• Corrosion Science and Technology
• /
• 제6권4호
• /
• pp.193-197
• /
• 2007

It is well known that the development of Advanced High Strength Steels (AHSS) is very important for the automotive industry in order to improve fuel efficiency and the reduction of material costs. However, it is particularly difficult to improve the surface quality of AHSS because the high amount of Si, Al, Mn and Ti etc. in AHSS promote selective oxidation, resulting in surface defects. The reheating process in the hot strip mill would cause severe oxidation because it is carried out at elevated temperatures under aggressive environments. In this study a reheating furnace simulator was developed to investigate oxidation phenomena in the reheating process. The environmental gas for the reheating furnace was made by burning coke oven gas with air in the simulator. The air/fuel ratio is precisely controlled by MFC. Ti oxides are easily formed on grain boundaries and Mn and Si oxides are usually formed in inner grains near the steel surface with a small round shape.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2003년도 봄 학술발표회 논문집
• /
• pp.455-462
• /
• 2003

The current practice of estimating bearing capacity usually employs the conventional bearing capacity formula originally developed for strip footings under vertical central loading, In order account for the effect of footing shape and eccentricity and inclination of loads, correction factors are introduced in the formula, which are derived based on a number of small-scale model test observations. In this paper, comparison of several formulations of bearing capacity factors, as well as values of these factors, are presented. And the conventional bearing capacity equations are compared with some of other failure loci proposed for cohesive soil. Also, the bearing capacity of shallow foundation estimated by the conventional bearing capacity equations are compared with the experimental load test results.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.142-146
• /
• 2001

In this study, it was investigated the influence of cold rolling factors on the edge drop. Edge drop was highly affected by the shape of work roll, the amount of work roll shift and the crown of hot strip, but the effect of bending force at the front stand was relatively small. The used numerical model was examined by comparing to the result of measured field data, and it showed a qualitative agreement with each other.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.71-74
• /
• 2001

Using the Taguchi method, optimum process condition of lead frame blanking has been determined in the point of view of shape of blanked profile. As the main process parameters, clearance, strip holding pressure and bridge width are selected. According to the orthogonal array table, three levels of experiment have been carried out for each factors. The optimal blanking condition is analyzed with the SN ratio. It has been verified that the optimal process condition can be determined with a combination of basic blanking experiment and experiment design method. Both the effect of each factors and gain can be judged in the quantitative manners from the analysis of SN ratio.

• 소성∙가공
• /
• 제11권2호
• /
• pp.132-137
• /
• 2002

Using the Taguchi method, optimum process condition of lead frame blanking has been determined in the point of view of shape of blanked profile. As the main process parameters, clearance, strip holding pressure and bridge width are selected. According to the orthogonal array table, three levels of experiment have been carried out for each factor. The optimal blanking condition is analyzed with the SN ratio. It has been verified that the optimal Process condition can be determined with a combination of basic blanking experiment and experiment design method. Both the effect of each factor and gain can be judged in the quantitative manner from the analysis of SN ratio.

• 한국전산유체공학회지
• /
• 제12권3호
• /
• pp.13-19
• /
• 2007

A numerical simulation on the heat transfer and flow field was carried out to improve the performance of the shell and tube heat exchanger. The steady incompressible 3-D Navier-Stokes solution is obtained with the actual operational condition and geometry of the heat exchanger. Based on this study, it is noted that the present geometry of the heat exchanger causes poor heat transfer since the air inside shell does not flow through the tube bundle, but around it. The enhancement of the heat transfer can be achieved by the variation of the design factor like the sealing strip located on the top/bottom and middle of the baffle, but it causes the increasement of the pressure drop. In this paper, the effects of the location and size of the sealing strips and flow rate through the heat exchanger on the heat transfer and pressure drop are studied.

• 소성∙가공
• /
• 제16권6호
• /
• pp.447-451
• /
• 2007

The springback characteristics of AZ31B magnesium alloy sheet was investigated in OSU draw/bend test Springback is the elastically-driven change of shape of a part after forming and it should be estimated and controlled to manufacture more precise products in sheet forming. Magnesium alloy sheets have unique mechanical properties such as high in-plane anisotropy/asymmetry of yield stress and hardening response. So, there will be a difference in the prediction of springback with symmetric mechanical properties for magnesium alloy sheets. In this work, the Strip draw/bend tests were conducted with various conditions - die radius, sheet thickness and controlled tensile force and the tendency of springback angle was observed from the tests.

• Structural Engineering and Mechanics
• /
• 제31권3호
• /
• pp.277-296
• /
• 2009

The paper investigates the dynamic behaviour of stiffened panels. The coupled differential equations for eccentric stiffening configuration are first derived. Then a semi-analytical procedure for dynamic analysis of stiffened panels is presented. Unlike finite element or finite strip methods, where the plate is discretized into a set of elements or strips, the plate in this procedure is treated as a single element. The potential energy of the structure is first expressed in terms generalized functions that describe the longitudinal and transverse displacement profiles. The resulting non-linear strain energy functions are then transformed into unconstrained optimization problem in which mathematical programming techniques are employed to determine the magnitude of the lowest natural frequency and the associated mode shape for pre-selected plate/stiffener geometric parameters. The described procedure is verified with other numerical methods for several stiffened panels. Results are then presented showing the variation of the natural frequency with plate/stiffener geometric parameters for various stiffening configurations.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1995년도 Proceedings of the Korea Automation Control Conference, 10th (KACC); Seoul, Korea; 23-25 Oct. 1995
• /
• pp.150-153
• /
• 1995

In this paper the attitude control system is developed for longitudinal motion of Foil-Catamaran in regular waves with all-movable foils which attached to fore and after part of the ship and verified the system by theoretical calculation and model-tests. The linearized equations of motion of the ship is employed to apply the linear control theories, the PID control and the LQR. The strip method was used to calculate hydrodynamic coefficients and wave exciting forces of the demi hull, and unsteady hydrodynamic forces of foils are considered by using the result of Wu(1972). About 40-60% of motions is reduced in experiments. The control system described in this paper is able to extended to 6-DOF motions or control in irregular wave with trivial modification. And it is applicable to hull shape development for better seakeeping performance and to determine the size and the position of hydrofoils for the attitude control.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 제3회 압연심포지엄 논문집 압연기술의 미래개척 (Exploitation of Future Rolling Technologies)
• /
• pp.3-9
• /
• 1999

The recent technical trend in hot rolling of steel can be described as process and product technologies which have been progressed with modern mill equipment and computers. Precise gauge and width control can be achieved by up-to-date control methods such as AGC and AWC systems. Roll benders and various shape control systems enabled high quality flatness and crown control. Mills can produce higher tensile materials by new process based on process metallurgy. The use of high speed steel rolls and on line roll grinders make the schedule free rolling easier which results in cost saving. Process itself goes toward continuous and simple flow type which has lower operation. Endless rolling and strip casting are examples of the trend. Materials with higher tensile strength and various functions have been developed in last years to meet the customer's needs and this trend will continue.