• Journal of Welding and Joining
• /
• 제20권5호
• /
• pp.99-105
• /
• 2002

One of the important advantage of adhesive bonded joint can combine the different materials. The joint that bonded by structural adhesive bond must keep a large force and its strength is affected by some environmental factors such as temperature and submergence time in water. In order to advance the fatigue strength of adhesive bonded joint, mostly put a surface treatment on the surface. This study was researched the effect of air temperature, submergence time, submergence temperature and surface treatment on the fatigue strength. We found that submergence temperature has the most effect and low plasma treatment specimens have the most fatigue strength.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제11권1호
• /
• pp.274-284
• /
• 2019

The control architectures of Chuan Suo (CS) deep submergence rescue vehicle are introduced. The hardware and software architectures are also discussed. The hardware part adopts a distributed control system composed of surface and underwater nodes. A computer is used as a surface control machine. Underwater equipment is based on a multi-board-embedded industrial computer with PC104 BUS, which contains IO, A/D, D/A, eight-channel serial, and power boards. The hardware and software parts complete data transmission through optical fibers. The software part involves an IPC of embedded Vxworks real-time operating system, upon which the operation of I/O, A/D, and D/A boards and serial ports is based on; this setup improves the real-time manipulation. The information flow is controlled by the software part, and the thrust distribution is introduced. A submergence vehicle heeling control method based on ballast water tank regulation is introduced to meet the special heeling requirements of the submergence rescue vehicle during docking. Finally, the feasibility and reliability of the entire system are verified by a pool test.

• 설비공학논문집
• /
• 제19권4호
• /
• pp.313-320
• /
• 2007

In this paper, the experimental study has been carried out to investigate the reliability lifetime of two bearing units based on the oil temperature. Measurements for the oil temperature as well as the bearing temperature during normal operation were performed to study the effects of oil viscosity and oil submergence percentages in the two bearing units. The optimal lubrication condition to increase the lifetime of the bearing unit A was found that its viscosity and submergence percentage were VG32 and 25%, respectively. For the bearing unit B, when the oil viscosity and submergence percent were VG32 and 75%, the lubrication condition was the most efficient. Finally, the adjusted rating times of both the bearing units were calculated to be over 28,000 h, which is greater than the minimum adjusted rating times of 25,000 h. Therefore, they satisfied the regulated lifetime of API 610.

• 대한환경공학회지
• /
• 제34권11호
• /
• pp.772-779
• /
• 2012

본 연구에서는 원뿔형으로 개발된 미세기포형 산기관의 성능향상을 위하여 운용적 측면에서 실험과 전산모사적 방법을 이용하였다. 산기관 잠김깊이의 변화에 대해 성능실험이 용이한 실증 규모의 타워형 생물반응기에 산기관을 장착하여, 잠김깊이가 표준산소전달계수($K_{L}a_{20}$) 및 표준산소전달효율(SOTE) 등 산소전달 성능에 미치는 영향을 실험적으로 연구하였다. 또한, 2상 유동에 관한 유체역학적 전산모사를 이용하여 산기관 수와 잠김깊이에 대한 유동현상을 파악함으로써 산소전달 성능변화에 대한 원인을 규명하였다. 산소전달 성능실험결과, 산기관의 잠김깊이를 6 m에서 12 m로 증가시킴에 따라 표준산소 전달계수는 7% 증가하였으나 표준산소전달효율은 39~72% (5.6 %/m)로 대폭 상승하였다. 유동 해석결과, 산기관의 수가 증가함에 따라 공기 체적분율 및 공기와 시험수의 유속 모두 증가하였으며, 공기와 시험수의 유속 경향은 유사하게 나타났다. 잠김깊이가 증가함에 따라서 공기 체적분율, 공기 및 시험수의 유속은 조금씩 감소하는 경향을 나타냈다. 선회 병류유동은 기포류의 확산과 상승속도를 결정하는 주요 인자로서 선회강도가 과도하게 큰 경우에는 기포 체류시간과 체류량이 감소되므로 산소전달 성능을 저하를 예측할 수 있었다.

• 한국식품저장유통학회지
• /
• 제6권3호
• /
• pp.292-296
• /
• 1999

땅콩의 착협비대기인 '98. 8. 5 - 8. 6 사이 2일간 207 mm에 달하는 집중호우에 의거 침수피해가 발생된 지역에서 약 1개월 후 시료를 채취하여 땅콩의 생육, 수량 및 품질변화에 대하여 조사한 결과, 주경장, 분지장, 생체중 등 지상부 생육과 종실수량은 침수일수가 길수록 현저히 감소되었고, 침수기간이 1일 정도 짧아도 침수기간 3일과 큰 차이없이 피해가 컸으며 땅콩종실의 저장기간중 지질의 산패율은 침수일수가 길수록 산패가 빨랐고, 불포화지방산인 Linoleic acid 조성비도 낮아 품질이 다소 저하되는 경향이었다. 침수일수에 따른 식물체의 지상부 무기성분은 질소, 인산 및 고토의 함량은 침수일수가 길수록 증가되었으나 칼리함량은 감소되었다. 침수피해지의 토양 분석결과 토양중 유기물, 인산 등 각종양분의 함량이 현저히 적어 무침수지에 비하여 양분용탈 및 유실이 심하여 비옥도가 크게 떨어졌다. 따라서 홍수에 의한 침수일수가 길수록 땅콩식물체의 무기성분함량. 품질 및 토양 비옥도에 크게 영향을 미침을 알 수 있었다.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2003년도 추계학술대회 논문집
• /
• pp.213-219
• /
• 2003

As the 2-D hydraulic experimental results for the submerged rubble-mound structure, we have concerned with their stability/function characteristics of structures by the effects of wave force, scour/deposition at the toe and wave transmission ratio at the lee-side sea. And as to investigate the variation characteristics of wave transmission ratio which depended to a geometrical structure of the submerged breakwater profiles, the critical conditions for the depth of submergence and crest width obviously presented. In summary, there results lead us to the conclusions that the wave control capabilities of submerged breakwaters by the variation of the submergence depth is high about 4 time degrees at the efficiency than the that of crest width. The destruction of covering block at the crest generated at the region which located between maximum damage curve, it maximum damage/failure station from the toe of the structure were 0.2L. As the wave transmission coefficient and the slope of the structure increase, the damage/failure ratio and the maximum scour depth at the toe was extended, respectively. When maximum scour depth happened. The destruction of covering block which located at the toe generated at the front slope destruction. Finally, it was found from the results that the optimization of structure may be obtained by the efficiently decision of the submergence depth and crest width in the permissible range of wave transmission ratio.

• Ocean Systems Engineering
• /
• 제5권2호
• /
• pp.109-123
• /
• 2015

In the present study, the coupled dynamic response of a Submerged Floating Tunnel (SFT) and mooring lines under regular waves is solved by using two independent numerical simulation methods, OrcaFlex and CHARM3D, in time domain. Variations of Buoyancy to Weight Ratio (BWR), wave steepness/period, and water/submergence depth are considered as design and environmental parameters in the study. Two different mooring-line configurations, vertical and inclined, are studied to find an optimum design in terms of limiting tunnel motions and minimizing mooring-line tension. The numerical results are successfully validated by direct comparison against published experimental data. The results show that tunnel motions and tether tensions grow with wave height and period and decrease with submergence depth. The inclined mooring system is more effective in restricting tunnel motions compared to the vertical mooring system. Overall, the present study demonstrates the feasibility of this type of structure as an alternative to traditional bridges or under-seabed tunnels.

• 에너지공학
• /
• 제7권2호
• /
• pp.202-208
• /
• 1998

원자력 발전소의 증기방출계통에는 상당수의 산업공정에서 보여지는 바와 같이 배관을 통해 응축성 기체를 침수 분사시켜 응축시키는 과정이 포함된다. 본 연구에서는 증기방출계통 파이프와 지지문의 설계에 사용되는 동적 하중을 계산하기 위하여 증기방출 과도현상에 대한 해석을 특성기법을 사용하여 수행하였다. 해석모델은 마찰이 존재하는 균일한 배관을 통해 증기가 수조로 방출되는 경우에 대하여, 증기유량 및 배관 내에 원래 존재하고 있는 공기와 물의 방출유량 등을 고려하였고 압력 및 열원, 밸브, 분지관 등을 포함하였다. 배관의 유동 특성과 동적 하중을 계통 압력, 배관 길이 및 침수 깊이의 변화에 따라 계산하였다. 계산 결과 공기와 물의 경계에서의 배관의 동적 하중, 배관 내의 물 제거 시간 및 물 이동 속도 등은 계통 압력뿐만 아니라 배관 길이 및 침수 깊이의 영향을 받는 것으로 확인되었다.

• 한국응용곤충학회지
• /
• 제34권1호
• /
• pp.75-81
• /
• 1995

시설 과채류 재배지의 뿌리혹선충의 피해경감을 위해서 경북도내 시설 오이 재배단지인 칠곡과 참외재배 주산지인 성주에서 1992년부터 1994년까지 3년간 방제시험한 결과 뿌리혹선충의 피해를 경감시키기 위한 토양개량 적기는 모래산흙인 마사토의 경우에 3년 붉은산흙인 경우 4년마다 하는 것이 효과적이고 농약과 조합한 오이의 방재시험에서 빗사마드 분제가 78.2%, 카보입제+토양반전+담수가 71.2%, 카보입제+담수가 66.3%이었으며 참외에서 살충제처리후 20일에는 77.7~80.6%의 방제효과를 보였으나 60일 후에는 33.7~49.5%로 방제가 낮아 후기에는 효과가 낮았다. 참외재배 논에서의 작부체계에 따른 뿌리혹선충 밀도 억제효과는 참외 재배후 담수하여 벼를 재배할 때에 벼 수확시 방제효과가 91.1%로 대부분의 선충이 사멸되었다. 각 처리구 공히 처리당시에는 뿌리혹선충 증식을 억제하였으나 생육추기로 갈수록 선충밀도가 증가되었다. 그러나 토양개량은 3년간 효과적이였으며 가장 경제적으로 선충의 증식을 억제하 수 있는 처리는 3년마다 한번씩 벼를 재배하는 것이었다.

• 한국해양공학회지
• /
• 제27권3호
• /
• pp.8-14
• /
• 2013

Although there are various factors that threaten the security of ships, one of the most harmful is corrosion. It is not easy to find corroding areas and the status of corrosion, even though corrosion causes serious problems such as submergence and marine pollution as a result of leaking oil and polluted water. To monitor the corrosion of ships, non-destructive inspection, weight loss coupons, electrical resistance, linear polarization resistance, zero resistance ammeter, and electrochemical impedance spectroscopy have been developed. However, these methods require much time to detect corrosion, and most are not appropriate for real time monitoring. Coating, sacrificial anode, and impressed current cathodic protection (ICCP) methods have been developed to control corrosion. The ICCP and sacrificial anode methods are the most popular ways to prevent ship corrosion. However, ICCP is only appropriate for the outside of a ship and cannot be used for complex structures such as ballast tanks because these are composed of many separate chambers. Sacrificial anodes have to be replaced periodically. This paper proposes an integrated corrosion monitoring and control system (ICMCS) that can detect corrosion in real time and is appropriate for complex structures such as ballast tanks. Because the system uses titanium for an anode, exhausted anodes do not need to be replaced.