• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.3
• /
• pp.359-368
• /
• 2006

The trend on marine diesel engine productions and refinements has led to a higher mean effective pressure and thermal efficiency. These resulted in increased maximum combustion pressure within the cylinder and vibratory torque in crankshaft. In view of this. the crankshaft should be able to withstand the dynamic stresses caused by load variations. Different factors including size, material and stress concentration factors should also be considered to ensure the reliability of the shafting system. As such, crankshaft must be designed and compacted within its fatigue strength. In this paper, the strength analysis of crankshaft Is carried out by: simplified method recommended by IACS(International Association Classification Societies) M53 and a detailed method with the crankshaft assumed as a continuous beam and bearing supported in its flexibility. The results of these two methods are then compared.

• Journal of Applied Reliability
• /
• v.15 no.2
• /
• pp.124-130
• /
• 2015

A stress-strength analysis is used to assess the reliability of a multi-pulse rocket motor system. Main stress is found to be thermal during explosion and the distribution is obtained by simulation. The strength distribution is derived from the results of actual specimen tests. The failure rate of barrier type pulse separation device is estimated.

• Computers and Concrete
• /
• v.15 no.4
• /
• pp.607-642
• /
• 2015

The stress-strain relationship of concrete in flexure is one of the essential parameters in assessing the flexural strength and ductility of reinforced concrete (RC) columns. An overview of previous research studies revealed that the presence of strain gradient would affect the maximum concrete stress developed in flexure. However, no quantitative model was available to evaluate the strain gradient effect on concrete under flexure. Previously, the authors have conducted experimental studies to investigate the strain gradient effect on maximum concrete stress and respective strain and developed two strain-gradient-dependent factors k3 and ko for modifying the flexural concrete stress-strain curve. As a continued study, the authors herein will extend the investigation of strain gradient effects on flexural strength and ductility of RC columns to concrete strength up to 100 MPa by employing the strain-gradient-dependent concrete stress-strain curve using nonlinear moment-curvature analysis. It was evident from the results that both the flexural strength and ductility of RC columns are improved under strain gradient effect. Lastly, for practical engineering design purpose, a new equivalent rectangular concrete stress block incorporating the combined effects of strain gradient and concrete strength was proposed and validated. Design formulas and charts have also been presented for flexural strength and ductility of RC columns.

• Journal of Korean Port Research
• /
• v.14 no.3
• /
• pp.331-340
• /
• 2000

For the rational and economic design of the structural elements of ships which is built using welding, the ultimate strength analyses of the plates having initial imperfections, such as welding residual stresses and strains, are needful. The welding deformation usually relied on approximative equations or based on expert's experience. But in this paper, for the thermal elasto-plastic analysis of plates, the finite element analysis was performed, based on initial strain method. In formulating the incremental analysis, unbalanced force terns were included. In the plastic domain during the incremental process, the 2nd order terns stress increment and yield stress increment were considered, so that time increment could be controlled for a more stable solution. The ultimate strength analysis program of the plates having initial imperfections was made. The ultimate strength analysis was carried out based on the results of the welding deformations of this paper. In the ultimate strength analysis the Rayleigh-Ritz method based on the minimum potential theory was used.

• Journal of the Society of Naval Architects of Korea
• /
• v.40 no.6
• /
• pp.49-57
• /
• 2003

This method surely needs a hole that causes local strength and stiffness deterioration of the structure because of stress intensity. In this work, three dimensional stress analysis of pin-loaded joint for quasi-isotropic composite laminates was performed using commercial finite element software. Stress distribution was calculated near the edge of the pin-leaded hole and effects of the stacking sequence on the delamination were investigated. Also, the delamination strength of the composite laminates was predicted using the Ye-delamination failure criterion and compared with the experimental results. finally, newly modified failure criterion has been suggested owing to the consideration of effects of interlaminar normal stress on the delamination strength.

• Journal of Welding and Joining
• /
• v.11 no.4
• /
• pp.112-124
• /
• 1993

It has been reported that fatigue damage sometimes occurred at the stress concentrated and dynamic loaded structural members of bulk carrier. In this paper, studies on fatigue strength of hull structures are reviewed, and the program for evaluating fatigue strength is developed. And the fatigue crack initiation and propagation on the end part of cargo hold frame of bulk carrier were calculated by FEM stress analysis and the fatigue strength evaluation program. These method can be applied not only to the crack initiation life but also to crack propagation life for the hull structural members at the hull design stage and be effective as the guideline to prevent the crack initiation or to estimate the fatigue strength for repairing of the fatigue damaged structures of real ships.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.06a
• /
• pp.144-148
• /
• 2005

Cylinder frame manufactured by casting is assembled with the components such as cylinder head, cylinder liner and main bearing cap, etc. The mechanical contact between all of the neighboring components due to bolt tightening was taken into consideration. The loads used in structural analysis were the bolt tightening forces induced by hydraulic jack and the dynamic forces calculated from kinematic analysis. The difference of forces between the neighboring cylinders was taken into account. The maximum stress, stress amplitude and mean stress calculated from the results of structural analyses were used to evaluate the static and fatigue strength. Gray cast iron which is material of cylinder frame has the material characteristics of very small elongation and different strength in tension and compression. Based on such an material characteristics, the strength evaluation of cylinder frame was carried out with in-house program developed internally.

• Journal of the Korean GEO-environmental Society
• /
• v.11 no.4
• /
• pp.19-24
• /
• 2010

Generally, slope behavior is analyzed by 2-dimensional creep model. Creep behavior shows the deformation variation as time goes by without stress increment. Convention 2-dimensional creep analysis does not have the term of stress variation, it means creep analysis could not figure out the relationship of shear strength variation according to the stress variation and displacement. The slope weight and shear strength is directly related and interlocked to the safety variation and displacement of slope, therefore, this phenomenon could be treated and analyzed as combining the hysteresis and creep, the iteration of this process will result in the slope safety. Furthermore, the combined analysis will be the slope analysis considering shear stress, displacement and shear strength with time variation. In real case, because the variation of shear stress and strength happen at the same time, they should be changed into safety factor which is function of them. This paper shows the 3-dimensional variation of unit weight of soil with hybrid analysis considering creep and hysteresis on the seepage and drainage of rainfall, futhermore variations of shear stress and strength which make the safety factor change.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.6
• /
• pp.97-103
• /
• 2008

In general, the strength of gears is calculated using the formula of AGMA or JGMA. But these formula can not be applied directly to the strength calculation of the rack and pinion of steering gear assay, because of complex tooth and contact shapes. So Lewis bending stress and Hertzian contact stress formula are generally used for the design of rack and pinion of steering gear assay. But these formula do not also give the exact stress of rack and pinion. In this paper, comparing the finite element analysis results and the experimentally measured values, it is shown that the finite element modeling technique of the rack and pinion of steering assay is reasonable.

• Journal of Industrial Technology
• /
• v.20 no.A
• /
• pp.169-178
• /
• 2000

The 4-point bending tests have been performed In order to estimate the effect of TIG-dressing on fatigue strength and fatigue characteristics quantitatively for non load-carrying fillet welded joints subjected to pure bending. As a result of fatigue tests, fatigue strengths of as-welded specimens have satisfied the grade of fatigue strength prescribed in specifications of korea, AASHTO and JSSC. Fatigue strength at 2 million cycles of TIG-dressing specimens have increased compared with as-welded specimens. As the result of beachmark tests, fatigue cracks occurred at several points, where the radius of curvature and flank angle in the weld bead toes were low, and grew as semi-elliptical cracks, then approached to fracture. As a result of finite element analysis, stress concentration factor in weld bead toes has closely related to the flank angle and radius of curvature, and between these, the radius of curvature has more largely affected in stress concentration factor than flank angle. As a result of fracture mechanics approaches, the crack correction factor of test specimens has largely affected on stress gradient correction factor in case a/t is below 0.4. From the relations between stress intensity factor range estimated from FEM analysis and fatigue crack growth rate, fatigue life has been correctly calculated.