• Journal of Environmental Health Sciences
• /
• v.29 no.2
• /
• pp.1-6
• /
• 2003

This paper reports on a pilot scale comparison of PACS coagulation with and without pH preadjustment. The pH of the water was adjusted with carbon dioxide and sulfuric acid. Process performance was assessed on the basis of total organic carbon(TOC), UV absorbance, turbidity and disinfection by-product(DBP) precursors. Coagulation pH appeared to be a determining factor for maximum NOM removal. The optimum coagulation pH in order to decrease TOC and turbidity were pH 7. Preadjustment of pH 7 increased TOC removal to as much as 43, 47 percent with sulfuric acid and carbon dioxide. Moreover, coagulation at pH 7 caused a reduction in UV$_{254}$, THMFP and HAAFP compared to the baseline coagulation. For preadjustment of pH 7 with carbon dioxide, the percentage of TOC, UV$_{254}$, THMFP and HAAFP shows the reduction rate of 3.8, 0.5, 4.8, 9.4％ comparing to the coagulation rendition using sulfuric acid. Acid addition to depress pH during coagulation decrease Langelier Saturation Index(LSI), potentially causing increase corrosion in water distribution systems. LSI for carbon dioxide and sulfuric acid at pH 6 was -2.3, -3.3. Therefore, carbon dioxide was more effective at controlling corrosion than sulfuric acid.

• Composite Materials and Engineering
• /
• v.3 no.3
• /
• pp.167-178
• /
• 2021

In the present paper, the destructive behavior of distilled water, salty water, sulfuric acid, and heat on glass/vinyl ester composites was investigated by experimental methods. Hetron 922 vinyl ester resin and two types of mat and woven glass fibers as the reinforcements were used to fabricate composite test samples. All samples were immersed in distilled water, salty water, and sulfuric acid with three different concentrations. The tests were performed at 20℃ and 70℃ for the exposure duration of 1, 2, 4, and 8 weeks. Bending tests were performed after aging for all composite samples to check the degradation of the bending modulus and strength. The results show that the effect of distilled water, in comparison with salty water, on the degradation of composite samples was significant. On the other hand, almost non-sensitivity of concentrations of salty water on the weight gain of specimens has been observed. In addition, it was also observed that the degradation of samples at 70℃ temperature is much more than that of at 20℃. Also, it was observed that the flexural modulus of virgin specimens exposed to salty water (2% concentration) has been recovered just after two weeks of immersion. Furthermore, in some cases, composite samples under the sulfuric acid solution have lost almost 80% of their mechanical properties.

• Korean Membrane Journal
• /
• v.7 no.1
• /
• pp.28-33
• /
• 2005

The feasibility of producing sulfuric acid and ammonia water from ammonium sulfate was investigated by an integrated process including ammonia stripping (AS) and electrodialysis with bipolar membrane (EDBM). It was suggested that the production of sulfuric acid using ammonia stripping-electrodialysis with bipolar membrane (ASEDBM) was effective in obtaining high concentration of sulfuric acid compared with EDBM alone. AS was carried out over pH 11 and within the range of temperatures, $20^{\circ}C{\~}60^{\circ}C$. Sodium sulfate obtained using AS was used as the feed solution of EDBM. The recovery of ammonia increased from $40\%$ to $80\%$ at $60^{\circ}C$ due to the increased mobility of ammonium ion. A pilot-scale EDBM system, which is composed of two compartments and 10 cell pairs with an effective membrane area of $200 cm^2$ per cell, was used for the recovery of sulfuric acid. The performance was examined in the range of 0.1 M${\~}$1.0 M concentration of concentrate compartment and of $25 mA/cm^2{\~}62.5 mA/cm^2$ of current density. The maximum current efficiency of $64.9\%$ was obtained at 0.1 M sulfuric acid because the diffusion rate at the anion exchange membrane decreased as the sulfuric acid of the concentrate compartment decreased. It was possible to obtain the 2.5 M of sulfuric acid in the $62.5 mA/cm^2$ with a power consumption of 13.0 kWh/ton, while the concentration of sulfuric acid was proportional to the current density below the limiting current density (LCD). Thus, the integrating process of AS-EDBM enables to recover sulfuric acid from the wastewaters containing ammonium sulfate.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.7 no.4
• /
• pp.600-610
• /
• 1995

When combustion gas is cooled down below the dew point of sulfuric acid vapor in the heat recovery systems, condensation occurs. Since the condensed sulfuric acid solution causes low-temperature corrosion in materials, it is important to measure the SOx dew point by electric measurement. In this study, two kinds of probes having electric gaps of 1mm or 2mm were used. and experiments were carried out by the parameters of sulfuric acid vapor and water vapor concentration. The changes of electric current caused by sulfuric acid condensed on the surface of probe according to the cooling rate and the probe head surface temperature were sudied. The opimum cooling rate was decreased with the increasing of water vaper concentration regardless of sulfuric acid concentration. The sensitivity of electric current is improved for the narrower gap(1mm) of ring electrodes, but it rarely affects the SOx dew point measuring of different probes according to the change of cooling rate.

• Asian Journal of Atmospheric Environment
• /
• v.4 no.1
• /
• pp.55-61
• /
• 2010

The sensitivity of aerosol light extinction coefficient to the aerosol chemical composition change is estimated by (1) calculating the aerosol water content and chemical concentrations by a gas/particle equilibrium model and (2) calculating the aerosol light extinction coefficient by a Mie theory based optical model. The major chemical species are total (gas and particle phase) sulfuric acid, total nitric acid, and total ammonia which are based on the measurement data at Seoul and Gosan. At Seoul, since there were enough ammonia to neutralize both total sulfuric acid and total nitric acid, the dry ionic concentration is most sensitive to the variation of the total nitric acid level, while the total mass concentration (ionic concentration plus water content) and thus, the aerosol light extinction coefficient are primarily determined by the total sulfuric acid. At Gosan, since the concentration of ambient sulfuric acid was the highest among the inorganic species, sulfate salts determined aerosol hygroscopicity. Thus, both ionic and total mass concentration, and resultant aerosol light extinction coefficient are primarily determined by the sulfuric acid level.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.11
• /
• pp.2059-2065
• /
• 2000

The purpose of this study is to improve coagulation efficiency by pre-treatment of high pH water using sulfuric acid. The common reason of pH increasing at down stream of Nakdong river is water blooming. The pH go above 9.0 during water blooming periods. The higher pH water demands more coagulant and pre-chlorine dosage than lower pH water for better coagulation condition. The DOC, THMFP, UV-254 after coagulation with the same coagulant dosage by pre-treatment from pH 9.2 down to 8.1 with sulfuric acid are 1.84mg/L, $51{\mu}g/L$ and $0.032cm^{-1}$, by pretreatment of chlorine are 2.09mg/L, $78{\mu}g/L$ and $0.030cm^{-1}$, by pre-treatment of sulfuric acid and chlorine are 2.14mg/L, $72{\mu}g/L$ and $0.031cm^{-1}$ respectively. Pretreatment with sulfuric acid can improve water quality and reduce coagulant demand.

• Textile Coloration and Finishing
• /
• v.7 no.2
• /
• pp.9-16
• /
• 1995

When alkaline waste water of PET fabric is treated with sulfuric acid, undegradable material, crude TPA sludge is generated, so that treatment has a serious problem. The result of DMT synthesis using crude TPA sludge generated from PET alkaline waste water were as follows: 1. When crude TPA generated from alkaline waste water is reactioned with methanol under catalyst of sulfuric acid, pure DMT can be obtained. 2. In DMT synthesis from crude TPA, addition of copper sulfate can increase yield, and increasing the amount of sulfuric acid can shorten reaction time.

• Journal of Environmental Science International
• /
• v.12 no.6
• /
• pp.659-664
• /
• 2003

The experiment was carried out to investigate the effects of sulfuric acid and nitric acid among the main components of simulated acid rain (SAR) on the growth of vegetative organs and seed germination of Arabidopsis thaliana. The Arabidopsis treated with SAR supplemented with sulfuric and nitric acids, respectively, showed 28% and 30% decrease of shoot and root growth compared to the control plants, and also many necrotic spots on leaf surfaces after SAR treatment were observed. The shoot and root length for plants grown with nitric acid rain was 14% and 17% lower, respectively, compared to the control, whereas those grown with sulfuric acid rain was 24% and 25% lower than control plants. When Arabidopsis seeds were sown in distilled water, germination rate was 100% after 7 days. However, 80% in SAR medium supplemented with sulfuric and nitric acids, 88% in sulfuric acid rain medium and 93% in nitric acid rain medium. The germination abilities of seeds harvested from SAR supplemented with sulfuric and nitric acids, sulfuric acid rain, and nitric acid rain were 73%, 73% and 94%, respectively. Consequently, sulfuric acids showed more inhibitory effects than nitric acids on the growth of vegetative organs as well as germination rates in Arabidopsis.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.11a
• /
• pp.151-152
• /
• 2019

This study is aimed at comparing the effect of cement mortar made of sulfuric acid treated ISO standard sand with that of cement mortar made of normal ISO standard sand. In the water absorption test, water absorption of standard sand increases with the increase of immersion time in sulfuric acid solution. The results show that at the water cement ratio of 0.5, the longer the standard sand is immersed in sulfuric acid, the greater the compressive strength of the cement mortar sample.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.1
• /
• pp.36-42
• /
• 2005

This study examined the feasibility of producing sulfuric acid and ammonia water from ammonium sulfate solution using two-compartment electrodialysis with a bipolar membrane (EDBM). Electrodialysis experiments were carried out with 20 wt% ammonium sulfate at different current densities and sulfuric acid concentrations in a concentrate compartment. The current efficiency increased with the current density from 25 to $100\;mA/cm^2$. Nevertheless, the efficiency was relatively low compared with that of general desalting electrodialysis, owing to the diffusion of sulfuric acid from the concentrate compartment to the diluate. The diffusion rate through the anion exchange membrane increased with the sulfuric acid concentration in the concentrate compartment, which decreased the current efficiency. Conversely, the electrical resistance decreased with increasing current density owing to the Joulian heat generated during water dissociation in the transition region of the bipolar membrane under a high electric field. From the experimental results, we concluded that operating at a higher current density is effective from the perspective of current efficiency and electrical resistance when producing sulfuric acid and ammonia water from ammonium sulfate using a two-compartment EDBM process. Further studies on the effects of increasing the sulfuric acid concentration on current efficiency are required to apply the EDBM process practically.