the dark red-yellow color change show that the copolymerization, alkaline hydrolysis and crosslinking reactions have been do take place. Scanning electron microscopy (SEM) verifies that the synthesized hydrogels have a porous structure. The results of Brunauer-Emmett-Teller (BET) analysis showed that the average pore diameter of the synthesized hydrogel was 13.9 nm. The synthetic parameters affecting on swelling capacity of the hydrogel, such as AM/AN weight ratio and hydrolysis time and temperature, were systematically optimized to achieve maximum swelling capacity (330 g/g). The swollen gel strength of the synthesized hydrogels was evaluated via viscoelastic measurements. The results indicated that superabsorbent polymers with high water absorbency were accompanied by low gel strength. The swelling of superabsorbent hydrogels was also measured in various solutions with pH values ranging from 1 to 13. Also, the pH reversibility and on-off switching behavior makes the hydrogel as a good candidate for controlled delivery of bioactive agents. Finally, the swelling of synthesized hydrogels with various particle sizes obey second order kinetics.

• Polymer Science and Technology
• /
• v.10 no.2
• /
• pp.215-223
• /
• 1999

• Elastomers and Composites
• /
• v.55 no.4
• /
• pp.249-256
• /
• 2020

Superabsorbent polymers (SAPs) can absorb and retain ten to thousand times their dry mass of water because of their three-dimensional hydrophilic structures. Conventional SAPs are mainly composed of poly(acrylic acid sodium salt) derived from petrochemicals. The present work is aimed at limiting the use of the petrochemical component by replacing it with a biomass-based material. First, the core-SAP was prepared via the terpolymerization of itaconic acid, vinylsulfonic acid, and cellulose, and the optimum conditions in terms of material input ratio were determined. Following this, the core-SAP was surface-crosslinked by esterification with butane diol to improve its liquid permeability and absorbency under load (AUL). The liquid permeability was measured according to the amount of 0.9 wt.% NaCl solution passing between the swollen SAP particles under a given pressure, and the AUL was estimated from the weight of this solution absorbed under 0.3 psi pressure.

• International Journal of Concrete Structures and Materials
• /
• v.8 no.3
• /
• pp.229-238
• /
• 2014

Typical high-performance concrete (HPC) mixtures are characterized by low water-cementitious material ratios, high cement contents, and the incorporation of admixtures. In spite of its superior properties in the hardened state, HPC suffers from many practical difficulties such as its sensitivity to early-age cracking (which is associated with self-desiccation and autogenous shrinkage). In this context, conventional curing procedures are not sufficiently effective to address these limitations. In order to overcome this issue, two strategies,which are based on the use of internal reservoirs of water, have been recently developed.One of these strategies is based on the use of lightweight aggregates (LWA), while the other is based on the use of superabsorbent polymers (SAP). This paper studies and compares the efficiency of the LWA and SAP approaches.Moreover, some of the theoretical aspects that should be taken into account to optimize their application for internal curing of HPC are also discussed. Two fine LWA's and one SAP are studied in terms of autogenous deformation and compressive strength. Increasing the amounts of LWAor SAP can lead to a reduction of the autogenous deformation and compressive strength (especially when adding large amounts). By selecting appropriate materials and controlling their amount, size, and porosity, highly efficient internal water curing can be ensured.

• Polymer(Korea)
• /
• v.28 no.1
• /
• pp.18-23
• /
• 2004

Superabsorbent poly(potassium acrylate-co-acrylamide)s were synthesized in particle form using inverse suspension polymerization technique. Mean diameter of the prepared polymer particles decreased from 300 to 50 $\mu\textrm{m}$ with increasing surfactant concentration. The dynamic and equilibrium swelling behaviors during water absorption and drying process were investigated by weight measurement. The swelling ratio of polymer particles in water changed according to not only polymer crosslinking density, but particle size, saline concentration of aqueous medium, and copolymer compositions. Water sorption amount was increased with decreasing particle size, crosslinking agent concentration, and ion concentration in bulk solution. Being different from the water sorption process, the drying process was not significantly affected by particle size, polymer composition, or crosslinking amount.

• Journal of the Society of Disaster Information
• /
• v.19 no.2
• /
• pp.280-291
• /
• 2023

Purpose: As fire accidents happen at the production and storage sites of superabsorbent polymers for convenience of daily life, an experimental study was conducted to secure basic data to establish practical preventive measures against them. Method: The sample container (20cm width × 20cm length) was made into a rectangular cuboid with the heights of 3cm, 5cm, 7cm, and 14cm, respectively, to allow access to the infinite flat plane. The front and back of the container were covered with a 300-mesh stainless steel mesh for one-dimensional heat transfer. The sample container was placed in the center of the thermostatic bath, which was heated to a predetermined temperature by setting the thermostat program in advance, and it was determined to be 'ignited' when the central temperature of the sample rose by more than 20℃ above the set temperature, and "unignited" when it was maintained at an approximate value of the set temperature. Result: The critical autoignition temperature was calculated to be 217.5℃ when the height of the sample container was 3 cm, 212.5℃ when it was 5 cm, 202.5℃ when it was 7cm, and 187.5℃ when it was 14cm. The ignition induction time to reach the maximum temperature was 34hours for 3cm, 76hours for 5cm, 143hours for 7cm, and 318hours for 14cm. Conclusion: ① As the size of the container increased, the autoignition temperature decreased and the induction time to reach the maximum temperature increased. ② An apparent activation energy was calculated to be 44.92kcal/mol, with a correlation of 96.93%.