• 한국지능시스템학회논문지
• /
• 제24권5호
• /
• pp.512-517
• /
• 2014

본 연구는 선박의 외벽 유지보수를 위한 외벽 연마장비에 장착되는 먼지 집진장치에 적용하기 위한 사이클론 집진방식의 연마기 제작을 위한 사이클론 분리기 설계를 위하여 최적의 설계조건을 도출하고자 유동해석 기법을 적용한 사이클론 연마장비의 집진장치를 소개하고자 한다. 제작된 연마장비의 집진을 위한 접선유입 사이클론의 압력 강하와 입자 수집 능률은 기 연구된 수학적 모델을 적용하여 계산하였다. 종래 공기필터를 가진 사이클론의 계산 결과의 비교는 접선 유입 사이클론이 저압 드롭과 높은 입자 수집능률을 시뮬레이션을 통한 검증과 시작품을 제시하였다. 사이클론은 원통형 장치 내에 분진을 함유하는 기체를 장치내벽에 접선방향으로 유입시켜 유입분진에 선회운동을 부여함으로써 분진입자에 작용하는 원심력에 의하여 가스중의 입자를 분리 포집하는 집진장치로써 연마장비의 집진장치로 응용하고자 본 연구를 진행하여 진행중인 메커니즘과 유체흐름에 대한 기본적인 유체흐름에 따른 사이클론의 규격 파라미터에 따른 유동해석 결과를 제시하였다.

• 한국생산제조학회지
• /
• 제20권6호
• /
• pp.805-810
• /
• 2011

Recently, Use of Auxiliary power unit(APU) is increasing by growing demand for improvement of insufficient electric power and installation of emergency generation devices in military tracked vehicles and civil markets. And the trend is that the units are demanded for smaller size, lighter weight and higher output power, etc to suit consumer demands. To achieve these, it is essential to develop high performance system. Therefore, in this study, it was conducted in numerical analysis to investigate flow characteristics of rotor in APU generator. Also output performance of APU applied on the rotor is analyzed by experimental method. As the result, higher rotating speed of rotor caused high air flow rate at suction and it leads to linear increase of discharging flow rate. The maximum theoretical power was achieved at 12 $m^3$/min of flow rate and, at that time, output power of generator was about 7.825 kW. Also, it can be confirmed the stabilization of output performance is achieved in about 2 seconds by experiment.

• 설비공학논문집
• /
• 제29권3호
• /
• pp.127-133
• /
• 2017

Performance analysis has been carried out on a high side scroll compressor that had a fixed scroll equipped with a circular oil groove on its thrust surface. Oil was supplied to the oil groove through an intermittent opening from a high pressure oil reservoir formed inside the orbiting scroll hub. Oil in the groove was then delivered to both suction and back pressure chambers by pressure differentials and viscous pumping action of the orbiting scroll base plate. Mathematical modeling of this oil groove system was incorporated into a main compressor performance simulation program for an optimum oil groove design. The study findings were as follows. Pressure in the oil groove can be controlled by changing its configuration and the oil passage area. With an enlarged oil passage, the pressure in the oil groove heightens due to an increased flow rate, but the pressure elevation in the back pressure chamber is small, resulting in reduced friction loss at the thrust surface between the two scrolls. On the other hand, by increasing the oil passage area, the oil content in the refrigerant flow increases. Considering all these factors, the energy efficiency ratio could be improved by about 3.6% under the ARI condition by an optimal oil groove design.

• 한국자동차공학회논문집
• /
• 제14권1호
• /
• pp.92-99
• /
• 2006

The swirl ratio of a charge in the cylinder was estimated by calculating the ratio of the rotary speed of charge which could be simulated from the rotary speed of paddle in the swirl measurement apparatus, to the engine speed which could be calculated by measuring intake air flow rate. The automation of the swirl ratio measurement for cylinder head was achieved by controling both valve lift in cylinder head and a suction pressure of surge tank using two step-motors. The number of measurement position for calculating mean swirl ratio was varied by adjusting the interval of valve lift. The mean swirl ratio with varying the number of measurement position showed nearly constant value. Two measurement methods for measuring the swirl ratio were compared, one was to control the suction pressure of the surge tank with PID (proportional, integral, differential) mode with by-pass valve controlled by the step motor and the other did not control the surge tank pressure by fixing the by-pass valve. The difference of the mean swirl ratio between the two measurement methods showed nearly constant value with varying the number of measurement position. This means that the w/o PID control method could be preferred to the PID control method which has been used, due to the simpleness of the swirl measurement.

• 멤브레인
• /
• 제31권5호
• /
• pp.343-350
• /
• 2021

본 연구에서는 다공성 중공사형 분리막(multi-bore capillary membrane module)을 생물막 반응기(MBR)에 침지시켜 운전시간에 따른 흡입 압력을 측정하였다. 공칭 세공크기가 0.2㎛, 외경이 6.4 또는 4.2 mm이고 육각 형태인 중공사형모듈을 MLSS 8,000 mg/L 활성 슬러지 수용액에 각각 침지시키고 투과 유속, 공기량에 따른 변화를 확인하였다. 여과운전/정지이완(FR) 및 정지이완 시 역세척(FR/BW) 및 사인파형 투과유속 연속운전(SFCO) 방식으로 조작하였다. SFCO의 흡입 압력은 30 L/m²·hr에서 낮았으며, 50 L/m²·hr에서는 FR의 흡입 압력이 높게 나타났다. 또한 외경이 작은 모듈의 흡입 압력 상승이 비교적 낮았으며, 외경이 큰 모듈의 흡입 압력은 높게 상승하였지만 역세척으로 40% 이상 감소시킬 수 있었다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권6호
• /
• pp.665-671
• /
• 2007

The purpose of this study is to find out a flow characteristics required by the design of a computer case and to provide information about the preliminary data of cooling efficiency of CPU and a flow inside of a case. We examined a flow characteristic-suction a tracing particle occurred from a surge tand installed at an inlet into a computer case and moving it to a exit duct-experimentally by using PIV. The experimental device was consists of a fan inflowing and discharging the air into the computer case and a slot installed with a CPU cooling ran add-on, and analyzed the data of Re-stress distribution, velocity distribution, and kinetic energy distribution. This research will make a great contribution to improvement of the efficiency and performance of notebook, workstation, server, and all the design of electronic devices using large scale integrated(LSI) as well as usual computers.

• 지질공학
• /
• 제20권3호
• /
• pp.281-295
• /
• 2010

새롭게 구축된 자동 흙-함수특성곡선 시험장치는 측정원리가 간단하고 연속적인 측정이 가능하며, 시험자에 의해 발생될 수 있는 오차를 최소화하여 보다 정확한 불포화토의 흙-함수특성곡선을 산정할 수 있다. 본 시험장치는 압력조절장치, 플로우셀, 물저장소, 공기방울트랩, 저울, 시료준비장치, 측정시스템 등으로 구성되어 있다. 공기의 압력은 0-300 kPa범위까지 적용할 수 있으며, 단기간내 시험을 완료할 수 있다. 본 시험장치에서는 건조과정과 습윤과정을 재현할 수 있으며, 측정 자동화 프로그램(SWRC)을 이용하여 건조과정과 습윤과정에 따른 시료내 함수비 변화를 실시간으로 확인할 수 있다. 본 시험기를 이용하여 상대밀도 75%인 주문진 표준사에 대한 건조 및 습윤과정의 체적함수비에 따른 모관흡수력을 측정하였다. 측정결과, 건조 및 습윤과정을 거치는 동안 동일한 체적함수비에서 대한 모관흡수력 값이 다르게 나타나는 이력현상(hysteresis)이 발생하였다. 측정된 결과를 토대로 기존의 Brooks and Corey, van Genuchten 및 Fredlund and Xing 방법을 이용하여 흙-함수특성곡선을 예측하였다. 결정계수를 이용하여 이들 방법에 대한 정확성을 평가한 결과 대상토질조건의 경우 van Genuchten방법이 신뢰성이 가장 높은 것으로 나타났다.

• 유기물자원화
• /
• 제21권3호
• /
• pp.74-81
• /
• 2013

본 연구는 생활폐기물 처리에서 매립되는 폐기물량을 줄이고 재활용비율을 늘리기 위하여 고안된 풍력선별기 (공기의 흐르는 방향을 이용하여 공기 중에서 비중분리를 수행하는 방법)에 대하여 ANSYS사의 CFX Program을 이용한 수치 해석적 방법을 통해 풍력선별기의 모형을 설계 및 제작하고 시뮬레이션을 통해 풍력에 따른 폐기물의 분리 효율을 고찰하였다. 흡입장치에서 비닐봉지 1000mL를 흡입하도록 설계할 때 입구 풍속은 0.9 m/sec 이상에서 100%효율을 얻을 수 있었고 1.6 m/sec 이상에서 의 플라스틱병 500mL 와 플라스틱병 1500mL의 혼합 폐기물 효율의 100 % 알루미늄 250mL 선별 효율은 2.3 m/sec 이상에서 100% 마지막으로 알루미늄 250mL를 5mm 두께 압축 선별 효율은 2.4 m/sec 이상에서 90% 임을 알 수 있었다.

• Environmental Engineering Research
• /
• 제25권2호
• /
• pp.251-257
• /
• 2020

This study was performed to verify the possibility of nitrification and denitrification in a single reactor. In batch type experiment, optimal point of experimental conditions could be found by performing the experiments. When supply location of microbubbles was located at half of width of the aeration tank and operating pressure of 0.5 bar, it was possible for zones in the aeration tank to be separated into anoxic and aerobic by controlling air suction rate according to operating pressure of the generator. To be specific, the concentration of dissolved oxygen (DO) in zone 1 and 2 of the aeration tank could be maintained as less than 0.5 mg/L. Also, in the case of concentration of oxygen in zone 3 and 4, the concentration of DO was increased up to 1.7 mg/L due to effects of microbubbles. In continuous flow type experiment based on the results of batch type experiments, the removal efficiency of nitrogen based on T-N was observed as 39.83% at operating pressure of 0.5 bar and 46.51% at operating pressure of 1 bar so it was able to know that sufficient air suction rate should be required for nitrification. Also, denitrification process could be achieved in a single reactor by using ejector type microbubble generator and organic matter and suspended solid could be removed. Therefore, it was possible to verify that zones could be separated into anoxic and aerobic and nitrification and denitrification process could be performed in a single reactor.

• 설비공학논문집
• /
• 제19권12호
• /
• pp.842-849
• /
• 2007

For a $CO_2$ two-stage twin rotary compressor used for heat pump water heater system, changes of $CO_2$ solubility in PAG oil were investigated along the gas passages from the first stage suction to final discharge. Only slight changes in solubility took place in suction chambers for both of the first and second stages, but for compression chambers, solubility variation ranged from 0.115 to 0.136, and from 0.133 to 0.182, respectively for the first and second stages. Calculation of gas flashing in parts of leakage oil flows and of oil contained in control volumes due to solubility changes was conducted and included in gas pressure calculation. For the second stage, gas flashing amounts to around $5%\sim6%$ for most leakage flows. Cooling capacity, compressor input, and COP obtained by calculation were well compared to the experimental results. Effects of operation speed on the compressor performance was also studied: as the shaft speed increased, adiabatic efficiency decreased rapidly due to increased over-compression loss.