• Wind and Structures
• /
• v.35 no.1
• /
• pp.21-34
• /
• 2022

Gust factor is an important parameter for the conversion between peak gust wind and mean wind speed used for the structural design and wind-related hazard mitigation. The gust factor of typhoon wind is observed to show a significant dispersion and some differences with large-scale weather systems, e.g., monsoons and extratropical cyclones. In this study, insitu measurement data captured by 13 meteorological towers during a strong typhoon Morakot are collected to investigate the statistical characteristics, height and wind speed dependency of the gust factor. Onshore off-sea and off-land winds are comparatively studied, respectively to characterize the underlying terrain effects on the gust factor. The theoretical method of peak factor based on Gaussian assumption is then introduced to compare the gust factor profiles observed in this study and given in some building codes and standards. The results show that the probability distributions of gust factor for both off-sea winds and off-land winds can be well described using the generalized extreme value (GEV) distribution model. Compared with the off-land winds, the off-sea gust factors are relatively smaller, and the probability distribution is more leptokurtic with longer tails. With the increase of height, especially for off-sea winds, the probability distributions of gust factor are more peaked and right-tailed. The scatters of gust factor decrease with the mean wind speed and height. AS/NZ's suggestions are nearly parallel with the measured gust factor profiles below 80m, while the fitting curve of off-sea data below 120m is more similar to AIJ, ASCE and EU.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.28 no.2
• /
• pp.143-149
• /
• 2022

PCS needs to freely switch AC and DC to connect the battery, external AC loads and renewable energy in both directions for energy efficiency. Whenever converting happens, power loss inevitably occurs. Minimization of the power loss to save electricity and convert it for usage is a very critical function in PCS. PCS plays an important role in the ESS(Energy Storage System) but the importance of stabilizing semiconductors on PCB(Printed Circuit Board) should be empathized with a risk of failure such as a fire explosion. In this study, the temperature variation inside PCS was reviewed by cooling fan on top of PCS, and the vibration characteristics of PCS were analyzed during truck transportation for reliability of the product. In most cases, a cooling fan is mounted to control the inner temperature at the upper part of the PCS and components generating the heat placed on the internal aluminum cooling plate to apply the primary cooling and the secondary cooling system with inlet fans for the external air. Results of CFD showed slightly lack of circulating capacity but simulated temperatures were durable for components. The resonance points of PCS were various due to the complexity of components. Although they were less than 40 Hz which mostly occurs breakage, it was analyzed that the vibration displacement in the resonance frequency band was very insufficient. As a result of random-vibration simulation, the lower part was analyzed as the stress-concentrated point but no breakage was shown. The steel sheet could be stable for now, but for long-term domestic transportation, structural coupling may occur due to accumulation of fatigue strength. After the test completed, output voltage of the product had lost so that extra packaging such as bubble wrap should be considered.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.16 no.2
• /
• pp.97-103
• /
• 2023

Since most of the information is transmitted through the network, eavesdropping and interception by a third party may occur. Appropriate measures are required for effective, secure and confidential communication in the network. Steganography is a technology that prevents third parties from detecting that confidential information is hidden in other media. Due to structural vulnerabilities, information protected by encryption and steganography techniques can be easily exposed to illegitimate groups. In order to improve the limitations of LSB where the simplicity and predictability of the hiding method exist, I propose a technique to improve the security of the message to be hidden based on PRNG and recursive function. To enhance security and confusion, XOR operation was performed on the result of selecting a random bit from the upper bits of the selected channel and the information transformed by the RS-box. PSNR and SSIM were used to confirm the performance of the proposed method. Compared to the reference values, the SSIM and PSNR of the proposed method were 0.9999 and 51.366, respectively, confirming that they were appropriate for hiding information.

• Journal of Electrochemical Science and Technology
• /
• v.15 no.1
• /
• pp.67-95
• /
• 2024

Direct alcohol fuel cells (DAFCs) have gained much attention as promising energy conversion devices due to their ability to utilize alcohol as a fuel source. In this regard, Molybdenum-based electrocatalysts (Mo-ECs) have emerged as a substitution for expensive Pt and Ru-based co-catalyst electrode materials in DAFCs, owing to their unique electrochemical properties useful for alcohol oxidation. The catalytic activity of Mo-ECs displays an increase in alcohol oxidation current density by several folds to 1000-2000 mA mg_Pt^-1, compared to commercial Pt and PtRu catalysts of 10-100 mA mg_Pt^-1. In addition, the methanol oxidation peak and onset potential have been significantly reduced by 100-200 mV and 0.5-0.6 V, respectively. The performance of Mo-ECs in both acidic and alkaline media has shown the potential to significantly reduce the Pt loading. This review aims to provide a comprehensive overview of the bifunctional mechanism involved in the oxidation of alcohols and factors affecting the electrocatalytic oxidation of alcohol, such as synthesis method, structural properties, and catalytic support materials. Furthermore, the challenges and prospects of Mo-ECs for DAFCs anode materials are discussed. This in-depth review serves as valuable insight toward enhancing the performance and efficiency of DAFC by employing Mo-ECs.

• Journal of Electrochemical Science and Technology
• /
• v.15 no.1
• /
• pp.198-206
• /
• 2024

Given the high theoretical capacity (1,675 mAh g^-1) and the inherent affordability and ubiquity of elemental sulfur, it stands out as a prominent cathode material for advanced lithium metal batteries. Traditionally, sulfur was sequestered within conductive porous carbons, rooted in the understanding that their inherent conductivity could offset sulfur's non-conductive nature. This study, however, pivots toward a transformative approach by utilizing diatom shell (DS, diatomite)-a naturally abundant and economically viable siliceous mineral-as a sulfur host. This approach enabled the development of a sulfurlayered diatomite/S composite (DS/S) for cathodic applications. Even in the face of the insulating nature of both diatomite and sulfur, the DS/S composite displayed vigorous participation in the electrochemical conversion process. Furthermore, this composite substantially curbed the loss of soluble polysulfides and minimized structural wear during cycling. As a testament to its efficacy, our Li-S battery, integrating this composite, exhibited an excellent cycling performance: a specific capacity of 732 mAh g^-1 after 100 cycles and a robust 77% capacity retention. These findings challenge the erstwhile conviction of requiring a conductive host for sulfur. Owing to diatomite's hierarchical porous architecture, eco-friendliness, and accessibility, the DS/S electrode boasts optimal sulfur utilization, elevated specific capacity, enhanced rate capabilities at intensified C rates, and steadfast cycling stability that underscore its vast commercial promise.

• Journal of Korean Ophthalmic Optics Society
• /
• v.10 no.3
• /
• pp.185-191
• /
• 2005

Photo-reactive $TiO_2$ thin films on soda-lime-silica slide glass were prepared by spin coating technique with a Ti-naphthenate precursor. Optical, structural and photo-catalytic properties of the films after annealing at $500^{\circ}C{\sim}600^{\circ}C$ were evaluated. As increase with annealing temperature, absorption bands and total transmittance of the films showing an average transmittance (about 80%) at visible spectra range were shifted to UV spectra range and slightly decreased. Refractive index and thickness of the films were increased from 2.16 to 2.63 and decreased from 484 nm to 439 nm, respectively, with increase of annealing temperature. Anatase phase was visible at all annealing temperature. More rougher surface structure was obtained at $600^{\circ}C$ than those of films annealed at $500^{\circ}C$ and $550^{\circ}C$. The hydrophilic conversion was found within 45 min by UV stimulation and optical activation was UVC>UVA>UVB at the case of $500^{\circ}C{\sim}550^{\circ}C$ and UVA>UVC>UVB at the annealing temperature of $600^{\circ}C$. The lowest initial contact angle was obtained at $600^{\circ}C$.

• Journal of KIISE:Databases
• /
• v.33 no.5
• /
• pp.526-537
• /
• 2006

The most representative approach for efficient storing of XML data is to store XML data in relational databases. The merit of this approach is that it can easily accept the realistic status that most data are still stored in relational databases. This approach needs to convert XML data into relational data or relational data into XML data. The most important issue in the translation is to reflect structural and semantic relations of RDB to XML schema model exactly. Many studies have been done to resolve the issue, but those methods have several problems: Not cover structural semantics or just support explicit referential integrity relations. In this paper, we propose an algorithm for extracting implicit referential integrities automatically. We also design and implement the suggested algorithm, and execute comparative evaluations using translated XML documents. The proposed algorithm provides several good points such as improving semantic information extraction and conversion, securing sufficient referential integrity of the target databases, and so on. By using the suggested algorithm, we can guarantee not only explicit referential integrities but also implicit referential integrities of the initial relational schema model completely. That is, we can create more exact XML schema model through the suggested algorithm.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.30 no.6
• /
• pp.495-500
• /
• 2017

In the boundary layer of supersonic or hypersonic vehicles, there is the conversion from kinetic energy to thermal energy, called aerodynamic heating. Aerodynamic heating has to be considered to design supersonic vehicles, because it induces severe heat flux to surface. Transient heat transfer analysis with CFD is used to predict thermal response of vehicles, however transient heat transfer analysis needs excessive computing powers. Loosely coupled method is widely used for evaluating thermal response, however it needs to be revised for overestimated heat flux. In this research, quasi-transient method, which is combined loosely coupled method and conjugate heat transfer analysis, is proposed for evaluating thermal response with efficiency and reliability. Defining reference time of splitting flight scenario for transient simulation is important on accuracy of quasi-transient method, however there is no algorithm to determine. Therefore the research suggests the algorithm with various flow conditions to define reference time. Supersonic flow field of blunt body with constant acceleration is calculated to evaluate quasi-transient method. Temperature difference between transient and quasi-transient method is about 11.4%, and calculation time reduces 28 times for using quasi-transient method.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.4
• /
• pp.665-670
• /
• 2020

Buffer layer in CIGS thin-film solar cells improves energy conversion efficiency through band alignment between the absorption layer and the window layer. ZnS is a non-toxic II-VI compound semiconductor with direct-transition band gaps and n-conductivity as well as with excellent lattice matching for CIGS absorbent layers. In this study, the structural and optical properties of ZnS thin films, deposited by RF magnetron sputtering method and subsequently performed by the rapid thermal annealing treatment, were investigated for the buffer layer. The zincblende cubic structures along (111), (220), and (311) were shown in all specimens. The rapid thermal annealed specimens at the relatively low temperatures were polycrystalline structure with the wurtzite hexagonal structures along (002). Rapid thermal annealing at high temperatures changed the polycrystalline structure to the single crystal of the zincblende cubic structures. Through the chemical analysis, the zincblende cubic structure was obtained in the specimen with the ratio of Zn/S near stoichiometry. ZnS thin film showed the shifted absorption edge towards the lower wavelength as annealing temperature increased, and the mean optical transmittance in the visible light range increased to 80.40% under 500℃ conditions.

• Journal of the Korean Society of Radiology
• /
• v.3 no.2
• /
• pp.27-31
• /
• 2009

Now a days, the Medical X-ray equipments has become digitalized from analog type such as film, cassette to CR, DR. And many scientists are still researching and developing the Medical X-ray equipment. In this study, we used the Bismuth tri-iodide to conversion material for digital X-ray equipments and we couldn't get the satisfying result than previous study, but it opened new possibility to cover the disadvantage of a-Se is high voltage aplly and difficultness of make. In this paper, we use $BiI_3$ powder(99.99%) as x-ray conversion material and make films that have thickness of 200um and the film size is $3cm{\times}3cm$. Also, we deposited an ITO(Indium Tin Oxide) electrode as top electrode and bottom electrode using a Magnetron Sputtering System. To evaluate a characteristics of the produced films, an electrical and structural properties are performed. Through a SEM analysis, we confirmed a surface and component part. And to analyze the electrical properties, darkcurrent, sensitivity and SNR(Signal to Noise Ratio) are measured. Darkcurrent is $1.6nA/cm^2$ and sensitivity is $0.629nC/cm^2$ and this study shows that the electrical properties of x-ray conversion material that made by screen printing method are similar to PVD method or better than that. This results suggest that $BiI_3$ is suitable for a replacement of a-Se because of the reduced manufacture processing and improved yield.