• 대한기계학회논문집B
• /
• 제20권5호
• /
• pp.1689-1699
• /
• 1996

A study on the transitional boundary layer with arbitrary pressure gradient under various upstream conditions is very important for engineering applications like the performance predictions of the turbomachineries under various and strong disturbances. Experimental data on the transitional boundary layer for real cascades of the turbomachinery are rare because of difficulties in boundary layer experiments. Flow on NACA0012 airfoil is more similar to the real case than that on the flat plate with which many researches are done. The data of the transitional flow on the airfoil could be used to verify or to develop a turbulence model for numerical simulations. The experiment was performed with two cases of Reynolds number at a=0$^{0}$ and one case of Reynolds number at a=5$^{0}$ . The measured data are the transition length and the wall shear stresses. These two characteristic values are measured within 25%~90% of the airfoil chord by Computation Preston tube Method(CPM) proposed by Nitsche et al.(1983). At a=0$^{0}$ , transition occured at 70% and 55% of chord length when R $e_{c}$=6*10$^{5}$ and 8* 10$^{5}$ , respectively. It started when R {\theta}=500 regardless of R $e_{c}$, and ended when R {\theta}=750, and 850 respectively. The transition length was 15~20% of the chord length. At a=5$^{0}$ (R $e_{c}$=6*10$^{5}$ ), boundary layer on the pressure side does not undergo transition, but on the suction side transition occured at .chi.$_{c}$/c=0.16 and ended at .chi.$_{c}$/c=0.22.c//c=0.22./c=0.22.c//c=0.22.

• 대한기계학회논문집B
• /
• 제40권5호
• /
• pp.321-327
• /
• 2016

본 연구에서는 고속 회전을 하는 진공청소기용 원심홴의 공력성능 향상을 위해 에어포일 임펠러(Airfoil Impeller)의 적용을 검토 및 연구하였다. 에어포일 최대두께 및 최대두께 위치에 따라 3종의 에어포일 임펠러를 제시하였고, 이때 C4 에어포일 두께분포를 이용하였다. 에어포일 임펠러의 성능 평가는 전산유체역학(Computational Fluid Dynamics) 해석과 흡입일률시험을 통해 수행되었다. 이를 통해 에어포일 형상 적용 시 기존 블레이드 형상에 비하여 임펠러 블레이드 압력면과 디퓨져 블레이드 압력면에서 발생하는 유동박리가 크게 줄어드는 것을 확인하였다. 그리고 이로 인해 기존 원심홴에 비하여 홴 효율이 약 3% 증가 및 비소음이 약 1.3dB(A) 감소되는 것을 확인하였다.

• 한국유체기계학회 논문집
• /
• 제8권4호
• /
• pp.27-38
• /
• 2005

The present study investigated the effect of relative position of the blade on blade surface heat transfer. The experiments were conducted in a low speed wind tunnel with a stationary annular turbine cascade. The test section has a single turbine stage composed of sixteen guide vanes and blades. The chord length of the blade is 150 mm and the mean tip clearance of the blade is $2.5\%$ of the blade chord. The Reynolds number based on blade inlet velocity and chord length is $1.5{\times}105$ and mean turbulence intensity is about $3\%$. To investigate the effect of relative position of blade, the blade at six different positions in a pitch was examined. For the detailed mass transfer measurements, a naphthalene sublimation technique was used. In general, complex heat transfer characteristics are observed on the blade surface due to various flow characteristics, such as a laminar flow separation, relaminarization, flow acceleration, transition to turbulence and tip leakage vortices. The results show that the blade relative position affects those heat transfer characteristics because the distributions of incoming flow velocity and turbulence intensity are changed. Especially, the heat transfer pattern on the near-tip region is significantly affected by the relative position of the blade because the effect of tip leakage vortex is strongly dependent on the blade position. On the pressure side, the effect of blade position is not so significant as on the suction side surface although the position and the size of the separation bubble are changed.

• 한국항공우주학회지
• /
• 제30권1호
• /
• pp.1-8
• /
• 2002

자유류 속도가 40 m/sec 이고 날개의 뿌리시위에 기준한 레이놀즈수가 1.76${\times}$10$^6$인 상태에서 옆미끄럼이 삼각 날개 와류에 미치는 영향을 실험적으로 연구하였다. 받음각 범위는 16$^{\circ}$에서부터 28$^{\circ}$까지 이었으며 옆미끄럼각은 0$^{\circ}$, -10$^{\circ}$, 그리고 -20$^{\circ}$이었다. 옆미끄럼각은 바람쪽과 바람 반대쪽 와류 모두의 강도를 감소시키고, 바람쪽 와류의 붕괴를 촉진시킴이 관찰되었다. 옆미끄럼각 -10$^{\circ}$에서 바람 반대쪽의 와류는 받음각이 증가함에 따라 그 강도가 증가하였다. 이와 같은 옆미끄럼 조건에서 날개 와류의 비대칭적인 발달과 붕괴는 삼각 날개의 롤링모멘트를 어느 특정한 높은 받음각에서 급격히 바뀌게 할 수 있으며, 이는 일종의 롤링 모멘트 불안정성으로 간주할 수 있다.

• Wind and Structures
• /
• 제20권1호
• /
• pp.37-58
• /
• 2015

As wind flows around a sharp-edged body, the resulting separated flow becomes complicated, with multiple separations and reattachments as well as vortex recirculation. This widespread and unpredictable phenomenon has long been studied academically as well as in engineering applications. In this study, the flow characteristics around rectangular prisms with five different aspect ratios were determined through wind tunnel experiments and a detached eddy simulation, that placed the objects in a simulated deep turbulent boundary layer at $Re=4.6{\times}10^4$. A series of rectangular prisms with the same height (h = 80 mm), different longitudinal lengths (l = 0.5h, h, and 2h), or different transverse widths (w = 0.5h, h, and 2h) were employed to observe the effects of the aspect ratio. Furthermore, five wind directions ($0^{\circ}$, $10^{\circ}$, $20^{\circ}$, $30^{\circ}$, and $45^{\circ}$) were selected to observe the effects of the wind direction. The simulated results of the surface pressure were compared to the wind tunnel experiment results and the existing results of previous papers. The vortex and spectrum were also analyzed to determine the detailed flow structure around the body. The paper also highlights the pressure distribution around the rectangular prisms with respect to the different aspect ratios. With an increasing transverse width, the surface suction pressure on the top and side surfaces becomes stronger. In addition, depending on the wind direction, the pressure coefficient experiences a large variation and can even change from a negative to a positive value on the side surface of the cube model.

• 대한조선학회논문집
• /
• 제60권4호
• /
• pp.231-239
• /
• 2023

In order to improve the propeller Cavitation Inception Speed (CIS) performance, it needs to modify the propeller geometry and the wake distribution that flows into the propeller. In the previous study, the twisted angles of the V-strut were modified to improve propeller CIS, cavitation behavior and pressure fluctuation performances. Then the propeller behind the modified V-strut (New strut) showed better cavitation characteristics than that behind the existing V-strut (Old strut). However, the CIS of Suction Side Tip Vortex (SSTV) and Pressure Side Tp Vortex (PSTV) showed a big difference at behind each V-strut. In this study, the balance design is conducted to minimize the difference between SSTV CIS and PSTV CIS at behind each V-strut. To improve the propeller CIS performance, 1 propeller is designed at behind the old strut and 3 propellers are designed at behind the new strut. The propeller CIS is increased through the balance design and the stern appendage modification. The final propeller CIS is increased about 5.3 knots higher than that of the existing propeller at behind the old strut. On the basis of the present study, it is thought that the better improvement method for the propeller CIS would be suggested.

• 대한기계학회논문집B
• /
• 제26권9호
• /
• pp.1249-1259
• /
• 2002

The present study investigates the convective heat/mass transfer inside a cooling passage of rotating gas-turbine blades. The rotating duct has various configurations made of ribs with 70。 attack angle, which are attached on leading and trailing surfaces. A naphthalene sublimation technique is employed to determine detailed local heat transfer coefficients using the heat and mass transfer analogy. The present experiments employ two-surface heating conditions in the rotating duct because the surfaces, exposed to hot gas stream, are pressure and suction side surfaces in the middle passages of an actual gas-turbine blade. In the stationary conditions, the parallel rib arrangement presents higher heat/mass transfer characteristics in the first pass, however, these characteristics disappear in the second pass due to the turning effects. In the rotating conditions, the cross rib present less heat/mass transfer discrepancy between the leading and the trailing surfaces in the first pass. In the second pass, the heat/mass transfer characteristics are much more complex due to the combined effects of the angled ribs, the sharp fuming and the rotation.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2002년도 유체기계 연구개발 발표회 논문집
• /
• pp.258-263
• /
• 2002

A numerical analysis using 2-D unsteady compressible program is conducted to explain characteristics of rotating stall such as rotating speed and number of stall cells in an one-stage axial compressor. Unlike an axial compressor which has only a rotor, in one-stage axial compressor a rotating stall is generated by rotor/stator interaction and tack pressure rising without any artificial disturbance and modeling. As a back pressure is raised, the separation of suction side at blades is increased uniformly, but because of the discrepancy of blockage effect by stator, the disturbances are generated to form a stall cell. Once the stall cell is formed, regularly the stall cell are rotating through rotor blades. When the speed of rotor is design speed the rotating speed of stall cell is $83.3\%$ of rotor rotating speed. When the speed of rotor is $80\%$ of design speed, the speed of rotating stall is $88.2\%$ of rotor speed. The number of generated stall cell are also varied for rotor speed and back pressure.

• 대한기계학회논문집B
• /
• 제28권8호
• /
• pp.902-909
• /
• 2004

A steady-state Reynolds averaged Navier-Stokes simulation was conducted to investigate the distribution of the Reynolds stress tensor inside tip leakage vortex of a linear compressor cascade. Two different inlet flow angles ${\beta}=29.3^{\circ}$(design condition) and $36.5^{\circ}$(off-design condition) at a constant tip clearance size of $1\%$ blade span were considered. Classical methods of solid mechanics, applied to view the Reynolds stress tensor in the principal direction system, clearly showed that the high anisotropic feature of turbulent flow field was dominant at the outer part of tip leakage vortex near the suction side of the blade and endwall flow separation region, whereas a nearly isotropic turbulence was found at the center of tip leakage vortex. There was no significant difference in the anisotropy of the Reynolds normal stresses inside tip leakage vortex between the design and off-design condition.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.1686-1691
• /
• 2004

The effect of recirculated exhaust gas on performance and exhaust emissions with FGR rate are investigated by using a natural circulation, pressurized draft and water tube boiler with FGR system operating at several boiler loads and over fire air(OFA) damper openings. The purpose of this study is to apply the FGR system to a power plant boiler for reducing $NO_{x}$ emissions. To activate the combustion, the suction damper of two stage combustion system installed in the upper side of wind box is opened by handling the lever between $0^{\circ}$ and $90^{\circ}$ , and the OFA with 0 to 20% into the flame is supplied, as the combustion air supplied to burner is reduced. It is found that the fuel consumption rate divided by evaporation rate does not show an obvious tendency to increase or decrease with rising the FOR rate, and $NO_{x}$ emissions are decreased, at the same OF A damper opening, as FOR rates are elevated and boiler loads are dropped.