• Journal of the Korean Society of Combustion
• /
• v.2 no.1
• /
• pp.17-27
• /
• 1997

It is well known that NOx formation has a strong dependence on the maximum temperature and correspondingly with the maximum chamber pressure of a closed combustion system. However, in a case of impinging-jet-flame (IJF hereafter) combustion with opposed dual pre-chambers, low $NO_x$ formation with high pressure could be achieved, but its mechanism has not been clearly understood so far. In this study, a three-dimensional analysis is adopted to resolve time-variant local properties that might indicate the mechanism of IJF combustion. Numerical results are verified by comparing them with experiments. The IJF combustion in a vessel with no pre-chamber, with single pre-chamber, and with dual pre-chambers is studied. The orifice diameter and the volumetric ratio of pre-chamber are used as geometric parameters. The effects of main-chamber ignition delay time and combustion time of main-chamber, orifice exit velocity, orifice exit temperature, turbulent kinetic energy of main-chamber and spatial distribution of temperature in the latter stage of combustion are investigated. A longer main-chamber ignition delay and a shorter main-chamber combustion time suppress the formation of high temperature region with respect to mean temperature, which consequently results in less NO production.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.5
• /
• pp.1-11
• /
• 2006

The effects of continuous blowing on flow control and stall suppression for flows over a NACA 0015 airfoil at low Reynolds numbers were numerically investigated through its parameter variation on unstructured meshes. The aerodynamic force and moment variations due to flow control were examined, along with the stall angle-of-attack change for stall suppression. The results showed that blowing with relatively strong jet increases lift at the cost of drag increment below stall angle. Continuous blowing delays flow stall when it is implemented near the leading edge. When the blowing jet was aligned along the flow direction on the airfoil, the favorable flow control effect was most significant below the stall angle of attack.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.2
• /
• pp.24-32
• /
• 2008

A non-reacting experimental study on a normal injection into a Mach 1.92 crossflow which flows over various geometries(flat plate, small cavity, large cavity) was carried out to investigate the effect of the momentum flux ratio(J). The aft ramp of the cavity advances the increase of the penetration height and the strong two-dimensional shock from recompression region mainly affects the shock structure and mixing layer at the downstream flow. As flow runs downward, the transverse penetration height increases with increasing J(J = 0.9, 1.7, 3.4). However, above some critical ratio, jet penetration height growth with increasing J is not appeared in flow-field. Large scale cavity has a good mixing efficiency but it increases the drag loss in the combustor.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.16 no.3
• /
• pp.290-301
• /
• 2006

A push pull hood system is frequently applied to control contaminants evaporated from an open surface tank. Efficiency of push pull hood system is affected by various parameters, such as, cross draft, vessel shapes, tank surface area, liquid temperature. A previous work assisted by flow visualization technique qualitatively showed that a strong cross draft blown from the pull hood to push slot could destroy a stable wall-jet on the surface of tank, resulting in the abrupt escape of smoke from the surface. In this study, the tracer gas method was applied to determine the effect of cross-draft on the capture efficiency qualitatively. A new concept of capture efficiency was introduced, that is, linear efficiency. This can be determined by measuring the mass of tracer gas in the duct of pull hood while the linear tracer source is in between push slot and pull hood. By traversing the linear tracer source from the push slot to the pull hood, it can be found where the contaminant is escaped from the tank. Total capture efficiency can be determined by averaging the linear efficiencies. Under the condition of cross-draft velocities of 0, 0.4, 0.75, 1.05 and 1.47m/s, total capture efficiencies were measured as 97.6, 95.4, 94.6, 92.7 and 70.5% respectively. The abrupt reduction of efficiency with cross-draft velocity of 1.47m/s was due to the destruction of tank surface wall-jet by the counter-current cross-draft. The same phenomenon was observed in the previous flow visualization study. As an alternative to overcome this abrupt efficiency drop, the 20% increase of hood flow rates was tested, resulting in 20% efficiency increase.

• Journal of Forest and Environmental Science
• /
• v.33 no.4
• /
• pp.342-347
• /
• 2017

Since the first report of the oak wilt disease at 2004 in Korea, the disease distributed over Korean peninsula and are still giving severe damages. The management of oak wilt disease in Korea has mainly focused on the control of insect vector, Platypus koryoensis. Neverthless the effective method for evaluating the pathogenicity of the pathogen, Raffaelea quercus-mongolicae (Rqm), and for screening chemical or biological agents with strong inhibitory activity against the pathogen, is absolutely necessary, an reliable method is not available so far. This study was conducted to develop the effective method for evaluating the pathogenicity of Rqm in oak trees. The culture suspensions of Rqm were artificially injected to the saplings of Quercus acutissima by using ChemJet tree injector. Three months after treatments, the treated saplings were cut and dipped into 1% fuchsin acid solution. There were significant differences in non-conductive area (%), discoloration area (%) and vertical discoloration length between the pathogen-injected and distilled water-injected control treatments. These results indicated that the pathogen is the causal agent for the dysfunction of water conductive tissue, which will finally result in wilt symptom. Re-isolation of the pathogen and PCR detection using specific primers for the pathogen also confirmed the presence of Rqm in the sapwood chips of the pathogen-injected saplings. These observations would be greatly applied to other related researches for evaluating the pathogenicity of tree wilt pathogens and biocontrol efficacy of the selected antagonistic microorganisms, in case that the wilt symptom is not easily shown by artificial inoculation of the causal agent.

• Fire Science and Engineering
• /
• v.18 no.2
• /
• pp.34-40
• /
• 2004

The effects of external flow excitation with various frequencies and amplitudes on the flame behavior and pollution emission characteristics from a laminar jet flame are experimentally investigated. Measurements of $NO_x$ emission indices ($EINO_x$), performed in vertical lifted flame like turbulent with various exciting amplitude at a constant resonance frequency, have been conducted. It was also conducted to investigate the effects of excited frequency at a constant exciting amplitude on $NO_x$ emissions with a various frequency ranged 0 Hz to 2 KHz. From the vertical lifted turbulent flame of the excited jet with resonance frequency by strong excitation was shown that the dependence of $NO_x$ emission could be categorized into three groups Group I of long flame length with high disturbances yielding high $NO_x$ emission, Group II of intermediate flame length and relative narrow flame volume with low disturbance yielding low $NO_x$ emission and Group III of long flame length and large flame volume with high time ＆ space disturbances behaviour yielding high $NO_x$ emission.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.11 no.2
• /
• pp.37-48
• /
• 2006

HF radar-derived current data obtained in 2002 and 2004 are analyzed to examine the effects of the completion of the Saemangeum 4th tidal dyke in June 2003, connecting Gogunsan-Gundo and Bieung-Do, on the coastal surface $M_2$ current pattern. Comparison between the currents by HF radar and current meter mooring showed good agreements. Counterclockwise rotation of the $M_2$ current in the observed area did not change with the dyke construction. Strong westward ebb jet from the gap of the dyke was observed in 2002 but disappeared in 2004. The complete closing of the dyke gap caused the current speed increase around the mouth of the Kem River estuary, decrease around Gogunsan-Gundo and the dyke, the changes in the direction of maximum current to north-ward from eastward and the delay of the maximum flood current occurrence around Gogunsan-Gundo and the dyke. Around Yeon-Do, the maximum flood current directed more clockwise and occurred rather earlier. These changes of the $M_2$ current ellipse characteristics imply that the effects of the dyke construction reached the area connecting Mal-Do and Yeun-Do.

• Atmosphere
• /
• v.25 no.1
• /
• pp.31-49
• /
• 2015

From the hourly data of 75 Korean weather stations over a 12-year period (2001~2012), this study has chosen three cases (January 12, 2006; January 11, 2008; and February 22, 2009) of multiple freezing rains and investigated the atmospheric circulations that seemed to cause the events. As a result, the receding high pressure type (2006), prevailing high pressure type (2008), and warm front type (2009) are confirmed as synoptic patterns. In all three cases, freezing rain was found in regions with a strong ascending current near the end point of a low-level jet that carried the warm humid air from low latitudes. The strong ascending current resulted from lower-level convergence and upper-level divergence. In 2006 and 2009, the melting process was confirmed. In 2008, the supercooled warm rain process (SWRP) was confirmed. In contrast to existing SWRP theory, it was found that the cool air produced at the middle atmosphere and near the earth's surface led to the formation of freezing rain. The sources of this cool air were supposed to be the evaporative latent heat and the cold advection coming from the northeast. On the other hand, a special case was detected, in which the freezing rain occurred when both the soil surface temperature and surface air temperature were above $0^{\circ}C$. The thickness distributions related to freezing rain in Korea were found to be similar to those in North America. A P-type nomogram was considered for freezing rain forecasting; however, it was not relevant enough to Korea, and few modifications were needed.

• Journal of Embryo Transfer
• /
• v.33 no.3
• /
• pp.99-105
• /
• 2018

To determine the differences in the in-vitro ovum maturation process of bovine, we compared the expression of MMPs in these oocytes and cumulus cell throughout oocytes maturated. In an attempt to investigate the effect of MMP activation and inhibitors in total protein of cumulus cell and, oocytes during oocytes maturation, we examined and monitored the localization and expression of MMPs (MMP-2 and MMP-9), TIMPs (TIMP-2 and TIMP-3), as well as their expression profiles (Real-time PCR, Gelatin Zymography and ELISA). Our results that the bovine oocytes MMP-2 and MMP-9 level was significantly associated with the rate of maturity of oocytes (P<0.05). In cumulus cell, MMP-2 was highly expressed in all stages of the oocyte's maturation. The final oocytes maturation exhibited strong gelatinase activity. There was no significant correlation between cumulus cell MMP-9 and the maturation rate of oocytes. However, for the oocyte cytoplasm MMP-9 expression was significant correlation to the maturation oocytes. There was no significant correlation between cumulonimbus cells MMP-9 and oocyte maturation rates; however, for oocyte cytoplasm, MMP-9 expression was significantly correlated with mature oocyte. However, the TIMP-1 and TIMP-2 protein expression patterns are not correlated with the maturation rate of the oocyte. Our results suggest that MMP different expression pattern may regulate the morphological remodeling of oocyte's in the cumulus cell. Further, the MMP-2 expression has a strong relation with a higher maturation rate of the oocyte.

• Journal of the Society of Naval Architects of Korea
• /
• v.47 no.2
• /
• pp.132-140
• /
• 2010

The very erosive cavitation is simulated by an inclined propeller dynamometer in the medium-size cavitation tunnel of MOERI. The inclined shaft for propeller makes strong cavitaion, which occurs around the root of a propeller blade. The cavitation begins at the leading edge of the propeller and contracted toward the trailing edge through the reentrant jet action. The cavity focused on the region near the trailing edge collapsed over the blade surface. As the impact pressure by the cavitation collapsing is too strong, it can damage the blade surface in the form of pit. This cavitation impacts created by the collapsing process are similar to the full-scale ones and are different from those by other erosion test methods. The newly developed cavitation erosion test method can be applied to evaluate the materials such as metals, ceramics and coatings in terms of cavitation resistance.