• Current Photovoltaic Research
• /
• 제8권2호
• /
• pp.45-49
• /
• 2020

Molybdenum (Mo) thin films are widely used as back contact in copper indium diselenide (CISe) solar cells. However, despite this, there are only few published studies on the properties of Mo and characteristics of CISe solar cells formed on such Mo substrates. In this studies, we investigated the properties of sputter deposited Mo bilayer, and fabricated non-vacuum CISe solar cells using bilayer Mo substrates. The changes in surface morphology and electrical resistivity were traced by varying the gas pressure during deposition of the bottom Mo layer. In porous surface structure, it was confirmed that the electrical resistivity of Mo bilayer was increased as the amount of oxygen bonded to the Mo atoms increased. The resulting solar cell characteristics vary as the bottom Mo layer deposition pressure, and the maximum solar cell efficiency was achieved when the bottom layer was deposited at 7 mTorr with a thickness of 100 nm and the top layer deposited at 3 mTorr with a thickness of 400 nm.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 추계 학술발표회
• /
• pp.1142-1150
• /
• 2010

An elementary particle of bottom ash is similar to fine sand. So which expected from replace expensive sand. Therefore, this study conducts cyclic triaxial test and a resonant test using relative density, which is obtained from a relative density test of bottom ash and standard sand. Also, it compares antiseismic characteristics of bottom ash and standard sand in order to analyze the possibility of commercial use as a construction material.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 춘계 학술발표회
• /
• pp.774-781
• /
• 2009

The purpose of this study was to research on compressibility characteristics of waste tire powder-added lightweight soil(TLS) for recycling dredged soil, bottom ash and waste tire. The TLS used in this experiment consists of dredged soil, cement, waste tire powder and bottom ash. Test specimens were prepared with various content of waste tire powder ranged from 0% to 100% at 25% intervals by the dried weight of dredged soil. Several series of one-dimensional consolidation tests were carried out. Based on the experimental results, as the waste tire powder increased, the swelling index of TLS increased. The compression index and swelling index of the TLS with bottom ash content showed lower value than without bottom ash. Then, compressibility characteristics of TLS were strongly influenced by mixing conditions of waste tire powder content and bottom ash content.

• 한국기계가공학회지
• /
• 제19권4호
• /
• pp.58-64
• /
• 2020

Large-scale flooding due to extreme weather and typhoons causes heavy damage. This is especially true in urban areas where accumulated debris prevents the smooth drainage of rainwater in sewage facilities such as rain gutters installed near roads. In this study, to improve the drainage performance and effectively remove foreign substances by applying the dust screen used in rivers, the rain gutter with Coanda effect was simulated and compared with the experiment. The simulation was performed by setting the parameters to the fillet radius R₁ and R₂ at the top of the screen filter, the fillet radius R₃ at the bottom of the screen filter, and the height H of the gap W from the bottom. W is the gap at the backside of screen filter which is applied to stimulate the Coanda effect. According to the simulation results, the highest drain performance was 87.99% derived from R₁= 30mm, R₂= 5mm, R₃= 85mm, H= 75mm, and W= 2mm. The error rate of simulation results refer to the 4.89%~7.36% compared to the experimental results. In the future, by considering the slope according to the installation environment, the simulation results can be applied to the actual roadside to help prevent flood damage.

• Current Photovoltaic Research
• /
• 제8권1호
• /
• pp.6-11
• /
• 2020

The power conversion efficiency (PCE) of a two-terminal tandem solar cell depends upon the tunnel-recombination junction (TRJ) between the top and bottom sub-cells. An optimized TRJ in a tandem cell helps improve its open-circuit voltage (V_oc), short-circuit current density (J_sc), fill factor (FF), and efficiency (PCE). One of the parameters that affect the TRJ is the buffer layer thickness. Therefore, we investigated various TRJs by varying the thickness of the buffer or intermediate layer (TRJ-buffer) in between the highly doped p-type and n-type layers of the TRJ. The TRJ-buffer layer was p-type nc-Si:H, with a doping of 0.06%, an activation energy (E_a) of 43 meV, an optical gap (E_g) of 2.04 eV, and its thickness was varied from 0 nm to 125 nm. The tandem solar cells we investigated were a combination of a heterojunction with intrinsic thin layer (HIT) bottom sub-cell and an a-Si:H (amorphous silicon) top sub-cell. The initial cell efficiency without the TRJ buffer was 7.65% while with an optimized buffer layer, its efficiency improved to 11.74%, i.e., an improvement in efficiency by a factor of 1.53.

• 한국전기전자재료학회논문지
• /
• 제33권1호
• /
• pp.25-30
• /
• 2020

Oxide (SiO₂)/Metal(Ag)/Oxide(SiO₂, ITO, ZnO) multilayer films were fabricated using a magnetron sputtering technique at room temperature on Si (p-type, 100) and a glass substrate. The electrical and optical properties of the asymmetric multilayer films depended on the thickness of the mid-layer film and the type of oxide in the bottom layer. As the metal layer becomes thicker, the sheet resistance decreases. However, the transmittance decreases when the metal layer exceeds a threshold thickness of approximately 10~12 nm. In addition, the sheet resistance and transmittance change according to the type of oxide in the bottom layer. If the oxide has a large resistivity, the overall sheet resistance increases. In addition, the anti-reflection effect changes according to the refractive index of the oxide material. The optical and electrical properties of multilayer films were investigated using an ultraviolet visible (UV-Vis) spectrophotometer and a 4-point probe, respectively. The optimum structure is SiO₂ (30 nm)/Ag (10 nm)/ZnO (30 nm) multilayer, with the highest FOM value of 7.7×10^-3 Ω^-1.

• 한국환경과학회지
• /
• 제29권7호
• /
• pp.729-737
• /
• 2020

This study estimates the greenhouse gas (GHG) emissions reduction resulting from photovoltaic and wind power technologies using a bottom-up approach for an indirect emission source (scope 2) in South Korea. To estimate GHG reductions from photovoltaic and wind power activities under standard operating conditions, methodologies are derived from the 2006 IPCC guidelines for national GHG inventories and the guidelines for local government greenhouse inventories of Korea published in 2016. Indirect emission factors for electricity are obtained from the 2011 Korea Power Exchange. The total annual GHG reduction from photovoltaic power (23,000 tons CO_2eq) and wind power (30,000 tons CO_2eq) was estimated to be 53,000 tons CO_2eq. The estimation of individual GHGs showed that the largest component is carbon dioxide, accounting for up to 99% of the total GHG. The results of estimation from photovoltaic and wind power were 63.60% and 80.22% of installed capacity, respectively. The annual average GHG reductions from photovoltaic and wind power per year per unit installed capacity (MW) were estimated as 549 tons CO_2eq/yr·MW and 647 tons CO_2eq/yr·MW, respectively. Finally, the results showed that the level of GHG reduction per year per installed capacity of photovoltaic and wind power is 62% and 42% compared to the CDM project, respectively.

• Progress in Superconductivity
• /
• 제10권2호
• /
• pp.99-102
• /
• 2009

We report our development of the fabrication process of sub-micron scale $Al-AlO_x-Al$ tunnel junction by using electron-beam lithography and double-angle shadow evaporation technique. We used double-layer resist to construct a suspended bridge structure, and double-angle electron-beam evaporation to form a sub-micron scale overlapped junction. We adopted an e-beam insensitive resist as a bottom sacrificing layer. Tunnel barrier was formed by oxidation of the bottom aluminum layer between the bottom and top electrode deposition, which was done in a separate load-lock chamber. The junction resistance is designed and controlled to be 50 $\Omega$ to match the impedance of the transmission line. The junctions will be used in the broadband shot noise thermometry experiment, which will serve as a link between the electrical unit and the thermodynamic unit.

• 한국재료학회지
• /
• 제20권2호
• /
• pp.72-77
• /
• 2010

Glass-ceramics were fabricated by heat-treatment of glass obtained by melting a coal bottom ash with $Li_2O$ addition. The main crystal grown in the glass-ceramics, containing 10 wt% $Li_2O$, was $\beta$-spodumene solid solution, while in $Li_2O$ 20 wt% specimen was mullite, identified using XRD. The activation energy and Avrami constant for crystallization were calculated and showed that bulk crystallization behavior will be predominant, and this expectation agreed with the microstructural observations. The crystal phase grown in $Li_2O$ 10 wt% glass-ceramics had a dendrite-like shaped whereas the shape was flake-like in the 20 wt% case. The thermal expansion coefficient of the $Li_2O$ 10 wt% glass-ceramics was lower than that of the glass having the same composition, owing to the formation of a $\beta$-spodumene phase. For example, the thermal expansion coefficient of $Li_2O$ 10 wt% glass-ceramics was $20\times10^{-7}$, which is enough for application in various heat-resistance fields. But above 20 wt% $Li_2O$, the thermal coefficient expansion of glass-ceramics, on the contrary, was higher than that of the same composition glass, due to formation of mullite.

• Current Photovoltaic Research
• /
• 제2권1호
• /
• pp.36-39
• /
• 2014

Formation mechanism of residual carbon layer, frequently observed in the $CuInSe_2$ (CIS) thin film prepared by direct solution coating routes, was investigated in order to find a way to eliminate it. As a model system, a methanol solution with dissolved Cu and In salts, whose viscosity was adjusted by adding ethylcellulose (EC), was chosen. It was found that a double layer, a top metal ion-derived film and bottom EC-derived layer, formed during an air drying step presumably due to different solubility between metal salts and EC in methanol. Consequently, the top metal ion-derived film acts as a barrier layer inhibiting further thermal decomposition of underlying EC, resulting a formation of bottom carbon residue layer.