• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권10호
• /
• pp.559-563
• /
• 2000

The $(Sr_{1-x}Ca_x)TiO_3(SCT)$ thin films are deposited on Pt-coated(Pt/TiN/$SiO_2$/Si) using RF sputtering method with substitutional contents of Ca. The maximum grain of thin films is obtained by substitution of Ca at 15[mol%]. Also the composition of SCT thin films were closed to stoichiometry(1.081∼1.117 in A/B/ ratio). The dielectric constant was increased with increasing the substitutional contents of Ca, while it was decreased if the substitutional contents of Ca exceeded over 15[mol%]. The dielectric constant changes almost linearly in temperature ranges of -80∼+90[^${\circ}C$]. The temperature properties of the dielectric loss have a stable value within 0.02 independent of the substitutional contents of Ca. All SCT thin films used in this study show the phenomena of dielectric relaxation with the increase of frequency, and the relaxation frequency is observed above 2000[kHz]. The current-voltage characteristics of SCT15 thin films showed the increasing leakage current as the measuring temperature increase.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.294-294
• /
• 2007

Spinel cathode material $LiMn_2O_4$ is currently studied as a promising cathode material for lithium ion secondary batteries for future applications because of it is low cost, easy to be prepared and capable to be operated in high voltage range. However as a cathode material, $LiMn_2O_4$ performs a poor capacity retention which leads to short cycle life. In this study, stoichiometric $LiMn_2O_4$ was synthesized with granulation method with ion substitution to stabilize its structure and niobium doping to improve its conductivity. These well-mixed powders were calcined at $850^{\circ}C$ for 6 hours and its properties were investigated. Correlations of dopant and electrochemical properties were examined as well.

• Bulletin of the Korean Chemical Society
• /
• 제13권2호
• /
• pp.131-135
• /
• 1992

High-Tc superconducting materials, $HoBa_2Cu_3O_{7-x}F_y$ with $0.0{\leq}y{\leq}0.5$, were synthesized by ceramic method and studied by X-ray diffraction, thermogravimetric analysis, differential thermal analysis, scanning electron microscopy and resistivity measurement. From the X-ray diffraction data, it was found that the samples had only single phase of which lattice volumes were decreased in proportional to the amount of fluorine, which indicated that the relatively small fluorine atoms are effectively substituted for the oxygen sites. Also, an anomalous phenomenon appeared that the peak intensities of (001) planes were greatly increased as fluorine contents increased. SEM photographs revealed that the grain sizes were enlarged progressively with fluorine contents. This fact could be explained along with DTA & TGA data that the incorporation of fluorine gave rise to lowering the melting point. Tc decreased as the incorporation of fluorine content increased. This implies that the superconducting electrons are perturbed due to the substitution of electronegative fluorine atom.

• Bulletin of the Korean Chemical Society
• /
• 제20권1호
• /
• pp.42-48
• /
• 1999

We have performed a quantum-chemical investigation on the conformations and electronic properties of a variety of methoxy-substituted poly(p-phenylenevinylenes) (PPVs) to elucidate the effects of alkoxy substitution. Geometrical parameters for the polymers were fully optimized through Austin Model I (AM I) semi-empirical Hartree-Fock (HF) band calculations. Electronic properties of the polymers were obtained by applying the AM I optimized structures to the modified extended Huckel method. To confirm validity of the AM I conformational results, we also carried out ab initio HF calculations with the 6-31G (d) basis set for a variety of methoxy-substituted divinylbenzenes. It is found that the potential energy surfaces of alkoxy-substituted PPVs are quite shallow around the planar conformations, suggesting that the prepared films possess a variety of conformations with different torsion angle in the solid state, depending on the synthetic conditions. When two alkoxy groups are concurrently substituted at the adjacent sites in the phenylene ring, these groups are subject to rotating around the C(sp2)-O bonds by 70-80° to avoid the strong steric repulsion between them. Consequently, the overlap between the π-type p orbital of oxygen and the π molecular orbitals of the polymer decreases. This leads to a wide gap and a high oxidation potential for tetramethoxy-substituted PPV, compared to those of dialkoxy-substituted PPV.

• 한국환경과학회지
• /
• 제32권6호
• /
• pp.477-482
• /
• 2023

Halloysite nanotube (HNT) has a nanotube structure with the chemical formula of Al₂Si₂O₅(OH)₄ · nH₂O and is a natural sediment of aluminosilicate. A lot of research has been conducted to improve the mechanical properties of epoxy composites by generating interactions between HNTs and polymers through surface treatment of HNTs, such as exchange of amine group as a terminal functional group. However, most of the surface modification methods are performed under wet conditions, which require a relatively large amount of time, manpower and solvent. In order to save time and simplify complicated procedures, a dry coating machine was designed and used for amine group exchange. Comparing the XPS results, it was found that the results of NH₂-HNT prepared using a dry coating machine and the substitution through the wet method were not significantly different, and it has been confirmed that the amount of solvent used and the time savings can be made.

• 응용통계연구
• /
• 제25권6호
• /
• pp.877-887
• /
• 2012

The Bank of Korea changed its method of GDP estimation from a fixed-weighted to a chain-weighted measure in 2009. The fixed-weighted method had had problems such as substitution bias and the rewriting of economic history. As a result of the change, annual growth rates calculated using the chain-weighted method from 1970 through 2008 turned out to be 0.8%p higher on average than the existing rates. The quarterly average chain-weighted growth rates were 0.19%p higher than the fixed-weighted ones, but they changed in the same directions. In this paper we analyze whether the differences in rates between the two calculation methods would bring about a difference in the cyclical characteristics of GDP. We conclude that although there were differences in growth rates after introduction of the chain-weighted method, there was no difference in the cyclical fluctuation.

• Asian-Australasian Journal of Animal Sciences
• /
• 제18권7호
• /
• pp.942-948
• /
• 2005

New polymorphism of major histocompatibility complex B-G genes was investigated by amplification and digestion of a 401bp fragment including intron 1 and exon 2 using polymerase chain reaction-restriction fragment length polymorphism (PCR-RFLP) technique with two restriction enzymes of Msp I and Tas I in eight breeds of Chinese indigenous chickens and one exotic breed. In the fragment region of the gene, three novel single nucleotide polymorphisms (SNPs) were detected at the two restriction sites. We found the transition of two nucleotides of A294G and T295C occurred at Tas I restriction site, and consequently led to a non-synonymous substitution of asparagine into serine at position 54 within the deduced amino acid sequence of immunoglobulin variable-region-like domain encoded by the exon 2 of B-G gene. It was observed at rare frequency that a single mutation of A294G occurring at the site, also caused an identical substitution of amino acid, asparagine 54-to-serine, to that we described previously. And the transversion of G319C at Msp I site led to a non-synonymous substitution, glutamine 62-to-histidine. The new alleles and allele frequencies identified by the PCR-RFLP method with the two enzymes were characterized, of which the allele A and B frequencies at Msp I and Tas I loci were given disequilibrium distribution either in the eight Chinese local breeds or in the exotic breed. By comparison, allele A at Msp I locus tended to be dominant, while, the allele B at Tas I locus tended to be dominant in all of the breeds analyzed. In Tibetan chickens, the preliminary association analysis revealed that no significant difference was observed between the different genotypes identified at the Msp I and Tas I loci and the laying performance traits, respectively.

• 한국광물학회지
• /
• 제14권2호
• /
• pp.128-136
• /
• 2001

흘란다이트 터널 구조내의 A자리 양이온인 $Ba^{2+}$ 이온을 $K^{+ }$ 이온이 치환하면서 결정의 구조에 어떠한 변화가 있는지 알아보기 위해 K-Ba 전구간 완전고용체로 치환된 7개의 합성 흘란다이트형 광물($K_{2x}$ $Ba_{1}$ -x/$Cr_2$$Ti_{6}$ $O_{16}$ , x=0, 0.1, 0.3, 0.5, 0.7, 0.9, 1.0)에 대하여 X선 회절분석과 리트벨트 구조분석법을 실시하였다. 리트벨트 계산 결과, 구조의 정밀도를 나타내는 R 지수값을 보면$ R_{exp}$에 대한 $R_{wp}$ 값($R_{wp}$ /$R_{exp}$ )은 15.77%/20.90%~14.74%/l9.37%의 범위를 보여주며, $R_{B}$ 값은 6.45~8.97%, S (GofF)값은 1.45~l.63으로 각각 계산되었다. 합성 홀란다이트는 K-Ba 전구간에서 Ba의 함량에 관계없이 모두 공간군 14/m을 가지며, 단위포의 크기는 a=10.1194(2) ~ 10.0599(2)$\AA$, c=2.9572(6)~2.9512(7)$\AA$, V=302.75~298.66$\AA^{3}$의 범위를 보여주며, K 함량이 50% 이상에서는 금홍석이 부산물로 합성되었다. 그 결과 A자리의 Ba와 K의 치환관계에서는 비록 단위포의 크기에 일정한 변화를 보여주었으나 구조적 변이에 영향을 주기에는 충분치 않은 것으로 밝혀졌다. 따라서 정방정계에서 대칭성이 낮은 단사정계로의 구조적 변이는 A자리에 대한 K-Ba 치환보다는 다른 양이온의 치환이나 B자리의 치환 등 다른 요인에 의할 것으로 생각된다.다.

• 한국진공학회지
• /
• 제16권4호
• /
• pp.262-266
• /
• 2007

Mn 치환이 역스피넬 산화물 $Fe_3O_4$에 미치는 영향을 조사하기 위하여 졸겔 스핀코팅 방법을 이용하여 다결정 $Mn_xFe_{3-x}O_4$ 박막을 Si(100) 기판 위에 제작하고 그 구조적, 자기적, 자기저항특성들에 대한측정 및 분석을 수행하였다. X-선 회절 측정 결과, Mn 성분비가 증가함에 따라 x = 1.78까지 입방 구조를 유지하며, 그 격자상수는 증가함을 나타내었다. 이와 같은 격자상수 증가의 주된 원인으로 사면체 자리를 선호하는 $Mn^{2+}$ 이온이 이온반경이 상대적으로 작은 사면체 자리의 $Fe^{3+}$ 이온을 치환함에 의한 것으로 해석된다. 박막들에 대한 진동시료자화 측정 결과, Mn 성분비 증가에 따라 포화자화량은 큰 변화를 나타내지 않았는데, Mn과 Fe 이온들의 스핀 자기능률 값 비교를 통하여 그 정성적인 설명이 가능하다. 반면 Mn의 농도가 증가함에 따라 보자력은 감소하였는데, 이는 $Mn^{2+}$ 치환에 의한 $Fe^{2+}$ 이온 농도의 감소에 따르는 자기 이방성의 감소에 기인하는 것으로 해석된다. 자기저항 효과측정 결과, Mn 성분비 증가에 따라 감소하는 경향을 보였으며, 자화 의존도 변화와 비교분석 결과 다결정 $Mn_xFe_{3-x}O_4$ 박막 시료들에서 나타나는 자기저항은 스핀분극된 carrier의 grain boundary tunneling 및 spin-flip 현상에 의한 것으로 해석된다.

• 전기화학회지
• /
• 제8권2호
• /
• pp.82-87
• /
• 2005

고전압 용 양극산화물 $LiNi_{0.5}Mn_{1.5}O_4$는 고온에서 합성 시, 입자 내에 산소결함에 의한 불순물상을 만들게 된다. 불순물상은 불완전한 스피넬 구조를 형성하며 리튬이온의 삽입$\cdot$탈리를 방해하여 전극의 성능을 감소시킨다. 본 연구에서는 고온 열처리 시 생성되는 이러한 불순물상의 거동을 파악하기 위해 크롬을 치환한 $LiNi_{0.5-x}Mn_{1.5}Cr_xO_4(0{\leq}x{\leq}0.05)$를 졸$\cdot$겔법을 이용하여 합성하여 고온 열분석을 실시하였다. 열분석 결과 크롬이 치환되지 않은 양극활물질은 산소결함에 의한 $2\%$의 무게 감소를 보였으나, 크롬이 치환된 경우 무게 감소분이 줄어들어 불순물 생성이 억제됨을 알 수 있었다. XRD 분석에서도 크롬이 치환된 경우 불순물 상이 억제됨을 나타내었으며 불순물상의 감소로 인해 크롬을 첨가한 양극활물질 $LiNi_{0.5-x}Mn_{1.5}Cr_xO_4$를 사용한 경우 충·방전 실험 시 가역 용량과 싸이클 안정성이 향상됨을 볼 수 있었다.